Runco manual Connectors, SP-42, SP-50 and SP-60 respectively

Page 17

Controls and Functions

Figure 2-2, Figure 2-3and Figure 2-4show the rear-panel connector locations on the	Connectors
SP-42, SP-50 and SP-60 respectively.

14

15

16

17

RS-232DVI VIDEO

COMPONENT

9

10

11

12

13

IN OUT

COMBINATION

RS-232C

OUTPUT INPUT1 INPUT2

AUDIO AUDIO AUDIO


		INPUT1			INPUT2
ANALOG RGB OUT	ANALOG RGB IN			DIGITAL RGB
(D-Sub)		(D-Sub)		(DVI-D)

1

2

3

4

5

6

7

8

Figure 2-2. SP-42 Connector Panel

Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual

7

Image 17

Contents SP-42 SP-50 SP-60 Page For Plasma Displays Three Year Limited WarrantyRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions Table of Contents Specifications Maintenance and TroubleshootingOperation Serial CommunicationsList of Figures Page About This Manual IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories CinemaWall at a Glance Controls and IndicatorsControls and Functions Display Stand SP-42, SP-50 and SP-60 respectively ConnectorsSP-50 Connector Panel Combination IN/OUT Main Power Switch CinemaWall Remote ControlSET Button Page Remote Control InstallationOther surfaces Step Procedure For Details, refer to Quick SetupConsiderations InstallationHigh-Altitude Operation Mounting the CinemaWallVentilation Ambient LightInstallation Video Connections Connections to the CinemaWallAnalog RGB OUT Input 1 Connection Standby modeComposite or S-Video Input 3 Connection Computer/Video Signal Compatibility onComponent Video Input 4 Connection Attaching the Small Ferrite Cores to Audio Cables Audio Connections11. Audio Output Connection Connection RS-232 ControllerPage Changing the OSD Language Turning on the PowerOperation Setting the Computer Display Properties Selecting an Input Source Viewing Input Signal InformationChanging the Aspect Ratio Aspect Ratio Description Aspect Ratio SettingsPIX by PIX Trained service personnel only Using the On-Screen MenusInstaller Adjust menu is intended for use by authorized CinemaWall OSD Menu Structure Picture Main MenuTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Screen OFF PowerSet-Up DVI Setup Option Language Refer to Changing the OSD Language onUnder some conditions such as when the input signal consists Installer ADJ Input Option Installer Adjust ModeFAN Speed Auto ISF CCC color mode is pre-set to approximately 3,200K This action is not undoable. Proceed with caution Seamless Switch is not available when using PIPTo use PIP, press the Split button Using Picture-In-Picture PIPPIP Windows Swapping the MainViewing an Enlarged Area of the Display Enlarging One Part of the ScreenPage Cleaning Maintenance and TroubleshootingTroubleshooting Tips Cleaning the Display Panel Body and Remote ControlThermal Alert OUT of Range Signal NGShut Down FAN FailureSerial Command Syntax RS-232 Connection and Port ConfigurationSerial Communications ExampleMinimum Maximum Command Value Range DescriptionInput Select Note Aspect RatioPicture-in-Picture PIP VideoAudio MSTS10 MSTS08MSTS09 Sets 2-screen operation to 2 Screen SET-UP Menu CommandsSide-by-side, full height main screen On leftHigh LOWAuto Option Menu CommandsAverage Picture Menu Commands Installer Adjust Mode Option Menu Commands Installer Adjust Mode Screen Menu Commands Installer Adjust ModeSET-UP Menu Commands Installer Adjust Mode FMKS02 FMKS00FMKS03 FMKS044F 53 44 53 30 Sets OSD Display to OFF DW1 Minimum Maximum Adjustment CommandsDWF UPFCinemaWall Specifications SpecificationsDate of delivery to the end user Specifications are subject to change without noticeCinemaWall DimensionsCinemaWall Model SP-50 Dimensions with Optional Table Stand CinemaWall Model SP-60 Dimensions with Optional Table Stand Input Refresh Rate Resolution Computer/Video Signal CompatibilityRemarks Horiz56.0 45.1 Page Page Runco CL-810 Owner’s Operating Manual