MGE UPS Systems EX-5, EX-7, EX-11RT manual CLA Module Contents, EX 5/7/11RT, Recommended Batteries

Page 26

EX 5/7/11RT Systems

1.5.8CLA Charger Module

Extended back-up time (up to 8 hours at full load) requires a high power battery cabinet connected to the EX 5/7/11RT via the CLA Module.

IMPORTANT

The CLA can not be used to charge the Battery Module (EXB). It is designed to

charge the customer provided high power battery cabinet.

Figure 1-12: CLA Module Contents and Connections.

CLA Module Contents

Tower Stand Expanders

Transformer Rail Kit

 

 

CLA Module Quick Start

 

 

Battery Power Cable

41

 

 

 

 

Stabilizer Bracket

 

 

(4 screws included)

 

Battery Detection Cable

 

CLA

Typical High Power Battery Cabinet

15A Utility

AC Source

(cable not included)

(not included)

EX 5/7/11RT

~

(see section 2.10 for cable connection information)

(cable not included)

Table 1-7: Battery backup time chart.

Total battery voltage : 240 VDC (20 x 12VDC, one string).

Battery Backup Time

 

 

 

Recommended Batteries

 

 

 

 

 

 

 

 

 

 

 

 

EX 5RT

 

EX 7RT

 

EX 11RT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2 hours

 

 

50 Ah

 

65 Ah

 

100 Ah

 

 

 

 

 

 

 

 

 

 

4 hours

 

 

100 Ah

 

130 Ah

 

200 Ah

 

 

 

 

 

 

 

 

 

 

8 hours

 

 

200 Ah

 

260 Ah

 

400 Ah

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IMPORTANT

The battery capacity must be set within the UPS (5 Ah increment)

 

See UPS Personalization section 3.2.

1 — 12

Introduction

86-86000-00 B00

Image 26
Contents EX 5/7/11RT Systems Page MGE UPS SYSTEMS, INC Scenic Avenue Costa Mesa, CA 92626 714 Technical Support Customer Care Center Hours 24/7EX 5/7/11RT Systems Contents Setup and Installation Technical Support and Product Services Return Policy for Repair of Single Phase Products RGAFigures Tables Important Safety Instructions Certification StandardsSpecial Precautions EnvironmentAdditional Modules Serial Numbers Section Descriptions This page left blank intentionally Scope Input voltage must be the same as output voltage on HV unitsPart Number Description System Electrical Characteristics Transformer Module Characteristics RatingsStandard Configuration Tower ConfigurationModel Dimensions HxWxD Weights Rack ConfigurationPower Module EX 5/7/11 RT Rear Panel Components1 1 R T Power Module Display and Control PanelEX RT Transformer Module Battery/Transformer/CLA Module Rail Kit Optional AccessoriesPower Module Rail Kit Multiple Battery Module Backup Time at Full Load Battery Extension Cable KitBattery Integration Kit with Casters Input/Output BoxEX RT Transformer Module Contents Recommended Batteries CLA Module ContentsEX 5/7/11RT Unpacking and Parts Check All Modules are shipped in separate boxesContents of Standard EX 5/7/11RT Systems Contents of EXB 5/7/11RT Battery Module PN 86207 /86209 Installation in Tower Configuration Installation in Rack Mounting Configuration Not to scale Page Install input/output cables Per .7 prior to this step Bracket SystemConnecting the RS232 Communication Port Communication PortsConnecting the Dry Relay Contact Communication Port Installation of Optional Transverse CardProper operation Dual U-Talk/Basic CardJBus Card Dual port Shut CardRemote Emergency Power Off Repo Communication Port Sources are open OFF/OPEN System ConnectionsMax AWG EX 11RT Always connect the earth ground wire first Output120VAC output terminals Lb-N, La-N Connecting EX RT Transformer ModuleProtection for all transformer output terminals Bypass AC Mains Power Module I/O Box Connection of Battery Module EXB AC Input Connection of Optional CLA ModuleThis page left blank intentionally Initial Startup Required for initial startup onlyUPS Personalization Control Panel with scroll up and down buttonsDisplay Factory setting Options Display Factory setting Options CommentsMGE UPS SYSTEMS, INC Symptoms IT Network mode Industrial mode Final Startup sequence Then go to Advanced settings and UPS settingsUPS personalization through external software During the startup, if the Bypass AC source is outNormal double conversion Mode Operating ModesECO Mode ECO mode displayFirst Case Operation on battery Operation on Battery PowerTransfer to Battery Power Second Case Low battery warningShutdown Power to the loadReturn of Normal AC source Troubleshooting Symptoms Indication CorrectionBattery Fault LED Hot Swapping the Power Module 1CXXXXXXXRe-connecting the Power Module Re-connecting the Battery Module Hot Swapping the Battery ModuleDisconnecting the Battery Module This page left blank intentionally System Overload Characteristics Electrical SpecificationsSystem Input/Output Power Ratings Source Voltage FrequencyEX RT CLA Module System Backup CharacteristicsSystem Short Circuit Protection Configuration for Hours backup time KVA / kW 25% 50% 75% 100% Output load percentageHeat Rejection Environmental CharacteristicsOperation Mode On-line On Battery SystemMGE Standard Single Phrase Warranty Proprietary Rights StatementProduct information Warranty Extension Warranty+ not available on productsUser Information Scheduling Field Service Engineer Support Part Number Assembly Number Serial numberEX 5/7/11RT Systems Glossary IEC Osha This page left blank intentionally Reorder Form Scenic Avenue Costa Mesa, CA Contact MGE