RAD Data comm ASMI-450 Step Action Key Display, Normal Front-Panel Indications, Fault Indications

Page 52
For DC-poweredASMi-450 units, disconnect the power cable.
ASMi-450 Installation and Operation Manual

Front-Panel Operating Instructions

In Table 5-1, you will find two types of alarms, designated as ON/OFF and ON:

A message indicating an ON/OFF alarm is displayed only when the alarm condition is present, and is automatically removed when the condition is cleared (if the alarm is being displayed, it will disappear only when the display is refreshed by scrolling).

A message indicating an ON alarm persists even after the event that caused the alarm condition is cleared.

If the ASMi-450 operates normally, but an alarm message of the ON type is displayed, you can clear the event alarm message from the display by the following procedure:

Step

Action

Key

Display

 

 

 

 

 

 

 

 

1

Bring the cursor in the second row, under

CURSOR

 

 

CLEAR

 

 

2

Press ENTER to clear the event messages in

ENTER

If no state alarms are present, the second row

 

the alarm buffer

 

should show EMPTY

 

 

 

 

 

Normal Front-Panel Indications

 

During normal operation, all the ASMi-450 front-panel indicators are off.

 

Ethernet Interface Indications

 

During normal operation, the LINK indicator must light continuously. The

 

COLL, TX, and RX light according to LAN traffic conditions.

Fault Indications

If the LOS indicator and/or the TST indicator lights, data transfer is interrupted.

 

∙ The TST indicator lights when a test is active. If the test is activated from

 

the local ASMi-450, you can see the test type by entering the TEST

 

OPTIONS (Chapter 5). You can disconnect a local or remote loop as

 

explained in Chapter 5.

 

∙ The HDSL LOS indicator lights when a local loss of synchronization alarm

 

condition is present on the corresponding line.

 

∙ When using the Ethernet interface, the rear LINK indicator will turn off if

 

the Ethernet LAN is not connected, or not operating properly.

 

If the COLL indicator lights continuously, this indicates that a permanent

 

state of collision is present on the LAN. This may be caused by

 

malfunctioning LAN equipment, however it may also occur in case a test

 

loopback is activated on the ASMi-450. Check and deactivate any test

 

loopback on the local and remote ASMi-450 units.

Turn-off

For AC-powered ASMi-450 units, set the rear power switch to OFF.

3-12

Image 52
Contents ASMi-450 Warranty Selv HdslRegulatory Information Declaration of Conformity Page Contents ASMi-450 Control from the Control Port Appendix a Connector Wiring Contents List of Figures List of Figures Xii List of Tables List of Tables Xiv Starting the Configuration Preliminary Preparations Starting ProcedureStep Action Use the Command Configuration ProcedureFunction Terminal Type TV920 VT52 VT100 Freedom 100/110 Command Index Type Configuration Display Commands Control CommandsQuick-Start Guide Purpose and Main Features Functional DescriptionTypical Application for ASMi-450 with Data Interface Hdsl Subsystem Characteristics System Timing Internal timingLocal Control Control ASMi-450 OperationRemote Management Introduction Test and Diagnostics Capabilities AlarmsPhysical Characteristics Power RequirementsBinary Digits Quaternary Symbol Transmission Media Hdsl Line SignalOperating Environment Hdsl Signal Structure HDSL-Related System Functions Technical Specifications Hdsl InterfaceEthernet Interface Physical Characteristics Chapter Installation GeneralUnpacking Site RequirementsGeneral ASMi-450 Configuration InformationOpening ASMi-450 Case Jumper and Switch Location Functions Switch S1ASMi-450 Internal Settings OFF Jumper R/C Internal Settings Procedure Reinstalling ASMi-450 CoverJumper FGND/GND Connector Location Grounding AC Power Connection Power Connection Users Port ConnectionsDC Power Connection Hdsl Line Connections Control Port Connection Chapter Front-Panel Operating Instructions ScopeFront Panel Controls, Connectors, and Indicators Control or Indicator FunctionIndicator Function IndicatorsEthernet Interface Control of ASMi-450 Operation, General General General Operating Instructions Display FunctionsConfiguration Parameters Status MessagesTest Functions Display Description SeeUsing Front-Panel OrganizationASMi-450 Display Push-buttonsFront-Panel Operating Instructions System Configuration Parameters Designation Function ValuesControl Port Configuration Parameters Turn-on Checking Current Operating Configuration Operating InstructionsCursor DisplayScroll Fault Indications Step Action Key DisplayNormal Front-Panel Indications Ethernet Interface IndicationsLocal Configuration Set-Up Procedure PasswordConfiguration Procedure ProtectionAlready there Scroll to display the desired group Specific Configuration Guidelines Alarm BufferSP Parameters LCD Configuration Error Messages Front-Panel Operating Instructions Chapter ASMi-450 Control from the Control Port Hardware Requirements Interface Type Data Terminal Ready DTRRequest to Send RTS Clear to Send CTSRing Indication RI Autobaud FunctionData Set Ready DSR Internal Settings Control Port ConfigurationPreparation for Use of Supervision Terminal ASMi-450 Preparations Supervision Terminal ConnectionsCommand Language Syntax Command Options Command ProtocolASMi-450 Supervision Language Option Meaning Example of UsageIndex of Commands Command Purpose Options ASMi-450 Command Set Description CLR ALMCLR Loop FormatDate CLR TSTDEF Agent DEF Name Display FieldsDEF Node DEF PWDDEF SP Purpose Format UsePWD DEF SYS DEF TermFunction Terminal Type VT-52 VT-100 Freedom-110 DSP ALMFormat Use Alarm No Alarm Syntax Meaning State Time Remote Alarm Remote Signal LossQuality Alarm Remote DBDSP HDR TST DSP ST LineREM LAN not ConnectedDisplay Format DSP ST PortPurpose Format Use Display Format DSP ST SYS ExitHelp Parameter Designation Default Value Init DBLoop PasswordNode Reset TimeStarting a Session Single ASMi-450 Control Session Ending a Control Session Configuration Error Messages ASMi-450 Control from the Control Port Indicators Display Status Indications and MessagesMessage Description Corrective Actions Alarm ON/OFFASMi-450 Alarm Buffer Messages Cont’d Remote Alarm Remote Reverse Test Functions Test FunctionsLoop REM REM Port Operating InstructionsPower-Up Self-Test Activating the Test Functions from a Control TerminalTroubleshooting Instructions Trouble Symptoms Probable Cause Corrective MeasuresLAN RS-530 DCE Connector and Adapter Cables Pin Designation Direction FunctionRcea Pin Designation Direction Function 36/RS-449/422Rceb V.35 DCE Connector X.21 DCE Connector Hdsl Line Connector RS-232 V.24 Control Port ConnectorPin Function Pin Line Connected Connected to To TerminalEthernet Interface Connector Appendix B Snmp Management General Snmp Principles Snmp EnvironmentSnmp Operations MIB Structure Management Information BaseMIBs Supported by the ASMi-450 Snmp Agent Management Domains Under Access Restriction Using Snmp CommunitiesSnmp Communities ASMi-450 Communities ReadIP Environment General IP EnvironmentIP Address Structure Address Class First Byte Address RangeSnmp Management Snmp Traps Appendix C Installation in 19 Racks Installation of Single Unit Figure C-1. Installation of Single Unit in 19 RackInstallation of Two Units General PreparationsFastening the Two Units To install the ferrite cores ASMi-450