Runco SP-50, SP-42, SP-60 manual Picture Menu Commands Installer Adjust Mode

Page 70

Serial Communications

Table 6-1. Serial Commands (continued)

	Command				Value Range		Description
							Description
ASCII				HEX	Minimum	Maximum

TPM		54 50		4D	000	059	Sets the minute of the present time.

TPTS00		54 50 54 53 30 30			–	–	Deactivates program timer.

TPTS01		54 50 54 53 30 31			–	–	Activates program timer.

TPW		54 50 57			001	007	Sets the day of the week of the present
							time (001 = Sunday ... 007 = Saturday).

TSMS00		54 53		4D 53 30 30	–	–	Sets Daylight Saving Time to OFF.

TSMS01		54 53		4D 53 30 31	–	–	Sets Daylight Saving Time to ON.

				PICTURE Menu Commands (Installer Adjust Mode)

BHI		42 48 49			000	255	Adjusts blue gain (highlight).

BLW		42 4C 57			000	255	Adjusts blue offset (lowlight).

BRT		42 52 54			000	255	Adjusts brightness.

CGB		43 47 42			000	060	Adjusts BLUE color detail.

CGC		43 47 43			000	060	Adjusts CYAN color detail.

CGG		43 47 47			000	060	Adjusts GREEN color detail.

CGM		43 47		4D	000	060	Adjusts MAGENTA color detail.

CGR		43 47 52			000	060	Adjusts RED color detail.

CGY		43 47 59			000	060	Adjusts YELLOW color detail.

CNT		43	4E 54		000	255	Adjusts contrast.

COL		43	4F	4C	000	127	Adjusts color intensity.

ENH		45	4E 48		000	015	Adjusts H. SHARPEN.

ENV		45	4E 56		000	015	Adjusts V. SHARPEN.

GHI		47 48 49			000	255	Adjusts green gain (highlight).

GLW		47 4C 57			000	255	Adjusts green offset (lowlight).

GRAS18		47 52 41 53 31 38			–	–	Sets the GAMMA to 1.8.

GRAS19		47 52 41 53 31 39			–	–	Sets the GAMMA to 1.9.

GRAS20		47 52 41 53 32 30			–	–	Sets the GAMMA to 2.0.

GRAS21		47 52 41 53 32 31			–	–	Sets the GAMMA to 2.1.

GRAS22		47 52 41 53 32 32			–	–	Sets the GAMMA to 2.2.

GRAS23		47 52 41 53 32 33			–	–	Sets the GAMMA to 2.3.

Notes:

1.When making input-specific adjustments such as to image quality, screen position/size or audio sub-volume, select the input you wish to affect before making such adjustments.

2.These settings are not stored in memory.

60 Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual

Image 70

Contents SP-42 SP-50 SP-60 Page Three Year Limited Warranty For Plasma DisplaysRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation Maintenance and TroubleshootingSpecifications Serial CommunicationsList of Figures Page Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Functions Controls and IndicatorsCinemaWall at a Glance Display Stand Connectors SP-42, SP-50 and SP-60 respectivelySP-50 Connector Panel Combination IN/OUT CinemaWall Remote Control Main Power SwitchSET Button Page Installation Remote ControlOther surfaces Quick Setup Step Procedure For Details, refer toHigh-Altitude Operation InstallationConsiderations Mounting the CinemaWallAmbient Light VentilationInstallation Connections to the CinemaWall Video ConnectionsStandby mode Analog RGB OUT Input 1 ConnectionComputer/Video Signal Compatibility on Composite or S-Video Input 3 ConnectionComponent Video Input 4 Connection Audio Connections Attaching the Small Ferrite Cores to Audio Cables11. Audio Output Connection RS-232 Controller ConnectionPage Operation Turning on the PowerChanging the OSD Language Selecting an Input Source Viewing Input Signal Information Setting the Computer Display PropertiesChanging the Aspect Ratio Aspect Ratio Settings Aspect Ratio DescriptionPIX by PIX Installer Adjust menu is intended for use by authorized Using the On-Screen MenusTrained service personnel only CinemaWall OSD Menu Structure Main Menu PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Screen Set-Up PowerOFF DVI Setup Language Refer to Changing the OSD Language on OptionUnder some conditions such as when the input signal consists Option Installer Adjust Mode Installer ADJ InputFAN Speed Auto ISF CCC color mode is pre-set to approximately 3,200K Seamless Switch is not available when using PIP This action is not undoable. Proceed with cautionUsing Picture-In-Picture PIP To use PIP, press the Split buttonSwapping the Main PIP WindowsEnlarging One Part of the Screen Viewing an Enlarged Area of the DisplayPage Troubleshooting Tips Maintenance and TroubleshootingCleaning Cleaning the Display Panel Body and Remote ControlShut Down OUT of Range Signal NGThermal Alert FAN FailureSerial Communications RS-232 Connection and Port ConfigurationSerial Command Syntax ExampleInput Select Note Command Value Range DescriptionMinimum Maximum Aspect RatioAudio VideoPicture-in-Picture PIP MSTS09 MSTS08MSTS10 Side-by-side, full height main screen SET-UP Menu CommandsSets 2-screen operation to 2 Screen On leftLOW HighAverage Option Menu CommandsAuto Picture Menu Commands Installer Adjust Mode SET-UP Menu Commands Installer Adjust Mode Screen Menu Commands Installer Adjust ModeOption Menu Commands Installer Adjust Mode FMKS03 FMKS00FMKS02 FMKS044F 53 44 53 30 Sets OSD Display to OFF DWF Minimum Maximum Adjustment CommandsDW1 UPFSpecifications CinemaWall SpecificationsSpecifications are subject to change without notice Date of delivery to the end userDimensions CinemaWallCinemaWall Model SP-50 Dimensions with Optional Table Stand CinemaWall Model SP-60 Dimensions with Optional Table Stand Remarks Computer/Video Signal CompatibilityInput Refresh Rate Resolution Horiz56.0 45.1 Page Page Runco CL-810 Owner’s Operating Manual