Maxon Telecom MM-6280IND manual Facility lock +CLCK, When mode=2 and command successful

Page 27

2current

3forbidden

<AcT> access technology selected:

0GSM

1GSM Compact

2UTRAN

1.21.Facility lock +CLCK

Execute command is used to lock, unlock or interrogate a MT or a network facility <fac>. Password is normally needed to do such actions. When querying the status of a network service (<mode>=2) the response line for 'not active' case (<status>=0) should be returned only if service is not active for any <class>.

. This command should be abortable when network facilities are set or interrogated.

Call barring facilities are based on GSM/UMTS supplementary services (refer 3GPP TS 22.088 [6]). The interaction of these with other commands based on other GSM/UMTS supplementary services is described in the GSM/UMTS standard.

Test command returns facility values supported as a compound value.

Table 17. +CREG parameter command syntax

Command		Possible response(s)
+CLCK=<fac>,<mode>[,<	+CME ERROR: <err>
passwd>[,<class>]]	when <mode>=2 and command successful:
	+CLCK: <status>[,<class1>
	[<CR><LF>+CLCK: <status>,<class2>
	[...]]
+CLCK=?	+CLCK:	(list of supported	s
	+CLCK:		<fac> )
	+CME ERROR: <err>

HSDPA Standard At Commands

Page 27 of 60

Version 1.2

Image 27

Contents Hsdpa Standard AT Commands Manual Document Description Revision History Contact Information Table of Contents Qualcomm commands Terms definition IntroductionGeneral Terms3GPP TS ReferencesITU-T Recommendation T.32 GSM MoU SE.13ITU-T Recommendation E.212 ITU-T Recommendation T.31RFC 3748, June Ccitt RecommendationITU-T Recommendation Etsi TS 102Serial Interface Command FormatAT command Format Basic IntegrationDTE-TA/DCE interface commands MT2 TE2TE2 MT2 +ICF TE2-MT2+IFC +ILRR +CMEE parameter command syntax Mobile Termination errors commandsReport Mobile Termination error +CMEE Mobile Termination error result code CME ErrorHsdpa Standard At Commands AT+CMEE=0 AT+CGMI Error AT+CMEE=1AT+CGMI +CME Error AT+CMEE=2 Informative examplesGeneral commands Request manufacturer identification+CGMIRequest model identification+CGMM Request product serial number identification +CGSN +CGMM action command syntax+CGSN action command syntax +CSCS parameter command syntaxITU-T V.250 generic TA control commands Pcca STD‑101 17 select wireless network +WS46 Supported alphabets Network service commands +CNUM +CNUM action command syntax Subscriber number +CNUM Network registration +CREG+CREG=? +CREG parameter command syntaxPlmn selection +COPS +CREG?Applicable in read command response Facility lock +CLCK When mode=2 and command successfulUnlock Lock Query status Change password +CPWD +CPWD action command syntaxPreferred Plmn list +CPOL Operator information reading +COLP parameter command syntax+COPN action command syntax Read operator names +COPNOwn number reading Imsi number readingGprs Attachment Network registrationMobile Termination control and status commands Basic TEBasic TE Clock +CCLK Signal quality +CSQ+CSQ action command syntax +CCLK parameter command syntaxBand Selection AT$$MBAND AT$$MBAND Read CommandAT$$MBAND Write Command +CPIN parameter command syntaxPH-SIM PIN Signal strength readingPin registration Packet Domain CommandGPRS Umts packet Domain commandsUmts packet Domain commands Command Req Description Support +CGDCONT=? +CGDCONT parameter command syntaxDefine PDP Context +CGDCONT +CGDCONT?PPP Define Secondary PDP Context +CGDSCONTError Traffic Flow Template +CGTFT+CGDSCONT? + Cgtft parameter command syntax +CGTFT? +CGTFT=? + Cgqreq parameter command syntax Quality of Service Profile Requested +CGQREQ+ Cgqmin parameter command syntax Quality of Service Profile Minimum acceptable +CGQMINSDU Quality of Service Profile Requested +CGEQREQ+ Cgeqreq parameter command syntax CRLF+CGQMIN+CGEQREQ=? +CGEQREQ?Subscribed value. Other values are reserved PDPtype see +CGDCONT and +CGDSCONT commands Quality of Service Profile Minimum acceptable +CGEQMIN+CGEQMIN=? + Cgeqmin parameter command syntax+CGEQMIN? CRLF+CGEQMINFollowing parameters are defined in 3GPP TS 23.107 Quality of Service Profile Negotiated +CGEQNEG +CGEQNEG action command syntax +CGEQNEG+CGEQNEG=? PS attach or detach +CGATT + Cgatt parameter command syntax + Cgact parameter command syntaxPDP context activate or deactivate +CGACT +CGCMOD=? + Cgcmod parameter command syntaxPDP Context Modify +CGCMOD Enter data state +CGDATAShow PDP address +CGPADDR + Cgdata parameter command syntax+CGPADDR=? Modem compatibility commands+ Cgpaddr parameter command syntax Umts ConnectionSynchronous data mode commands Qualcomm commands Qualcomm commandDescription Operation Support $QCSLOT= $QCPINSTAT$QCPWRDN $QCDGEN=

Related manuals

Manual 70 pages 35.54 Kb