RAD Data comm ASMI-450 operation manual Def Sys, DEF Term

Page 73

ASMi-450 Control from the Control Port

DEF SYS---------------------------------------------------------------------------------------

Purpose

Assign values to system parameters.

 

 

Format

DEF SYS

 

 

 

Use

1. Type

 

 

 

 

DEF SYS<CR>

 

 

 

 

2. The system parameters data form is displayed. A typical form for an ASMi-450/1152

 

with Ethernet interface is shown below. The form presents the current parameter

 

values as defaults. For ASMi-450 with serial data port, the ETHERNET_MODE and

 

BRIDGING fields always show N/A.

 

 

 

CLK_MASTER ACTIVE_TS

ETHERNET_MODE

BRIDGING

 

EXT

18

HALF_DUP

FILTER

See Section 3-4 for a description of the various parameters, and Section 3-7 for practical selection recommendations.

3.Change the parameter values as follows:

Bring the cursor to the beginning of the first field to be changed by pressing the space bar.

To change the selected field, press F or B to scroll among the available selections.

When the desired selection is displayed, press the space bar to move to the next field.

4.After the desired parameter values are selected, press <CR> to end. The ASMi-450 will display the TIME and DATE fields, followed by the ASMi-450 prompt.

DEF TERM ------------------------------------------------------------------------------------

Purpose

Define the control sequences to be sent to the supervision terminal to perform the

 

following terminal control functions:

 

∙ Clear screen.

 

∙ Move cursor to screen home position.

 

∙ Move cursor to the right by one position.

 

This command is similar to the F command (see F section below), except that it also

 

enables you to specify a terminal type and the ASMi-450 will automatically configure

 

itself for using the corresponding control sequences. The terminal types supported by

 

this command are: VT-52, VT-100, TV-920, FREEDOM-100, FREEDOM-110,

 

FREEDOM-220, and terminals compatible with one of them.

 

The codes used by the supported terminals are listed in the following chart:

ASMi-450 Installation and Operation Manual

4-15

Image 73
Contents ASMi-450 Warranty Hdsl SelvRegulatory Information Declaration of Conformity Page Contents ASMi-450 Control from the Control Port Appendix a Connector Wiring Contents List of Figures List of Figures Xii List of Tables List of Tables Xiv Preliminary Preparations Starting Procedure Starting the ConfigurationStep Action Use the Command Configuration ProcedureFunction Terminal Type TV920 VT52 VT100 Freedom 100/110 Type Configuration Display Commands Control Commands Command IndexQuick-Start Guide Functional Description Purpose and Main FeaturesTypical Application for ASMi-450 with Data Interface Hdsl Subsystem Characteristics Internal timing System TimingLocal Control Control ASMi-450 OperationRemote Management Introduction Alarms Test and Diagnostics CapabilitiesPhysical Characteristics Power RequirementsBinary Digits Quaternary Symbol Transmission Media Hdsl Line SignalOperating Environment Hdsl Signal Structure HDSL-Related System Functions Hdsl Interface Technical SpecificationsEthernet Interface Physical Characteristics General Chapter InstallationSite Requirements UnpackingGeneral ASMi-450 Configuration InformationOpening ASMi-450 Case Switch S1 Jumper and Switch Location FunctionsASMi-450 Internal Settings OFF Jumper R/C Internal Settings Procedure Reinstalling ASMi-450 CoverJumper FGND/GND Connector Location Grounding AC Power Connection Power Connection Users Port ConnectionsDC Power Connection Hdsl Line Connections Control Port Connection Scope Chapter Front-Panel Operating InstructionsControl or Indicator Function Front Panel Controls, Connectors, and IndicatorsIndicator Function IndicatorsEthernet Interface General General Operating Instructions Display Functions Control of ASMi-450 Operation, GeneralStatus Messages Configuration ParametersTest Functions Display Description SeeOrganization Using Front-PanelASMi-450 Display Push-buttonsFront-Panel Operating Instructions Designation Function Values System Configuration ParametersControl Port Configuration Parameters Operating Instructions Turn-on Checking Current Operating ConfigurationCursor DisplayScroll Step Action Key Display Fault IndicationsNormal Front-Panel Indications Ethernet Interface IndicationsPassword Local Configuration Set-Up ProcedureConfiguration Procedure ProtectionAlready there Scroll to display the desired group Alarm Buffer Specific Configuration GuidelinesSP Parameters LCD Configuration Error Messages Front-Panel Operating Instructions Chapter ASMi-450 Control from the Control Port Hardware Requirements Data Terminal Ready DTR Interface TypeRequest to Send RTS Clear to Send CTSRing Indication RI Autobaud FunctionData Set Ready DSR Control Port Configuration Internal SettingsPreparation for Use of Supervision Terminal ASMi-450 Preparations Supervision Terminal ConnectionsCommand Protocol Command Language Syntax Command OptionsASMi-450 Supervision Language Option Meaning Example of UsageIndex of Commands Command Purpose Options CLR ALM ASMi-450 Command Set DescriptionCLR Loop FormatDate CLR TSTDEF Agent Display Fields DEF NameDEF PWD DEF NodePurpose Format Use DEF SPPWD DEF Term DEF SYSFunction Terminal Type VT-52 VT-100 Freedom-110 DSP ALMFormat Use Alarm No Alarm Syntax Meaning State Time Remote Signal Loss Remote AlarmQuality Alarm Remote DBDSP ST Line DSP HDR TSTREM LAN not ConnectedDisplay Format DSP ST PortPurpose Format Use Display Format Exit DSP ST SYSHelp Init DB Parameter Designation Default ValueLoop PasswordNode Time ResetStarting a Session Single ASMi-450 Control Session Ending a Control Session Configuration Error Messages ASMi-450 Control from the Control Port Status Indications and Messages Indicators DisplayON/OFF Message Description Corrective Actions AlarmASMi-450 Alarm Buffer Messages Cont’d Remote Alarm Remote Reverse Test Functions Test FunctionsOperating Instructions Loop REM REM PortActivating the Test Functions from a Control Terminal Power-Up Self-TestTrouble Symptoms Probable Cause Corrective Measures Troubleshooting InstructionsLAN Pin Designation Direction Function RS-530 DCE Connector and Adapter CablesRcea Pin Designation Direction Function 36/RS-449/422Rceb V.35 DCE Connector X.21 DCE Connector RS-232 V.24 Control Port Connector Hdsl Line ConnectorPin Function Pin Line Connected Connected to To TerminalEthernet Interface Connector Appendix B Snmp Management General Snmp Principles Snmp EnvironmentSnmp Operations MIB Structure Management Information BaseMIBs Supported by the ASMi-450 Snmp Agent Management Domains Under Access Restriction Using Snmp CommunitiesSnmp Communities Read ASMi-450 CommunitiesGeneral IP Environment IP EnvironmentIP Address Structure Address Class First Byte Address RangeSnmp Management Snmp Traps Appendix C Installation in 19 Racks Figure C-1. Installation of Single Unit in 19 Rack Installation of Single UnitGeneral Preparations Installation of Two UnitsFastening the Two Units ASMi-450 To install the ferrite cores