Maxon Telecom MM-6280IND manual Quality of Service Profile Minimum acceptable +CGQMIN

Page 44

+CGQREQ=?

+CGQREQ: <PDP_type>, (list of supported <precedence>s), (list

 

of supported <delay>s), (list of supported <reliability>s) ,

 

(list of supported <peak>s), (list of supported <mean>s)

 

[<CR><LF>+CGQREQ:<PDP_type>,(list of supported

 

<precedence>s), (list of supported <delay>s), (list of

 

supported <reliability>s) , (list of supported <peak>s), (list

 

of supported <mean>s)[…]]

Value

<cid>: a numeric parameter which specifies a particular PDP context definition (see the

+CGDCONT and +CGDSCONT commands).

 

The following parameters are defined in 3GPP TS 23.107 [46]:

 

<precedence>: a numeric parameter which specifies the precedence class

 

<delay>: a numeric parameter which specifies the delay class

 

<reliability>: a numeric parameter which specifies the reliability class

 

<peak>: a numeric parameter which specifies the peak throughput class

 

<mean>: a numeric parameter which specifies the mean throughput class

 

If a value is omitted for a particular class then the value is considered to be

 

unspecified.

 

 

1.32.5.Quality of Service Profile (Minimum acceptable) +CGQMIN

This command allows the TE to specify a minimum acceptable profile which is checked by the MT against the negotiated profile returned in the Activate PDP Context Accept message.

The set command specifies a profile for the context identified by the (local) context identification parameter, <cid>. Since this is the same parameter that is used in the +CGDCONT and +CGDSCONT commands, the +CGQMIN command is effectively an extension to these commands. The QoS profile consists of a number of parameters, each of which may be set to a separate value.

A special form of the set command, +CGQMIN= <cid> causes the minimum acceptable profile for context number <cid> to become undefined. In this case no check is made against the negotiated profile.

The read command returns the current settings for each defined context.

The test command returns values supported as a compound value. If the MT supports several PDP types, the parameter value ranges for each PDP type are returned on a separate line.

Table 32. + CGQMIN parameter command syntax

Command

 

Possible response(s)

+CGQMIN=[<cid>

 

OK

[,<precedence

>

ERROR

[,<delay>

 

 

[,<reliability.>

 

 

[,<peak>

 

 

[,<mean>]]]]]]

 

 

+CGQMIN?

 

+CGQMIN: <cid>, <precedence >, <delay>, <reliability>,

 

 

<peak>,<mean>[<CR><LF>+CGQMIN: <cid>, <precedence >, <delay>,

 

 

<reliability.>,<peak>,<mean>[…]]

HSDPA Standard At Commands

Page 44 of 60

Version 1.2

Page 43 Page 45
Image 44
Page 43 Page 45
Contents Hsdpa Standard AT Commands Manual Document Description Revision History Contact Information Table of Contents Qualcomm commands Introduction GeneralTerms Terms definitionReferences 3GPP TSGSM MoU SE.13 ITU-T Recommendation E.212ITU-T Recommendation T.31 ITU-T Recommendation T.32Ccitt Recommendation ITU-T RecommendationEtsi TS 102 RFC 3748, JuneCommand Format AT command FormatBasic Integration Serial InterfaceTE2 MT2 DTE-TA/DCE interface commandsMT2 TE2 +IFC +ICFTE2-MT2 +ILRR Mobile Termination errors commands Report Mobile Termination error +CMEEMobile Termination error result code CME Error +CMEE parameter command syntaxHsdpa Standard At Commands AT+CGMI Error AT+CMEE=1 AT+CGMI +CME Error AT+CMEE=2Informative examples AT+CMEE=0Request model identification+CGMM General commandsRequest manufacturer identification+CGMI +CGMM action command syntax +CGSN action command syntax+CSCS parameter command syntax Request product serial number identification +CGSNITU-T V.250 generic TA control commands Pcca STD‑101 17 select wireless network +WS46 Supported alphabets Network service commands +CNUM action command syntax Subscriber number +CNUMNetwork registration +CREG +CNUM+CREG parameter command syntax Plmn selection +COPS+CREG? +CREG=?Applicable in read command response When mode=2 and command successful Facility lock +CLCKUnlock Lock Query status Preferred Plmn list +CPOL Change password +CPWD+CPWD action command syntax +COLP parameter command syntax +COPN action command syntaxRead operator names +COPN Operator information readingImsi number reading Gprs AttachmentNetwork registration Own number readingBasic TE Mobile Termination control and status commandsBasic TE Signal quality +CSQ +CSQ action command syntax+CCLK parameter command syntax Clock +CCLKAT$$MBAND Read Command AT$$MBAND Write Command+CPIN parameter command syntax Band Selection AT$$MBANDSignal strength reading PH-SIM PINPin registration Umts packet Domain commands Command Req Description Support Packet Domain CommandGPRSUmts packet Domain commands +CGDCONT parameter command syntax Define PDP Context +CGDCONT+CGDCONT? +CGDCONT=?Define Secondary PDP Context +CGDSCONT PPP+CGDSCONT? ErrorTraffic Flow Template +CGTFT + Cgtft parameter command syntax +CGTFT? +CGTFT=? Quality of Service Profile Requested +CGQREQ + Cgqreq parameter command syntaxQuality of Service Profile Minimum acceptable +CGQMIN + Cgqmin parameter command syntaxQuality of Service Profile Requested +CGEQREQ + Cgeqreq parameter command syntaxCRLF+CGQMIN SDU+CGEQREQ? +CGEQREQ=?Subscribed value. Other values are reserved Quality of Service Profile Minimum acceptable +CGEQMIN PDPtype see +CGDCONT and +CGDSCONT commands+ Cgeqmin parameter command syntax +CGEQMIN?CRLF+CGEQMIN +CGEQMIN=?Following parameters are defined in 3GPP TS 23.107 Quality of Service Profile Negotiated +CGEQNEG +CGEQNEG=? +CGEQNEG action command syntax+CGEQNEG PS attach or detach +CGATT PDP context activate or deactivate +CGACT + Cgatt parameter command syntax+ Cgact parameter command syntax + Cgcmod parameter command syntax PDP Context Modify +CGCMODEnter data state +CGDATA +CGCMOD=?+ Cgdata parameter command syntax Show PDP address +CGPADDRModem compatibility commands + Cgpaddr parameter command syntaxUmts Connection +CGPADDR=?Synchronous data mode commands Description Operation Support Qualcomm commandsQualcomm command $QCPINSTAT $QCPWRDN$QCDGEN= $QCSLOT=
Related manuals
Manual 70 pages 35.54 Kb
Top Page Image Contents