RAD Data comm ASMI-450 Preparation for Use of Supervision Terminal, Internal Settings

Page 63

ASMi-450 Control from the Control Port

ASMi-450 Preparations

Supervision Terminal

Connections

4.3 Preparation for Use of Supervision Terminal

Internal Settings

See Section 2-4 for detailed information.

In general you must enter a password when you start a control session. If the password is incorrect, the ASMi-450 will not respond. This can be corrected by appropriate setting of the PSWD section of switch S1. Set the PSWD section of switch S1 as follows:

OFF	In this position, you can define your own password and node
	address.
ON	Set the switch section to ON to restore the default ASMi-450
	password (ASMI), and change the node address to the default
	value of 0. The change will be made after you turn the
	ASMi-450 off for a short time, and then turn it back on.

Control Port Configuration

Configure the ASMi-450 control port as required. See Sections 3-5 through 3-7.

If the control port parameters are not correct, the ASMi-450 will not respond. This can be corrected by appropriate setting of the DEF SP section of switch S1. Set the DEF SP section of switch S1 as follows:

OFF	In this position, you can define the desired control port
	parameters.
ON	Set the switch section to ON to restore the default control port
	parameters. The change will be made after you turn the
	ASMi-450 off for a short time, and then turn it back on.

Configure the terminal for the same communication parameters you selected for the ASMi-450 control port.

Connect the control cable (coming directly from the terminal, or from the modem used to connect the terminal) to the CONTROL DCE connector of the ASMi-450. See Appendix A for cable wiring information.

Turn the control terminal on and when applicable, turn on the modems and the other communication equipment used to connect the terminal to the ASMi-450.

ASMi-450 Installation and Operation Manual

4-5

Image 63

Contents ASMi-450 Warranty Hdsl SelvRegulatory Information Declaration of Conformity Page Contents ASMi-450 Control from the Control Port Appendix a Connector Wiring Contents List of Figures List of Figures Xii List of Tables List of Tables Xiv Preliminary Preparations Starting Procedure Starting the ConfigurationConfiguration Procedure Step Action Use the CommandFunction Terminal Type TV920 VT52 VT100 Freedom 100/110 Type Configuration Display Commands Control Commands Command IndexQuick-Start Guide Functional Description Purpose and Main FeaturesTypical Application for ASMi-450 with Data Interface Hdsl Subsystem Characteristics Internal timing System TimingControl ASMi-450 Operation Local ControlRemote Management Introduction Power Requirements Test and Diagnostics CapabilitiesAlarms Physical CharacteristicsTransmission Media Hdsl Line Signal Binary Digits Quaternary SymbolOperating Environment Hdsl Signal Structure HDSL-Related System Functions Hdsl Interface Technical SpecificationsEthernet Interface Physical Characteristics General Chapter InstallationSite Requirements UnpackingASMi-450 Configuration Information GeneralOpening ASMi-450 Case Switch S1 Jumper and Switch Location FunctionsASMi-450 Internal Settings OFF Internal Settings Procedure Reinstalling ASMi-450 Cover Jumper R/CJumper FGND/GND Connector Location Grounding Power Connection Users Port Connections AC Power ConnectionDC Power Connection Hdsl Line Connections Control Port Connection Scope Chapter Front-Panel Operating InstructionsControl or Indicator Function Front Panel Controls, Connectors, and IndicatorsIndicators Indicator FunctionEthernet Interface General General Operating Instructions Display Functions Control of ASMi-450 Operation, GeneralDisplay Description See Configuration ParametersStatus Messages Test FunctionsPush-buttons Using Front-PanelOrganization ASMi-450 DisplayFront-Panel Operating Instructions Designation Function Values System Configuration ParametersControl Port Configuration Parameters Operating Instructions Turn-on Checking Current Operating ConfigurationDisplay CursorScroll Ethernet Interface Indications Fault IndicationsStep Action Key Display Normal Front-Panel IndicationsProtection Local Configuration Set-Up ProcedurePassword Configuration ProcedureAlready there Scroll to display the desired group Alarm Buffer Specific Configuration GuidelinesSP Parameters LCD Configuration Error Messages Front-Panel Operating Instructions Chapter ASMi-450 Control from the Control Port Hardware Requirements Clear to Send CTS Interface TypeData Terminal Ready DTR Request to Send RTSAutobaud Function Ring Indication RIData Set Ready DSR ASMi-450 Preparations Supervision Terminal Connections Internal SettingsControl Port Configuration Preparation for Use of Supervision TerminalOption Meaning Example of Usage Command Language Syntax Command OptionsCommand Protocol ASMi-450 Supervision LanguageIndex of Commands Command Purpose Options Format ASMi-450 Command Set DescriptionCLR ALM CLR LoopCLR TST DateDEF Agent Display Fields DEF NameDEF PWD DEF NodePurpose Format Use DEF SPPWD DEF Term DEF SYSDSP ALM Function Terminal Type VT-52 VT-100 Freedom-110Format Use Alarm No Alarm Syntax Meaning State Time Remote DB Remote AlarmRemote Signal Loss Quality AlarmConnected DSP HDR TSTDSP ST Line REM LAN notDSP ST Port Display FormatPurpose Format Use Display Format Exit DSP ST SYSHelp Init DB Parameter Designation Default ValuePassword LoopNode Time ResetStarting a Session Single ASMi-450 Control Session Ending a Control Session Configuration Error Messages ASMi-450 Control from the Control Port Status Indications and Messages Indicators DisplayON/OFF Message Description Corrective Actions AlarmASMi-450 Alarm Buffer Messages Cont’d Remote Alarm Remote Reverse Test Functions Test FunctionsOperating Instructions Loop REM REM PortActivating the Test Functions from a Control Terminal Power-Up Self-TestTrouble Symptoms Probable Cause Corrective Measures Troubleshooting InstructionsLAN Pin Designation Direction Function RS-530 DCE Connector and Adapter CablesPin Designation Direction Function 36/RS-449/422 RceaRceb V.35 DCE Connector X.21 DCE Connector Pin Line Connected Connected to To Terminal Hdsl Line ConnectorRS-232 V.24 Control Port Connector Pin FunctionEthernet Interface Connector Appendix B Snmp Management Snmp Environment General Snmp PrinciplesSnmp Operations Management Information Base MIB StructureMIBs Supported by the ASMi-450 Snmp Agent Access Restriction Using Snmp Communities Management Domains UnderSnmp Communities Read ASMi-450 CommunitiesAddress Class First Byte Address Range IP EnvironmentGeneral IP Environment IP Address StructureSnmp Management Snmp Traps Appendix C Installation in 19 Racks Figure C-1. Installation of Single Unit in 19 Rack Installation of Single UnitGeneral Preparations Installation of Two UnitsFastening the Two Units ASMi-450 To install the ferrite cores