Qualcomm commands
Table 43. Qualcomm command
| COMMAND |
|
| Description |
| Operation |
|
| Support |
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| $QCCLR |
|
| clear mobile error log |
| Clears the mobile error log |
|
| Supported |
|
|
|
|
|
|
| Returns OK and then transitions the |
|
|
| |
|
|
|
|
|
| mobile’s serial port to DM mode; DM |
|
|
| |
| $QCDMG |
|
| transition to diagnostics |
| mode runs at rate set by $QCDMR |
| Supported |
| |
|
|
| monitor operation |
| command and uses a proprietary |
|
| |||
|
|
|
|
|
|
|
| |||
|
|
|
|
|
| halfduplex protocol; default DM rate |
|
|
| |
|
|
|
|
|
| fixed at 115200 bps |
|
|
|
|
|
|
|
|
|
| Changes DM rate that will be used on |
|
|
| |
|
|
|
|
|
| mobile’s serial port when mobile’s |
|
|
| |
|
|
|
|
|
| serial port transitions to DM mode; DM |
|
|
| |
| $QCDMR= |
|
|
|
| mode is entered after $QCDMG |
|
|
| |
|
|
| set DM baud rate |
| command is issued; default DM rate is |
| Supported |
| ||
| <rate> |
|
|
| fixed at 115200 bps; test command, |
|
| |||
|
|
|
|
|
|
|
| |||
|
|
|
|
|
| i.e., $QCDMR=?, returns rates |
|
|
| |
|
|
|
|
|
| supported and query command, i.e., |
|
|
| |
|
|
|
|
|
| $QCDMR?, returns current |
|
|
|
|
|
|
|
|
|
| Rate |
|
|
|
|
|
|
|
| dump configuration |
| Dumps the status of all AT parameters |
|
|
| |
| &V |
|
|
| applicable to current operating mode, |
| Supported |
| ||
|
|
| parameters |
| including the |
|
| |||
|
|
|
|
|
|
|
| |||
|
|
|
|
|
| not otherwise readable |
|
|
|
|
|
|
|
| Circuit 109 (carrier |
| Setting “winks” (briefly transitions off, |
|
|
| |
|
|
|
| detect pin) behavior - |
|
|
|
| ||
| &C2 |
|
|
| then back on) the Rm port Carrier |
| Supported |
| ||
|
|
| wink |
|
|
| ||||
|
|
|
|
| Detect pin when Data calls end |
|
|
| ||
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| Sets |
|
|
| |
|
|
|
| Set |
| accept commands; this data rate also |
|
|
| |
|
|
|
|
| becomes the default and is stored in |
|
|
| ||
| $QCTER= |
|
| Baud rates supported |
| NV RAM, changing the +IPR |
| Supported |
| |
|
|
| are identical to +IPR |
| command default rate; test command, |
|
| |||
| <rate> |
|
|
|
|
| ||||
|
|
| command. |
| i.e., $QCTER=?, returns rates |
|
|
| ||
|
|
|
|
|
|
|
| |||
|
|
|
|
|
| supported and query command, i.e., |
|
|
| |
|
|
|
|
|
| $QCTER?, returns rate last issued by |
|
|
| |
|
|
|
|
|
| $QCTER command or default rate |
|
|
| |
|
|
|
|
|
| Sets the default primary IP address |
|
|
| |
|
|
|
|
|
| used for Domain Name Services; |
|
|
| |
| $ $QCDNSP= |
|
| set primary DNS IP address | used only if no DNS server address is |
| Supported |
| ||
| <address> |
|
| received over the air during PDP |
|
| ||||
|
|
|
|
|
|
|
| |||
|
|
|
|
|
| context activation; value is stored in |
|
|
| |
|
|
|
|
|
| NVRAM. |
|
|
|
|
|
|
|
|
|
| Sets the default secondary IP address |
|
|
| |
| $QCDNSS= |
|
|
|
| used for Domain Name Services; |
|
|
| |
|
|
| Set secondary DNS IP |
| used only if no DNS server address is |
| Supported |
| ||
| <address> |
|
| address |
| received over the air during PDP |
|
| ||
|
|
|
|
|
|
| ||||
|
|
|
|
|
| context activation; value is stored in |
|
|
| |
|
|
|
|
|
| NVRAM |
|
|
|
|
| $QCPDPP= |
|
| Defines authentication parameters on |
|
|
| |||
| <cid>, |
|
| <cid> – 1 to 16 |
| a per connection basis. Value of |
| Supported |
| |
| <auth_type>, |
| <auth_type>: |
| <auth_type> determines what |
|
|
| ||
| HSDPA Standard At Commands | Page 59 of 60 | Version 1.2 |
|
|