Runco SP-60, SP-42, SP-50 manual Selecting an Input Source Viewing Input Signal Information

Page 38

Operation

4.3

Selecting an Input Source

4.4

Viewing Input Signal Information

To select an input source, press a numbered button on the remote control corresponding to that input.

Press INFO on the remote control to have the CinemaWall display the currently-selected input, signal timing information (frequency and polarity) and aspect ratio. This information stays on-screen for about five seconds.

RGB-HD DVI-D INFO

1 2

S / V

COMP

DVI VIDEO

3 4 5

INPUT SELECTION

INPUT1

FH : 31 . 5 k Hz

FV : 60 . 0Hz

640 X 480

POL.H : NEGA

POL.V : POSI

PIX BY PIX

4.5

Setting the Computer Display Properties

To maximize image quality when using the CinemaWall with a personal computer, you may need to adjust the display properties of your computer’s video card. To do this on a Microsoft® Windows®-based PC:

1.Choose Settings from the Windows Start Menu and click on “Control Panel.”

2.Double click on the Display icon.

3.Click the Settings tab on the display dialog box.

4.Adjust the resolution to 1024x768 pixels.

28 Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual

Image 38

Contents SP-42 SP-50 SP-60 Page Three Year Limited Warranty For Plasma DisplaysRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation Maintenance and TroubleshootingSpecifications Serial CommunicationsList of Figures Page Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories CinemaWall at a Glance Controls and IndicatorsControls and Functions Display Stand Connectors SP-42, SP-50 and SP-60 respectivelySP-50 Connector Panel Combination IN/OUT CinemaWall Remote Control Main Power SwitchSET Button Page Installation Remote ControlOther surfaces Quick Setup Step Procedure For Details, refer toHigh-Altitude Operation InstallationConsiderations Mounting the CinemaWallAmbient Light VentilationInstallation Connections to the CinemaWall Video ConnectionsStandby mode Analog RGB OUT Input 1 ConnectionComputer/Video Signal Compatibility on Composite or S-Video Input 3 ConnectionComponent Video Input 4 Connection Audio Connections Attaching the Small Ferrite Cores to Audio Cables11. Audio Output Connection RS-232 Controller ConnectionPage Changing the OSD Language Turning on the PowerOperation Selecting an Input Source Viewing Input Signal Information Setting the Computer Display PropertiesChanging the Aspect Ratio Aspect Ratio Settings Aspect Ratio DescriptionPIX by PIX Trained service personnel only Using the On-Screen MenusInstaller Adjust menu is intended for use by authorized CinemaWall OSD Menu Structure Main Menu PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Screen OFF PowerSet-Up DVI Setup Language Refer to Changing the OSD Language on OptionUnder some conditions such as when the input signal consists Option Installer Adjust Mode Installer ADJ InputFAN Speed Auto ISF CCC color mode is pre-set to approximately 3,200K Seamless Switch is not available when using PIP This action is not undoable. Proceed with cautionUsing Picture-In-Picture PIP To use PIP, press the Split buttonSwapping the Main PIP WindowsEnlarging One Part of the Screen Viewing an Enlarged Area of the DisplayPage Troubleshooting Tips Maintenance and TroubleshootingCleaning Cleaning the Display Panel Body and Remote ControlShut Down OUT of Range Signal NGThermal Alert FAN FailureSerial Communications RS-232 Connection and Port ConfigurationSerial Command Syntax ExampleInput Select Note Command Value Range DescriptionMinimum Maximum Aspect RatioPicture-in-Picture PIP VideoAudio MSTS10 MSTS08MSTS09 Side-by-side, full height main screen SET-UP Menu CommandsSets 2-screen operation to 2 Screen On leftLOW HighAuto Option Menu CommandsAverage Picture Menu Commands Installer Adjust Mode Option Menu Commands Installer Adjust Mode Screen Menu Commands Installer Adjust ModeSET-UP Menu Commands Installer Adjust Mode FMKS03 FMKS00FMKS02 FMKS044F 53 44 53 30 Sets OSD Display to OFF DWF Minimum Maximum Adjustment CommandsDW1 UPFSpecifications CinemaWall SpecificationsSpecifications are subject to change without notice Date of delivery to the end userDimensions CinemaWallCinemaWall Model SP-50 Dimensions with Optional Table Stand CinemaWall Model SP-60 Dimensions with Optional Table Stand Remarks Computer/Video Signal CompatibilityInput Refresh Rate Resolution Horiz56.0 45.1 Page Page Runco CL-810 Owner’s Operating Manual