RAD Data comm ASMI-450 operation manual Off

Page 36
Upon first-time operation, you should use the ON position to start the configuration. You can select this position again to restart with the default parameters in case the current values are not known, and it is not possible to communicate with the ASMi-450 through its control port.
The ASMi-450 is shipped with this section set at OFF.
Switch section DB INT. This section selects the source of the data base configuration parameters:
OFF
ASMi-450 uses the user-selected parameters.
ON
ASMi-450 uses the default parameters stored in its program EPROM. The default values are Autobaud, eight data bits, and no parity.
DIP switch S1 allows the user to control the reloading of the desired group of default parameters. The switch has four sections used for the following purposes:
Switch section DEF SP. This section selects the source of the control port parameters:

Installation

ON

ASMi-450 uses the default parameters stored in its program

 

EPROM.

OFF

ASMi-450 uses the user-selected parameters.

The ASMi-450 is delivered with the data base loaded with the default parameters. You can select this position again to restart with the default parameters in case the current values are not known.

The ASMi-450 is shipped with this section set at OFF.

Switch section MS/SV. This section is reserved for future features, and must be always set at ON.

The ASMi-450 is shipped with this section set at ON.

Switch section PSWD. A password, consisting of up to eight alphanumeric characters, can be used to prevent unauthorized personnel from using the ASMi-450 control program. The ASMi-450 is delivered with a default password, ASMI, but normally the password is selected by the user.

The PSWD section is used to select between the default ASMi-450 password (the ON position) and the user-selected password (the OFF position). The ASMi-450 address (node number) is also affected by the setting of the PSWD section: with the jumper set at ON, the node number is set to 0.

Upon first-time operation, you should use the ON position to start the configuration. You can select this position again to restart with the default password and node address 0 in case the current user password was lost.

The ASMi-450 is shipped with this section set at OFF.

2-6

ASMi-450 Installation and Operation Manual

Image 36
Contents ASMi-450 Warranty Selv HdslRegulatory Information Declaration of Conformity Page Contents ASMi-450 Control from the Control Port Appendix a Connector Wiring Contents List of Figures List of Figures Xii List of Tables List of Tables Xiv Starting the Configuration Preliminary Preparations Starting ProcedureConfiguration Procedure Step Action Use the CommandFunction Terminal Type TV920 VT52 VT100 Freedom 100/110 Command Index Type Configuration Display Commands Control CommandsQuick-Start Guide Purpose and Main Features Functional DescriptionTypical Application for ASMi-450 with Data Interface Hdsl Subsystem Characteristics System Timing Internal timingControl ASMi-450 Operation Local ControlRemote Management Introduction Test and Diagnostics Capabilities AlarmsPhysical Characteristics Power RequirementsTransmission Media Hdsl Line Signal Binary Digits Quaternary SymbolOperating Environment Hdsl Signal Structure HDSL-Related System Functions Technical Specifications Hdsl InterfaceEthernet Interface Physical Characteristics Chapter Installation GeneralUnpacking Site RequirementsASMi-450 Configuration Information GeneralOpening ASMi-450 Case Jumper and Switch Location Functions Switch S1ASMi-450 Internal Settings OFF Internal Settings Procedure Reinstalling ASMi-450 Cover Jumper R/CJumper FGND/GND Connector Location Grounding Power Connection Users Port Connections AC Power ConnectionDC Power Connection Hdsl Line Connections Control Port Connection Chapter Front-Panel Operating Instructions ScopeFront Panel Controls, Connectors, and Indicators Control or Indicator FunctionIndicators Indicator FunctionEthernet Interface Control of ASMi-450 Operation, General General General Operating Instructions Display FunctionsConfiguration Parameters Status MessagesTest Functions Display Description SeeUsing Front-Panel OrganizationASMi-450 Display Push-buttonsFront-Panel Operating Instructions System Configuration Parameters Designation Function ValuesControl Port Configuration Parameters Turn-on Checking Current Operating Configuration Operating InstructionsDisplay CursorScroll Fault Indications Step Action Key DisplayNormal Front-Panel Indications Ethernet Interface IndicationsLocal Configuration Set-Up Procedure PasswordConfiguration Procedure ProtectionAlready there Scroll to display the desired group Specific Configuration Guidelines Alarm BufferSP Parameters LCD Configuration Error Messages Front-Panel Operating Instructions Chapter ASMi-450 Control from the Control Port Hardware Requirements Interface Type Data Terminal Ready DTRRequest to Send RTS Clear to Send CTSAutobaud Function Ring Indication RIData Set Ready DSR Internal Settings Control Port ConfigurationPreparation for Use of Supervision Terminal ASMi-450 Preparations Supervision Terminal ConnectionsCommand Language Syntax Command Options Command ProtocolASMi-450 Supervision Language Option Meaning Example of UsageIndex of Commands Command Purpose Options ASMi-450 Command Set Description CLR ALMCLR Loop FormatCLR TST DateDEF Agent DEF Name Display FieldsDEF Node DEF PWDDEF SP Purpose Format UsePWD DEF SYS DEF TermDSP ALM Function Terminal Type VT-52 VT-100 Freedom-110Format Use Alarm No Alarm Syntax Meaning State Time Remote Alarm Remote Signal LossQuality Alarm Remote DBDSP HDR TST DSP ST LineREM LAN not ConnectedDSP ST Port Display FormatPurpose Format Use Display Format DSP ST SYS ExitHelp Parameter Designation Default Value Init DBPassword LoopNode Reset TimeStarting a Session Single ASMi-450 Control Session Ending a Control Session Configuration Error Messages ASMi-450 Control from the Control Port Indicators Display Status Indications and MessagesMessage Description Corrective Actions Alarm ON/OFFASMi-450 Alarm Buffer Messages Cont’d Remote Alarm Remote Reverse Test Functions Test FunctionsLoop REM REM Port Operating InstructionsPower-Up Self-Test Activating the Test Functions from a Control TerminalTroubleshooting Instructions Trouble Symptoms Probable Cause Corrective MeasuresLAN RS-530 DCE Connector and Adapter Cables Pin Designation Direction FunctionPin Designation Direction Function 36/RS-449/422 RceaRceb V.35 DCE Connector X.21 DCE Connector Hdsl Line Connector RS-232 V.24 Control Port ConnectorPin Function Pin Line Connected Connected to To TerminalEthernet Interface Connector Appendix B Snmp Management Snmp Environment General Snmp PrinciplesSnmp Operations Management Information Base MIB StructureMIBs Supported by the ASMi-450 Snmp Agent Access Restriction Using Snmp Communities Management Domains UnderSnmp Communities ASMi-450 Communities ReadIP Environment General IP EnvironmentIP Address Structure Address Class First Byte Address RangeSnmp Management Snmp Traps Appendix C Installation in 19 Racks Installation of Single Unit Figure C-1. Installation of Single Unit in 19 RackInstallation of Two Units General PreparationsFastening the Two Units To install the ferrite cores ASMi-450