Maxon Telecom MM-6280IND manual Pcca STD‑101 17 select wireless network +WS46

Page 21

		command +<name>s, which is intended to permit the user
		of the MT2 to identify the minimum capabilities of the MT2.
		An MT2 conforming to this standard shall include the
		following items, as a minimum, in the result code for the
		+GCAP command:
		+CIS707, +MS, +ES, +DS, +FCLASS (Default)
+GCI=<T.35>	Opt.	selects the country of installation for the TA using ITU T	Not supported
		Recommendation T.35 Annex A country codes

1.16. PCCA STD‑101 [17] select wireless network +WS46

Table 12. PCCA STD‑101 [17] select wireless network +WS46

Command	Req	Description
+WS46		select wireless network

Support

1.17. Informative examples

1.17.1.Phone model

Command: AT+CGMM

Expected response: Model

1.17.2.Phone Manufacturer

Command: AT+CGMI

Expected response: Manufacturer

1.17.3.Checking mobile state

Command: AT+CPAS

Expected response:+CPAS: State

State possible values:

0:available

3:ringing

4:call in progress

1.17.4.Firmware version reading

Command: AT+CGMR

Expected response: +CGMR: Firmware

1.17.5.IMEI number reading

Command: AT+CGSN

Expected response: +CGSN: IMEI

HSDPA Standard At Commands

Page 21 of 60

Version 1.2

Image 21

Contents Hsdpa Standard AT Commands Manual Document Description Revision History Contact Information Table of Contents Qualcomm commands General IntroductionTerms Terms definition3GPP TS ReferencesITU-T Recommendation E.212 GSM MoU SE.13ITU-T Recommendation T.31 ITU-T Recommendation T.32ITU-T Recommendation Ccitt RecommendationEtsi TS 102 RFC 3748, JuneAT command Format Command FormatBasic Integration Serial InterfaceDTE-TA/DCE interface commands MT2 TE2TE2 MT2 +ICF TE2-MT2+IFC +ILRR Report Mobile Termination error +CMEE Mobile Termination errors commandsMobile Termination error result code CME Error +CMEE parameter command syntaxHsdpa Standard At Commands AT+CGMI +CME Error AT+CMEE=2 AT+CGMI Error AT+CMEE=1Informative examples AT+CMEE=0 General commands Request manufacturer identification+CGMI Request model identification+CGMM +CGSN action command syntax +CGMM action command syntax+CSCS parameter command syntax Request product serial number identification +CGSNITU-T V.250 generic TA control commands Pcca STD‑101 17 select wireless network +WS46 Supported alphabets Network service commands Subscriber number +CNUM +CNUM action command syntaxNetwork registration +CREG +CNUMPlmn selection +COPS +CREG parameter command syntax+CREG? +CREG=?Applicable in read command response Facility lock +CLCK When mode=2 and command successfulUnlock Lock Query status Change password +CPWD +CPWD action command syntaxPreferred Plmn list +CPOL +COPN action command syntax +COLP parameter command syntaxRead operator names +COPN Operator information readingGprs Attachment Imsi number readingNetwork registration Own number readingMobile Termination control and status commands Basic TEBasic TE +CSQ action command syntax Signal quality +CSQ+CCLK parameter command syntax Clock +CCLKAT$$MBAND Write Command AT$$MBAND Read Command+CPIN parameter command syntax Band Selection AT$$MBANDPH-SIM PIN Signal strength readingPin registration Packet Domain CommandGPRS Umts packet Domain commandsUmts packet Domain commands Command Req Description Support Define PDP Context +CGDCONT +CGDCONT parameter command syntax+CGDCONT? +CGDCONT=?PPP Define Secondary PDP Context +CGDSCONTError Traffic Flow Template +CGTFT+CGDSCONT? + Cgtft parameter command syntax +CGTFT? +CGTFT=? + Cgqreq parameter command syntax Quality of Service Profile Requested +CGQREQ+ Cgqmin parameter command syntax Quality of Service Profile Minimum acceptable +CGQMIN+ Cgeqreq parameter command syntax Quality of Service Profile Requested +CGEQREQCRLF+CGQMIN SDU+CGEQREQ=? +CGEQREQ?Subscribed value. Other values are reserved PDPtype see +CGDCONT and +CGDSCONT commands Quality of Service Profile Minimum acceptable +CGEQMIN+CGEQMIN? + Cgeqmin parameter command syntaxCRLF+CGEQMIN +CGEQMIN=?Following parameters are defined in 3GPP TS 23.107 Quality of Service Profile Negotiated +CGEQNEG +CGEQNEG action command syntax +CGEQNEG+CGEQNEG=? PS attach or detach +CGATT + Cgatt parameter command syntax + Cgact parameter command syntaxPDP context activate or deactivate +CGACT PDP Context Modify +CGCMOD + Cgcmod parameter command syntaxEnter data state +CGDATA +CGCMOD=?Show PDP address +CGPADDR + Cgdata parameter command syntax+ Cgpaddr parameter command syntax Modem compatibility commandsUmts Connection +CGPADDR=?Synchronous data mode commands Qualcomm commands Qualcomm commandDescription Operation Support $QCPWRDN $QCPINSTAT$QCDGEN= $QCSLOT=

Related manuals

Manual 70 pages 35.54 Kb