MGE UPS Systems EX-5, EX-7, EX-11RT manual Figures

EX 5/7/11RT Systems

Figures

figure	description	. .page
1-1:	Tower Configuration with Power Module, Battery Module,
	and optional Transformer Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 4
1-2:	Rack Configuration with Power Module, Battery Module,
	and optional Transformer Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 5
1-3:	Rear panel of the Power Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 — 6
1-4:	Rear Panel of the Battery Module	.1 — 6
1-5:	Rear Panel of the optional Transformer Module. (PN 86211)	.1 — 7
1-6:	View of typical control panel interface	.1 — 7
1-7:	Power Module Rail Kit	.1 — 8
1-8:	Battery/Transformer/CLA Module Rail Kit. . . . . . . . . . . . . . . . . . . . . . . . .1 — 8
1-9:	Typical back-up time with multiple EXB’s at full load. . . . . . . . . . . . . . . .1 — 9
1-10:	Typical Battery Integration kit with casters setup. . . . . . . . . . . . . . . . . .1 — 10
1-11:	Typical Transformer Module contents and connections. . . . . . . . . . . . .1 — 11
1-12:	CLA Module Contents and Connections	1 — 12
2-1:	Contents of EX 5/7/11RT Power Module. . . . . . . . . . . . . . . . . . . . . . . . .2 — 2
2-2:	Contents of EXB 5/7/11RT Battery Module	.2 — 3
2-3:	Tower Configuration of Standard System and
	Optional Transformer Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 5
2-4:	Typical orientation of the logo and control panel.
	(Power Module shown)	.2 — 6
2-5:	Accessing Battery Pack	.2 — 6
2-6:	Rack mounting of the Power Module onto the rails. . . . . . . . . . . . . . . . .2 — 7
2-7:	Input/Output Box Bracket System	.2 — 8
2-8:	RS232 Communication Cable Connection. . . . . . . . . . . . . . . . . . . . . . . .2 — 9
2-9:	Relay Pin Connections for Communication Port	2 — 10
2-10:	Communication Card Slot with Network
	Management Card installed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 10
2-10a: Activation of Remote Emergency Power Off function
	using a contact normally open switch	2 — 12
2-10b: Activation of Remote Emergency Power Off using a
	contact normally closed switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 12
2-11:	Power Module I/O Box Terminal Block Diagram	2 — 13
2-12:	Normal AC Input and Output Cables installation	2 — 14
2-13:	View of EX RT Transformer Module connected downstream
	for 120/208/240 Vac outputs (shown with one EXB)	2 — 15
2-14:	Normal AC Input, Bypass AC, and Output Cables Installation,
	and Simplified Connection Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . .2 — 16
2-15:	Accessing Terminal Blocks for Input and Output power cables. . . . . . .2 — 17
2-16:	Rear view of Battery Module cable connections	2 — 18
2-17:	Rear view of CLA Module cable battery and AC input connections . . . .	2 — 19

c iv Contents 86-86000-00 B00