Maxon Telecom MM-6280IND manual PDP context activate or deactivate +CGACT

Page 54

Table 36. + CGATT parameter command syntax

Command	Possible response(s)
+CGATT=	OK
[<state>]	ERROR
+CGATT?	+CGATT: <state>
+CGATT=?	+CGATT: (list of supported <state>s)
Value	<state>: indicates the state of PS attachment
Value	0 - detached
	1 - attached
	Other values are reserved and will result in an ERROR response to the execution
	command.

1.32.10.PDP context activate or deactivate +CGACT

The execution command is used to activate or deactivate the specified PDP context (s). After the command has completed, the MT remains in V.25ter command state. If any PDP context is already in the requested state, the state for that context remains unchanged. If the requested state for any specified context cannot be achieved, an ERROR or +CME ERROR response is returned. Extended error responses are enabled by the +CMEE command. If the MT is not PS attached when the activation form of the command is executed, the MT first performs a PS attach and them attempts to activate the specified contexts. If the attach fails then the MT responds with ERROR or, if extended error responses are enabled, with the appropriate failure-to-attach error message.

If no <cid>s are specified the activation form of the command activates all defined contexts.

If no <cid>s are specified the deactivation form of the command deactivates all active contexts.

The read command returns the current activation states for all the defined PDP contexts.

The test command is used for requesting information on the supported PDP context activation states.

	NOTE.	This command has the characteristics of both the V.25ter action and parameter
	commands. Hence it has the read form in addition to the execution/set and test forms.
	Table 37. + CGACT parameter command syntax
	Command			Possible response(s)
+CGACT=[<state>			OK
[,<cid>[,<cid>[,…			ERROR
]]]]
+CGACT?			+CGACT:<cid>,<state>[<CR><LF>+CGACT:<cid>,<state>[...]]
+CGACT=?			+CGACT: (list of supported <state>s)
Value			<state>: indicates the state of PDP context activation
Value			0 - deactivated
			1 - activated
			Other values are reserved and will result in an ERROR response to the
			execution command.
			<cid>: a numeric parameter which specifies a particular PDP context definition
			(see the +CGDCONT and +CGDSCONT commands).


	HSDPA Standard At Commands			Page 54 of 60	Version 1.2

Image 54

Contents Hsdpa Standard AT Commands Manual Document Description Revision History Contact Information Table of Contents Qualcomm commands Terms IntroductionGeneral Terms definitionReferences 3GPP TSITU-T Recommendation T.31 GSM MoU SE.13ITU-T Recommendation E.212 ITU-T Recommendation T.32Etsi TS 102 Ccitt RecommendationITU-T Recommendation RFC 3748, JuneBasic Integration Command FormatAT command Format Serial InterfaceDTE-TA/DCE interface commands MT2 TE2TE2 MT2 +ICF TE2-MT2+IFC +ILRR Mobile Termination error result code CME Error Mobile Termination errors commandsReport Mobile Termination error +CMEE +CMEE parameter command syntaxHsdpa Standard At Commands Informative examples AT+CGMI Error AT+CMEE=1AT+CGMI +CME Error AT+CMEE=2 AT+CMEE=0General commands Request manufacturer identification+CGMIRequest model identification+CGMM +CSCS parameter command syntax +CGMM action command syntax+CGSN action command syntax Request product serial number identification +CGSNITU-T V.250 generic TA control commands Pcca STD‑101 17 select wireless network +WS46 Supported alphabets Network service commands Network registration +CREG +CNUM action command syntaxSubscriber number +CNUM +CNUM+CREG? +CREG parameter command syntaxPlmn selection +COPS +CREG=?Applicable in read command response When mode=2 and command successful Facility lock +CLCKUnlock Lock Query status Change password +CPWD +CPWD action command syntaxPreferred Plmn list +CPOL Read operator names +COPN +COLP parameter command syntax+COPN action command syntax Operator information readingNetwork registration Imsi number readingGprs Attachment Own number readingMobile Termination control and status commands Basic TEBasic TE +CCLK parameter command syntax Signal quality +CSQ+CSQ action command syntax Clock +CCLK+CPIN parameter command syntax AT$$MBAND Read CommandAT$$MBAND Write Command Band Selection AT$$MBANDSignal strength reading PH-SIM PINPin registration Packet Domain CommandGPRS Umts packet Domain commandsUmts packet Domain commands Command Req Description Support +CGDCONT? +CGDCONT parameter command syntaxDefine PDP Context +CGDCONT +CGDCONT=?Define Secondary PDP Context +CGDSCONT PPPError Traffic Flow Template +CGTFT+CGDSCONT? + Cgtft parameter command syntax +CGTFT? +CGTFT=? Quality of Service Profile Requested +CGQREQ + Cgqreq parameter command syntaxQuality of Service Profile Minimum acceptable +CGQMIN + Cgqmin parameter command syntaxCRLF+CGQMIN Quality of Service Profile Requested +CGEQREQ+ Cgeqreq parameter command syntax SDU+CGEQREQ? +CGEQREQ=?Subscribed value. Other values are reserved Quality of Service Profile Minimum acceptable +CGEQMIN PDPtype see +CGDCONT and +CGDSCONT commandsCRLF+CGEQMIN + Cgeqmin parameter command syntax+CGEQMIN? +CGEQMIN=?Following parameters are defined in 3GPP TS 23.107 Quality of Service Profile Negotiated +CGEQNEG +CGEQNEG action command syntax +CGEQNEG+CGEQNEG=? PS attach or detach +CGATT + Cgatt parameter command syntax + Cgact parameter command syntaxPDP context activate or deactivate +CGACT Enter data state +CGDATA + Cgcmod parameter command syntaxPDP Context Modify +CGCMOD +CGCMOD=?+ Cgdata parameter command syntax Show PDP address +CGPADDRUmts Connection Modem compatibility commands+ Cgpaddr parameter command syntax +CGPADDR=?Synchronous data mode commands Qualcomm commands Qualcomm commandDescription Operation Support $QCDGEN= $QCPINSTAT$QCPWRDN $QCSLOT=

Related manuals

Manual 70 pages 35.54 Kb