MGE UPS Systems EX-5, EX-7, EX-11RT manual Osha

Page 73

Installation and User Manual

OSHA

Occupational Safety and Health Agency.

PCA

Printed circuit assembly.

PCB

Printed circuit board.

PN

Part number.

PWM

Pulse Width Modulation.

RCD Load

Load consists of resistor, capacitor and diode. A computer with switched

 

mode power supply is considered a RCD load.

RL Load

Load consists of resistor, and inductor. A fan or a drill is considered a RL

 

load.

SCR

Silicon controlled rectifier.

Shipping damage

Any damage done to an article while it is in transit.

SPDT

Single Pole Double Throw.

Static Transfer

An solid state switching mechanism electronically controlled to pass AC power

 

directly from the utility to an output load.

Technician

Refers to an electronic technician qualified to maintain and repair electronic

 

equipment. Not necessarily qualified to install electrical wiring.

V

Volts

VA

Volt amperes

VA

Volt-amps, unit for apparent power measurement, equal V x I.

VAC or Vac

Voltage of AC type.

VDC or Vdc

Voltage of DC type.

ve

Battery voltage.

Via

By way of.

86-86000-00 B00

Glossary

G — 3

Image 73
Contents EX 5/7/11RT Systems Page Technical Support Customer Care Center Hours 24/7 MGE UPS SYSTEMS, INC Scenic Avenue Costa Mesa, CA 92626 714EX 5/7/11RT Systems Contents Setup and Installation Return Policy for Repair of Single Phase Products RGA Technical Support and Product ServicesFigures Tables Certification Standards Important Safety InstructionsEnvironment Special PrecautionsAdditional Modules Serial Numbers Section Descriptions This page left blank intentionally Input voltage must be the same as output voltage on HV units ScopePart Number Description Transformer Module Characteristics Ratings System Electrical CharacteristicsTower Configuration Standard ConfigurationRack Configuration Model Dimensions HxWxD WeightsRear Panel Components Power Module EX 5/7/11 RTEX RT Transformer Module Power Module Display and Control Panel1 1 R T Power Module Rail Kit Optional AccessoriesBattery/Transformer/CLA Module Rail Kit Battery Extension Cable Kit Multiple Battery Module Backup Time at Full LoadInput/Output Box Battery Integration Kit with CastersEX RT Transformer Module Contents EX 5/7/11RT CLA Module ContentsRecommended Batteries All Modules are shipped in separate boxes Unpacking and Parts CheckContents of Standard EX 5/7/11RT Systems Contents of EXB 5/7/11RT Battery Module PN 86207 /86209 Installation in Tower Configuration Installation in Rack Mounting Configuration Not to scale Page Bracket System Install input/output cables Per .7 prior to this stepCommunication Ports Connecting the RS232 Communication PortInstallation of Optional Transverse Card Connecting the Dry Relay Contact Communication PortJBus Card Dual U-Talk/Basic CardProper operation Dual port Shut CardRemote Emergency Power Off Repo Communication Port Max AWG EX 11RT System ConnectionsSources are open OFF/OPEN Output Always connect the earth ground wire firstProtection for all transformer output terminals Connecting EX RT Transformer Module120VAC output terminals Lb-N, La-N Bypass AC Mains Power Module I/O Box Connection of Battery Module EXB Connection of Optional CLA Module AC InputThis page left blank intentionally Required for initial startup only Initial StartupControl Panel with scroll up and down buttons UPS PersonalizationDisplay Factory setting Options Comments Display Factory setting OptionsMGE UPS SYSTEMS, INC Symptoms IT Network mode Industrial mode UPS personalization through external software Then go to Advanced settings and UPS settingsFinal Startup sequence During the startup, if the Bypass AC source is outOperating Modes Normal double conversion ModeECO mode display ECO ModeTransfer to Battery Power Operation on Battery PowerFirst Case Operation on battery Second Case Low battery warningReturn of Normal AC source Power to the loadShutdown Symptoms Indication Correction TroubleshootingBattery Fault LED 1CXXXXXXX Hot Swapping the Power ModuleRe-connecting the Power Module Disconnecting the Battery Module Hot Swapping the Battery ModuleRe-connecting the Battery Module This page left blank intentionally System Input/Output Power Ratings Electrical SpecificationsSystem Overload Characteristics Source Voltage FrequencySystem Short Circuit Protection System Backup CharacteristicsEX RT CLA Module KVA / kW 25% 50% 75% 100% Output load percentage Configuration for Hours backup timeOperation Mode On-line On Battery Environmental CharacteristicsHeat Rejection SystemProprietary Rights Statement MGE Standard Single Phrase WarrantyUser Information Warranty Extension Warranty+ not available on productsProduct information Part Number Assembly Number Serial number Scheduling Field Service Engineer SupportEX 5/7/11RT Systems Glossary IEC Osha This page left blank intentionally Reorder Form Scenic Avenue Costa Mesa, CA Contact MGE