RAD Data comm ASMI-450 Starting the Configuration, Preliminary Preparations Starting Procedure

Page 15

Quick-Start Guide

If you are familiar with HDSL transmission equipment, use this guide to prepare (configure) an ASMi-450 for operation. The configuration activities can be carried out either before or after the ASMi-450 is installed in its intended location.

Preliminary

Preparations

Starting Procedure

1. Starting the Configuration

To configure the ASMi-450, you need an ASCII terminal, e.g., a VT-100, etc., or a PC running a terminal emulation program. You also need a standard cable terminated in a 9-pin D-type male connector, for connecting the serial port of your terminal to the CONTROL DCE connector located on the front panel of the ASMi-450.

Configure your terminal for eight data bits, no parity, one stop bit, echo off, and no flow control. You can use 300, 1200, 2400, 4800, or 9600 bps - the ASMi-450 will automatically recognize the data rate you are using.

1.Turn the ASMi-450 on.

2.Connect the terminal cable to the CONTROL DCE connector of the ASMi-450.

3.Press the Carriage Return (<CR> or ENTER) key three times in sequence: you should see the ASMi-450 prompt, ASMI>.

If you see PASSWORD>, type ASMI and then press <CR> to obtain the prompt.

If you do not see the prompt:

∙Check the terminal configuration, and its connections to the ASMi-450, and then repeat step 3 above.

∙Turn the ASMi-450 off about 15 seconds, and then turn it on again and repeat step 3 above.

∙If this is the first time you are working on this ASMi-450 unit, refer to Section 4-3 for preliminary configuration instructions.

∙Read ASMi-450 display. If the second row shows EMPTY, everything is OK. If it shows SCROLL, press SCROLL and read the alarm messages. Refer to Chapter 5 for instructions.

ASMi-450 Installation and Operation Manual

Quick-Start Guide - 1

Image 15

Contents ASMi-450 Warranty Hdsl SelvRegulatory Information Declaration of Conformity Page Contents ASMi-450 Control from the Control Port Appendix a Connector Wiring Contents List of Figures List of Figures Xii List of Tables List of Tables Xiv Preliminary Preparations Starting Procedure Starting the ConfigurationConfiguration Procedure Step Action Use the CommandFunction Terminal Type TV920 VT52 VT100 Freedom 100/110 Type Configuration Display Commands Control Commands Command IndexQuick-Start Guide Functional Description Purpose and Main FeaturesTypical Application for ASMi-450 with Data Interface Hdsl Subsystem Characteristics Internal timing System TimingControl ASMi-450 Operation Local ControlRemote Management Introduction Power Requirements Test and Diagnostics CapabilitiesAlarms Physical CharacteristicsTransmission Media Hdsl Line Signal Binary Digits Quaternary SymbolOperating Environment Hdsl Signal Structure HDSL-Related System Functions Hdsl Interface Technical SpecificationsEthernet Interface Physical Characteristics General Chapter InstallationSite Requirements UnpackingASMi-450 Configuration Information GeneralOpening ASMi-450 Case Switch S1 Jumper and Switch Location FunctionsASMi-450 Internal Settings OFF Internal Settings Procedure Reinstalling ASMi-450 Cover Jumper R/CJumper FGND/GND Connector Location Grounding Power Connection Users Port Connections AC Power ConnectionDC Power Connection Hdsl Line Connections Control Port Connection Scope Chapter Front-Panel Operating InstructionsControl or Indicator Function Front Panel Controls, Connectors, and IndicatorsIndicators Indicator FunctionEthernet Interface General General Operating Instructions Display Functions Control of ASMi-450 Operation, GeneralDisplay Description See Configuration ParametersStatus Messages Test FunctionsPush-buttons Using Front-PanelOrganization ASMi-450 DisplayFront-Panel Operating Instructions Designation Function Values System Configuration ParametersControl Port Configuration Parameters Operating Instructions Turn-on Checking Current Operating ConfigurationDisplay CursorScroll Ethernet Interface Indications Fault IndicationsStep Action Key Display Normal Front-Panel IndicationsProtection Local Configuration Set-Up ProcedurePassword Configuration ProcedureAlready there Scroll to display the desired group Alarm Buffer Specific Configuration GuidelinesSP Parameters LCD Configuration Error Messages Front-Panel Operating Instructions Chapter ASMi-450 Control from the Control Port Hardware Requirements Clear to Send CTS Interface TypeData Terminal Ready DTR Request to Send RTSAutobaud Function Ring Indication RIData Set Ready DSR ASMi-450 Preparations Supervision Terminal Connections Internal SettingsControl Port Configuration Preparation for Use of Supervision TerminalOption Meaning Example of Usage Command Language Syntax Command OptionsCommand Protocol ASMi-450 Supervision LanguageIndex of Commands Command Purpose Options Format ASMi-450 Command Set DescriptionCLR ALM CLR LoopCLR TST DateDEF Agent Display Fields DEF NameDEF PWD DEF NodePurpose Format Use DEF SPPWD DEF Term DEF SYSDSP ALM Function Terminal Type VT-52 VT-100 Freedom-110Format Use Alarm No Alarm Syntax Meaning State Time Remote DB Remote AlarmRemote Signal Loss Quality AlarmConnected DSP HDR TSTDSP ST Line REM LAN notDSP ST Port Display FormatPurpose Format Use Display Format Exit DSP ST SYSHelp Init DB Parameter Designation Default ValuePassword LoopNode Time ResetStarting a Session Single ASMi-450 Control Session Ending a Control Session Configuration Error Messages ASMi-450 Control from the Control Port Status Indications and Messages Indicators DisplayON/OFF Message Description Corrective Actions AlarmASMi-450 Alarm Buffer Messages Cont’d Remote Alarm Remote Reverse Test Functions Test FunctionsOperating Instructions Loop REM REM PortActivating the Test Functions from a Control Terminal Power-Up Self-TestTrouble Symptoms Probable Cause Corrective Measures Troubleshooting InstructionsLAN Pin Designation Direction Function RS-530 DCE Connector and Adapter CablesPin Designation Direction Function 36/RS-449/422 RceaRceb V.35 DCE Connector X.21 DCE Connector Pin Line Connected Connected to To Terminal Hdsl Line ConnectorRS-232 V.24 Control Port Connector Pin FunctionEthernet Interface Connector Appendix B Snmp Management Snmp Environment General Snmp PrinciplesSnmp Operations Management Information Base MIB StructureMIBs Supported by the ASMi-450 Snmp Agent Access Restriction Using Snmp Communities Management Domains UnderSnmp Communities Read ASMi-450 CommunitiesAddress Class First Byte Address Range IP EnvironmentGeneral IP Environment IP Address StructureSnmp Management Snmp Traps Appendix C Installation in 19 Racks Figure C-1. Installation of Single Unit in 19 Rack Installation of Single UnitGeneral Preparations Installation of Two UnitsFastening the Two Units ASMi-450 To install the ferrite cores