Maxon Telecom MM-6280IND manual Subscribed value. Other values are reserved

Page 47

3 - background

4 - subscribed value

If the Traffic class is specified as conversational or streaming, then the Guaranteed and Maximum bitrate parameters should also be provided. Other values are reserved.

<Maximum bitrate UL>: a numeric parameter that indicates the maximum number of kbits/s delivered to UMTS (up-link traffic) at a SAP. As an example a bitrate of 32kbit/s would be specified as '32' (e.g. AT+CGEQREQ=…,32, …). This parameter should be provided if the Traffic class is specified as conversational or streaming (refer TS 24.008 [8] subclause 10.5.6.5).

<Maximum bitrate DL>: a numeric parameter that indicates the maximum number of kbits/s delivered by UMTS (down-link traffic) at a SAP. As an example a bitrate of 32kbit/s would be specified as '32' (e.g. AT+CGEQREQ=…,32, …). If the parameter is set to '0' the subscribed value will be requested. This parameter should be provided if the Traffic class is specified as conversational or streaming (refer TS 24.008 [8] subclause 10.5.6.5).

<Guaranteed bitrate UL>: a numeric parameter that indicates the guaranteed number of kbits/s delivered to UMTS (up-link traffic) at a SAP (provided that there is data to deliver). As an example a bitrate of 32kbit/s would be specified as '32' (e.g. AT+CGEQREQ=…,32, …). If the parameter is set to '0' the subscribed value will be requested. This parameter should be provided if the Traffic class is specified as conversational or streaming (refer TS 24.008 [8] subclause 10.5.6.5).

<Guaranteed bitrate DL>: a numeric parameter that indicates the guaranteed number of kbits/s delivered by UMTS (down-link traffic) at a SAP (provided that there is data to deliver). As an example a bitrate of 32kbit/s would be specified as '32' (e.g. AT+CGEQREQ=…,32, …). If the parameter is set to '0' the subscribed value will be requested. This parameter should be provided if the Traffic class is specified as conversational or streaming (refer TS 24.008 [8] subclause 10.5.6.5).

<Delivery order>: a numeric parameter that indicates whether the UMTS bearer shall provide in-sequence SDU delivery or not.

0 - no

1 - yes

2 - subscribed value. Other values are reserved.

<Maximum SDU size>: a numeric parameter (1,2,3,…) that indicates the maximum allowed SDU size in octets. If the parameter is set to '0' the subscribed value will be requested (refer TS 24.008 [8] subclause 10.5.6.5).

<SDU error ratio>: a string parameter that indicates the target value for the fraction of SDUs lost or detected as erroneous. SDU error ratio is defined only for conforming traffic. The value is specified as 'mEe'. As an example a target SDU error ratio of 5•10-3would be specified as '5E3' (e.g. AT+CGEQREQ=…,”5E3”,…). '0E0' means subscribed value (refer TS 24.008 [8] subclause 10.5.6.5).

<Residual bit error ratio>: a string parameter that indicates the target value for the undetected bit error ratio in the delivered

HSDPA Standard At Commands

Page 47 of 60

Version 1.2

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Hsdpa Standard AT Commands Manual Document Description Revision History Contact Information Table of Contents Qualcomm commands Terms definition IntroductionGeneral Terms3GPP TS ReferencesITU-T Recommendation T.32 GSM MoU SE.13ITU-T Recommendation E.212 ITU-T Recommendation T.31RFC 3748, June Ccitt RecommendationITU-T Recommendation Etsi TS 102Serial Interface Command FormatAT command Format Basic IntegrationTE2 MT2 DTE-TA/DCE interface commandsMT2 TE2 +IFC +ICFTE2-MT2 +ILRR +CMEE parameter command syntax Mobile Termination errors commandsReport Mobile Termination error +CMEE Mobile Termination error result code CME ErrorHsdpa Standard At Commands AT+CMEE=0 AT+CGMI Error AT+CMEE=1AT+CGMI +CME Error AT+CMEE=2 Informative examplesRequest model identification+CGMM General commandsRequest manufacturer identification+CGMI Request product serial number identification +CGSN +CGMM action command syntax+CGSN action command syntax +CSCS parameter command syntaxITU-T V.250 generic TA control commands Pcca STD‑101 17 select wireless network +WS46 Supported alphabets Network service commands +CNUM +CNUM action command syntaxSubscriber number +CNUM Network registration +CREG+CREG=? +CREG parameter command syntaxPlmn selection +COPS +CREG?Applicable in read command response Facility lock +CLCK When mode=2 and command successfulUnlock Lock Query status Preferred Plmn list +CPOL Change password +CPWD+CPWD action command syntax Operator information reading +COLP parameter command syntax+COPN action command syntax Read operator names +COPNOwn number reading Imsi number readingGprs Attachment Network registrationBasic TE Mobile Termination control and status commandsBasic TE Clock +CCLK Signal quality +CSQ+CSQ action command syntax +CCLK parameter command syntaxBand Selection AT$$MBAND AT$$MBAND Read CommandAT$$MBAND Write Command +CPIN parameter command syntaxPH-SIM PIN Signal strength readingPin registration Umts packet Domain commands Command Req Description Support Packet Domain CommandGPRSUmts packet Domain commands +CGDCONT=? +CGDCONT parameter command syntaxDefine PDP Context +CGDCONT +CGDCONT?PPP Define Secondary PDP Context +CGDSCONT+CGDSCONT? ErrorTraffic Flow Template +CGTFT + Cgtft parameter command syntax +CGTFT? +CGTFT=? + Cgqreq parameter command syntax Quality of Service Profile Requested +CGQREQ + Cgqmin parameter command syntax Quality of Service Profile Minimum acceptable +CGQMINSDU Quality of Service Profile Requested +CGEQREQ+ Cgeqreq parameter command syntax CRLF+CGQMIN+CGEQREQ=? +CGEQREQ?Subscribed value. Other values are reserved PDPtype see +CGDCONT and +CGDSCONT commands Quality of Service Profile Minimum acceptable +CGEQMIN+CGEQMIN=? + Cgeqmin parameter command syntax+CGEQMIN? CRLF+CGEQMINFollowing parameters are defined in 3GPP TS 23.107 Quality of Service Profile Negotiated +CGEQNEG +CGEQNEG=? +CGEQNEG action command syntax+CGEQNEG PS attach or detach +CGATT PDP context activate or deactivate +CGACT + Cgatt parameter command syntax+ Cgact parameter command syntax +CGCMOD=? + Cgcmod parameter command syntaxPDP Context Modify +CGCMOD Enter data state +CGDATAShow PDP address +CGPADDR + Cgdata parameter command syntax+CGPADDR=? Modem compatibility commands+ Cgpaddr parameter command syntax Umts ConnectionSynchronous data mode commands Description Operation Support Qualcomm commandsQualcomm command $QCSLOT= $QCPINSTAT$QCPWRDN $QCDGEN=
Related manuals
Manual 70 pages 35.54 Kb
Top Page Image Contents