Maxon Telecom MM-6280IND manual Table of Contents

Page 5

TABLE OF CONTENTS


HSDPA Standard AT Commands Manual				1
Document Description				2
REVISION HISTORY				3
CONTACT INFORMATION				4
TABLE OF CONTENTS				5
Introduction				7
1.1.	General			7
1.2.	Terms			7
1.3.	References			8
AT INTERFACE DESCRIPTION				11
1.4.	Basic Integration			11
1.5.	Serial Interface			11
1.6.	Command Format			11
1.7.	Message Naming Convention			11
1.8.	DTE-TA/DCE interface commands			12
Mobile Termination errors commands				15
1.9. Report Mobile Termination error( +CMEE)				15
1.9.1. Mobile Termination error result code (CME ERROR)				15
1.10.	Informative examples			17
General commands				18
1.11.	Request manufacturer identification(+CGMI)			18
1.12.	Request model identification(+CGMM )			18
1.13. Request product serial number identification (+CGSN)				19
1.14. Select TE character set (+CSCS)				19
1.15. ITU-T V.250 generic TA control commands				20
1.16. PCCA STD‑101 [17] select wireless network +WS46				21
1.17.	Informative examples			21
1.17.1.		Phone model		21
1.17.2.		Phone Manufacturer		21
1.17.3.		Checking mobile state		21
1.17.4.		Firmware version reading	..........................................................................................	21
1.17.5.		IMEI number reading		21
1.17.6.		Supported alphabets		22
1.17.7.		Supported alphabets		22
Network service commands				23
1.18.	Subscriber number +CNUM			24
1.19.	Network registration +CREG			24
1.20.	PLMN selection +COPS			25
1.21.	Facility lock +CLCK			27
1.22.	Change password +CPWD			29
1.23. Preferred PLMN list +CPOL				29
HSDPA Standard At Commands			Page 5 of 60	Version 1.2

Image 5

Contents Hsdpa Standard AT Commands Manual Document Description Revision History Contact Information Table of Contents Qualcomm commands General IntroductionTerms Terms definition3GPP TS ReferencesITU-T Recommendation E.212 GSM MoU SE.13ITU-T Recommendation T.31 ITU-T Recommendation T.32ITU-T Recommendation Ccitt RecommendationEtsi TS 102 RFC 3748, JuneAT command Format Command FormatBasic Integration Serial InterfaceTE2 MT2 DTE-TA/DCE interface commandsMT2 TE2 +IFC +ICFTE2-MT2 +ILRR Report Mobile Termination error +CMEE Mobile Termination errors commandsMobile Termination error result code CME Error +CMEE parameter command syntaxHsdpa Standard At Commands AT+CGMI +CME Error AT+CMEE=2 AT+CGMI Error AT+CMEE=1Informative examples AT+CMEE=0Request model identification+CGMM General commandsRequest manufacturer identification+CGMI +CGSN action command syntax +CGMM action command syntax+CSCS parameter command syntax Request product serial number identification +CGSNITU-T V.250 generic TA control commands Pcca STD‑101 17 select wireless network +WS46 Supported alphabets Network service commands Subscriber number +CNUM +CNUM action command syntaxNetwork registration +CREG +CNUMPlmn selection +COPS +CREG parameter command syntax+CREG? +CREG=?Applicable in read command response Facility lock +CLCK When mode=2 and command successfulUnlock Lock Query status Preferred Plmn list +CPOL Change password +CPWD+CPWD action command syntax +COPN action command syntax +COLP parameter command syntaxRead operator names +COPN Operator information readingGprs Attachment Imsi number readingNetwork registration Own number readingBasic TE Mobile Termination control and status commandsBasic TE +CSQ action command syntax Signal quality +CSQ+CCLK parameter command syntax Clock +CCLKAT$$MBAND Write Command AT$$MBAND Read Command+CPIN parameter command syntax Band Selection AT$$MBANDPH-SIM PIN Signal strength readingPin registration Umts packet Domain commands Command Req Description Support Packet Domain CommandGPRSUmts packet Domain commands Define PDP Context +CGDCONT +CGDCONT parameter command syntax+CGDCONT? +CGDCONT=?PPP Define Secondary PDP Context +CGDSCONT+CGDSCONT? ErrorTraffic Flow Template +CGTFT + Cgtft parameter command syntax +CGTFT? +CGTFT=? + Cgqreq parameter command syntax Quality of Service Profile Requested +CGQREQ+ Cgqmin parameter command syntax Quality of Service Profile Minimum acceptable +CGQMIN+ Cgeqreq parameter command syntax Quality of Service Profile Requested +CGEQREQCRLF+CGQMIN SDU+CGEQREQ=? +CGEQREQ?Subscribed value. Other values are reserved PDPtype see +CGDCONT and +CGDSCONT commands Quality of Service Profile Minimum acceptable +CGEQMIN+CGEQMIN? + Cgeqmin parameter command syntaxCRLF+CGEQMIN +CGEQMIN=?Following parameters are defined in 3GPP TS 23.107 Quality of Service Profile Negotiated +CGEQNEG +CGEQNEG=? +CGEQNEG action command syntax+CGEQNEG PS attach or detach +CGATT PDP context activate or deactivate +CGACT + Cgatt parameter command syntax+ Cgact parameter command syntax PDP Context Modify +CGCMOD + Cgcmod parameter command syntaxEnter data state +CGDATA +CGCMOD=?Show PDP address +CGPADDR + Cgdata parameter command syntax+ Cgpaddr parameter command syntax Modem compatibility commandsUmts Connection +CGPADDR=?Synchronous data mode commands Description Operation Support Qualcomm commandsQualcomm command $QCPWRDN $QCPINSTAT$QCDGEN= $QCSLOT=

Related manuals

Manual 70 pages 35.54 Kb