Rockford Fosgate T1500-1bd Troubleshooting, Procedure 1 Check Amplifier for proper connections

Page 9

TROUBLESHOOTING

NOTE:If you are having problems after installation follow the Troubleshooting procedures below.

Procedure 1: Check Amplifier for proper connections.

Verify that POWER light is on. If POWER light is on skip to Step 3, if not continue.

1. Check in-line fuse on battery positive cable. Replace if necessary.

2. Check fuse(s) on amplifier. Replace if necessary.

3. Verify that Ground connection is connected to clean metal on the vehicle’s chassis. Repair/replace if necessary.

4. Verify there is 9 to 16 Volts present at the positive battery and remote turn-on cable.Verify quality connections for both cables at amplifier, stereo, and battery/fuseholder. Repair/replace if necessary.

Procedure 2: Protect or Thermal light is on.

1. If the Protect light is on, this is a sign of a possible short in the speaker connections. Check for proper speaker connections and use an ohm meter to check for possible shorts in the speaker wiring. Too low of a speaker impedance may also cause Protect to light.

2. If the Thermal light is on, check for proper speaker impedance, rewire if needed.This can also be a sign of driving the amplifier at very high power levels without adequate airflow around the amplifier. Shut off the system and allow amplifier to cool. Check that the vehicle charging system is maintaining proper voltage. If the previous items do not solve the problem, a fault may be in the amplifier, call customer service for support.

Procedure 3: Check Amplifier for audio output.

1. Verify good RCA input connections at stereo and amplifier. Check entire length of cables for kinks, splices, etc.Test RCA inputs for AC volts with stereo on. Repair/replace if necessary.

2. Disconnect RCA input from amplifier. Connect RCA input from test stereo directly to amplifier input.

Procedure 4: Check Amplifier if you experience Turn-on Pop.

1. Disconnect input signal to amplifier and turn amplifier on and off.

2. If the noise is eliminated, connect the REMOTE lead of amplifier to source unit with a delay turn-on module.

OR

1. Use a different 12 Volt source for REMOTE lead of amplifier (i.e. battery direct).

2. If the noise is eliminated, use a relay to isolate the amplifier from noisy turn-on output.

Procedure 5: Check Amplifier if you experience excess Engine Noise.

1. Route all signal carrying wires (RCA, Speaker cables) away from power and ground wires.

OR

2. Bypass any and all electrical components between the stereo and the amplifier(s). Connect stereo directly to input of amplifier. If noise goes away the unit being bypassed is the cause of the noise.

OR

3. Remove existing ground wires for all electrical components. Reground wires to different locations. Verify that grounding location is clean, shiny metal free of paint, rust etc.

OR

4. Add secondary ground cable from negative battery terminal to the chassis metal or engine block of vehicle.

OR

5. Have alternator and battery load tested by your mechanic.Verify good working order of vehicle electrical system including distributor, spark plugs, spark plug wires, voltage regulator etc.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Installation Operation Introduction Table of ContentsContents of Carton Safety InstructionsVariable Cr Design FeaturesMounting Locations InstallationEngine Compartment Trunk MountingWiring the System Battery and ChargingCurrent and could induce noise into the audio system Passenger Compartment MountingPower Connection Adjusting Gain Adjusting Crossover FrequencyOperation Infrasonic FilterProcedure 1 Check Amplifier for proper connections TroubleshootingProcedure 2 Protect or Thermal light is on Procedure 3 Check Amplifier for audio outputSpecifications MODEL- PowerSpecifications subject to change without notice Limited Warranty Information Length of WarrantyTable DES Matières InstallatNuméro de modèle Fonctionne entConsignes DE Sécurité Un amplificateur mono Power, modèleMise EN Garde Contenu DE LemballageParticularités Techniques CommandeEmplacements DE Montage Installation Considérations Concernant L’INSTALLATIONConfiez la tâche à un technicien qualifié De dommages à lappareilBatterie ET Charge Votre distributeur agréé Rockford FosgateMontage dans l’habitacle Causer des blessures ou endommager lampli et/ou les Composants qui lui sont connectésConnexion Dalimentation Filtre Infrasonique FuncionamientoÉgaliseur Punch Réglage DE LA Fréquence DU Filtre PassifDépannage Procédure 2 Le voyant de protection ou thermique est alluméProcédure 3 Vérifiez la sortie audio de lampli Modèle Power CaractéristiquesLes spécifications sont sujettes à changements sans préavis Informations SUR LA Garantie Limitée Durée de la garantieÍndice DE Materias IntroducciónNúmero de la serie Número del modelo NOTALea cada sección para obtener información más detalladaInstrucciones DE Seguridad PrecauciónContenido DE LA Caja LED Características DEL DiseñoLugares DE Montaje Instalación Consideraciones Para LA InstalaciónDestornillador Phillips No Compartimento del motorBateríay Carga InstalaciónCableado DEL Sistema Instalación en la cabina de pasajerosConexión de Corriente Daños al amplificador o a los componentes conectadosNOTALas salidas están conectadas en paralelo internamente Filtro Infrasónico Remote Punch EQ OpcionalAjuste DE LA Frecuencia X-OVER Transición Ajuste DE GananciaEstá encendida vaya al Paso 3,de otra manera,continúe Solución DE ProblemasEspecificaciones Modelo PowerInformación Sobre LA Garantía Limitada Duración de la garantíaInhaltsverzeichnis EinleitungSeriennummer Modellnummer Einleitung Sicherheitshinweise DesigncharakteristikenDieses Symbol mit dem Wort „VORSICHT soll den Benutzer auf Dieses Symbol mit dem Wort „WARNUNG soll den Benutzer aufSicherheitshinweise Führt zu schweren Verletzungen oder TodHinweis DesigncharakteristikenBefestigungsstellen Einbau EinbauüberlegungenMotorraum Einbau im KofferraumBatterie UND Aufladung EinbauVerkabelung DES Systems Einbau im InnenraumKomponenten verursacht werden StromanschlüssePlötzliches Anhalten aus den Panelen lösen PUNCH-EQ-FERNBEDIENUNG wahlweise BetriebInfraschallfilter CROSSOVER-FREQUENZ EinstellenVerfahren 2Schutz- oderThermallicht leuchtet auf FehlerbeseitigungVerfahren 3DenVerstärker aufAudioleistung überprüfen OderTechnische Daten MODELL- Power T500-1bd T1000-1bdT1500-1bd Die technischen Daten können sich ohne Ankündigung ändernInformationen ZUR Beschränkten Garantie Laufzeit der GarantieIndice IntroduzioneNumero di serie Numero di modello RagguagliContenuto DELL’IMBALLAGGIO Istruzioni DI SicurezzaCaratteristiche DEL Design Posizionamento Installazione Considerazioni SULL’INSTALLAZIONEScompartimento del motore Montaggio nel bagagliaioBatteria E Caricamento InstallazioneCablaggio DEL Sistema Montaggio nello scampartimento passeggeriNOTALe uscite sono collegate parallelamente allinterno Collegamento Alla tensioneFiltro Infrasonico FunzionamentoEqualizzatore EQ Regolazione Della Frequenza DI IncrocioOppure INDIVIDUAZIONE/RIPARAZIONE GuastiAltrimenti continuare Procedura 3Controllare le uscite audio dell’amplificatoreModello Power SpecificheSpecifiche soggette a modiche senza preavviso Informazioni Inerenti Alla Garanzia Limitata Lunghezza della garanzia07/08 B.M 1230-55271-01
Top Page Image Contents