Maxon Telecom MM-6280IND manual Define PDP Context +CGDCONT, +CGDCONT parameter command syntax

Page 38

	+CGANS		Opt.	Manual response to a network request for PDP context	Not supported
	+CGANS		Opt.	activation	Not supported
				activation
	+CGCLASS		Opt.	GPRS mobile station class	Supported
	+CGCLPAD		Opt.	Configure local triple-X PAD parameters	Not supported
	(GPRS only)				Not supported
	(GPRS only)
	+CGEREP		Opt.	Packet Domain event reporting	Supported
	+CGREG		Opt.	GPRS network registration status	Supported
	+CGSMS		Opt.	Select service for MO SMS messages	Supported

1.32.1.Define PDP Context +CGDCONT

The set command specifies PDP context parameter values for a PDP context identified by the (local) context identification parameter, <cid>. The number of PDP contexts that may be in a defined state at the same time is given by the range returned by the test command.

A special form of the set command, +CGDCONT= <cid> causes the values for context number <cid> to become undefined.

The read command returns the current settings for each defined context.

The test command returns values supported as a compound value. If the MT supports several PDP types, <PDP_type>, the parameter value ranges for each <PDP_type> are returned on a separate line.

Table 28. +CGDCONT parameter command syntax

Command

Possible response(s)

+CGDCONT=[<cid> OK [,<PDP_type> [,<APN> ERROR [,<PDP_addr> ,<d_comp>[,<h_comp> [,<pd1> [,…[,pdN]]]]]]]]]

+CGDCONT?		+CGDCONT: <cid>, <PDP_type>,
		<APN>,<PDP_addr>,<d_comp>, <h_comp>[,<pd1>[,…[,pdN]]]
		[<CR><LF>+CGDCONT:<cid>,<PDP_type>,		<APN>,<PDP_addr>,<d_comp>,
		<h_comp>[,<pd1>[,…[,pdN]]]
		[...]]
+CGDCONT=?		+CGDCONT: (range of supported <cid>s), <PDP_type>,,,(list of supported
		<d_comp>s),
		(list of supported <h_comp>s)[,(list of supported <pd1>s)[,…[,(list of
		supported <pdN>s)]]]
		[<CR><LF>+CGDCONT: (range of supported <cid>s), <PDP_type>,,,(list of
		supported <d_comp>s),
		(list of supported <h_comp>s)[,(list of supported <pd1>s)[,…[,(list of
		supported <pdN>s)]]]
		[...]]
Value		<cid>: (PDP Context Identifier) a numeric parameter which specifies a particular PDP
Value		context definition. The parameter is local to the TE-MT interface and is used in other
		PDP context-related commands. The range of permitted values (minimum value = 1) is

	HSDPA Standard At Commands		Page 38 of 60	Version 1.2

Image 38

Contents Hsdpa Standard AT Commands Manual Document Description Revision History Contact Information Table of Contents Qualcomm commands Terms IntroductionGeneral Terms definitionReferences 3GPP TSITU-T Recommendation T.31 GSM MoU SE.13ITU-T Recommendation E.212 ITU-T Recommendation T.32Etsi TS 102 Ccitt RecommendationITU-T Recommendation RFC 3748, JuneBasic Integration Command FormatAT command Format Serial InterfaceTE2 MT2 DTE-TA/DCE interface commandsMT2 TE2 +IFC +ICFTE2-MT2 +ILRR Mobile Termination error result code CME Error Mobile Termination errors commandsReport Mobile Termination error +CMEE +CMEE parameter command syntaxHsdpa Standard At Commands Informative examples AT+CGMI Error AT+CMEE=1AT+CGMI +CME Error AT+CMEE=2 AT+CMEE=0Request model identification+CGMM General commandsRequest manufacturer identification+CGMI +CSCS parameter command syntax +CGMM action command syntax+CGSN action command syntax Request product serial number identification +CGSNITU-T V.250 generic TA control commands Pcca STD‑101 17 select wireless network +WS46 Supported alphabets Network service commands Network registration +CREG +CNUM action command syntaxSubscriber number +CNUM +CNUM+CREG? +CREG parameter command syntaxPlmn selection +COPS +CREG=?Applicable in read command response When mode=2 and command successful Facility lock +CLCKUnlock Lock Query status Preferred Plmn list +CPOL Change password +CPWD+CPWD action command syntax Read operator names +COPN +COLP parameter command syntax+COPN action command syntax Operator information readingNetwork registration Imsi number readingGprs Attachment Own number readingBasic TE Mobile Termination control and status commandsBasic TE +CCLK parameter command syntax Signal quality +CSQ+CSQ action command syntax Clock +CCLK+CPIN parameter command syntax AT$$MBAND Read CommandAT$$MBAND Write Command Band Selection AT$$MBAND Signal strength reading PH-SIM PINPin registration Umts packet Domain commands Command Req Description Support Packet Domain CommandGPRSUmts packet Domain commands +CGDCONT? +CGDCONT parameter command syntaxDefine PDP Context +CGDCONT +CGDCONT=?Define Secondary PDP Context +CGDSCONT PPP+CGDSCONT? ErrorTraffic Flow Template +CGTFT + Cgtft parameter command syntax +CGTFT? +CGTFT=? Quality of Service Profile Requested +CGQREQ + Cgqreq parameter command syntaxQuality of Service Profile Minimum acceptable +CGQMIN + Cgqmin parameter command syntaxCRLF+CGQMIN Quality of Service Profile Requested +CGEQREQ+ Cgeqreq parameter command syntax SDU+CGEQREQ? +CGEQREQ=?Subscribed value. Other values are reserved Quality of Service Profile Minimum acceptable +CGEQMIN PDPtype see +CGDCONT and +CGDSCONT commandsCRLF+CGEQMIN + Cgeqmin parameter command syntax+CGEQMIN? +CGEQMIN=?Following parameters are defined in 3GPP TS 23.107 Quality of Service Profile Negotiated +CGEQNEG +CGEQNEG=? +CGEQNEG action command syntax+CGEQNEG PS attach or detach +CGATT PDP context activate or deactivate +CGACT + Cgatt parameter command syntax+ Cgact parameter command syntax Enter data state +CGDATA + Cgcmod parameter command syntaxPDP Context Modify +CGCMOD +CGCMOD=?+ Cgdata parameter command syntax Show PDP address +CGPADDRUmts Connection Modem compatibility commands+ Cgpaddr parameter command syntax +CGPADDR=?Synchronous data mode commands Description Operation Support Qualcomm commandsQualcomm command $QCDGEN= $QCPINSTAT$QCPWRDN $QCSLOT=

Related manuals

Manual 70 pages 35.54 Kb