Runco SP-50, SP-42, SP-60 manual Quick Setup, Step Procedure For Details, refer to

Page 25

Installation

Table 3-1gives a quick overview of the CinemaWall installation process. The sections following this one provide detailed instructions.

 

Note

Installation should be performed by a qualified custom video

 

installation specialist.

 

Table 3-1. Installation Overview

 

 

 

 

 

 

Step

 

 

Procedure

For Details, refer to

 

 

page...

 

 

 

 

 

 

 

 

1

 

Mount the CinemaWall on a wall or table stand

16

 

 

 

 

2

 

Connect signal sources to the CinemaWall

19

 

 

 

 

3

 

Connect external controller to RS-232 port (optional)

25

 

 

 

 

4

 

Apply power to the CinemaWall

27

 

 

 

 

5

 

Change the OSD language, if desired

27

 

 

 

 

6

 

If using the CinemaWall with a computer, adjust computer

28

 

 

display properties

 

 

 

 

 

7

 

Display calibration: adjust the following for each input;

34 through 40

 

 

save settings when finished:

 

 

 

• Aspect ratio

 

 

 

 

• Brightness

 

 

 

 

• Contrast

 

 

 

 

• Color level

 

 

 

 

• Tint

 

 

 

 

• Sharpness

 

 

 

 

 

 

 

3.2

Quick Setup

Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual

15

Page 24 Page 26
Image 25
Page 24 Page 26
Contents SP-42 SP-50 SP-60 Page For Plasma Displays Three Year Limited WarrantyRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions Table of Contents Specifications Maintenance and TroubleshootingOperation Serial CommunicationsList of Figures Page About This Manual IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories Controls and Functions Controls and IndicatorsCinemaWall at a Glance Display Stand SP-42, SP-50 and SP-60 respectively ConnectorsSP-50 Connector Panel Combination IN/OUT Main Power Switch CinemaWall Remote ControlSET Button Page Remote Control InstallationOther surfaces Step Procedure For Details, refer to Quick SetupConsiderations InstallationHigh-Altitude Operation Mounting the CinemaWallVentilation Ambient LightInstallation Video Connections Connections to the CinemaWallAnalog RGB OUT Input 1 Connection Standby modeComposite or S-Video Input 3 Connection Computer/Video Signal Compatibility onComponent Video Input 4 Connection Attaching the Small Ferrite Cores to Audio Cables Audio Connections11. Audio Output Connection Connection RS-232 ControllerPage Operation Turning on the PowerChanging the OSD Language Setting the Computer Display Properties Selecting an Input Source Viewing Input Signal InformationChanging the Aspect Ratio Aspect Ratio Description Aspect Ratio SettingsPIX by PIX Installer Adjust menu is intended for use by authorized Using the On-Screen MenusTrained service personnel only CinemaWall OSD Menu Structure Picture Main MenuTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Screen Set-Up PowerOFF DVI Setup Option Language Refer to Changing the OSD Language onUnder some conditions such as when the input signal consists Installer ADJ Input Option Installer Adjust ModeFAN Speed Auto ISF CCC color mode is pre-set to approximately 3,200K This action is not undoable. Proceed with caution Seamless Switch is not available when using PIPTo use PIP, press the Split button Using Picture-In-Picture PIPPIP Windows Swapping the MainViewing an Enlarged Area of the Display Enlarging One Part of the ScreenPage Cleaning Maintenance and TroubleshootingTroubleshooting Tips Cleaning the Display Panel Body and Remote ControlThermal Alert OUT of Range Signal NGShut Down FAN FailureSerial Command Syntax RS-232 Connection and Port ConfigurationSerial Communications ExampleMinimum Maximum Command Value Range DescriptionInput Select Note Aspect RatioAudio VideoPicture-in-Picture PIP MSTS09 MSTS08MSTS10 Sets 2-screen operation to 2 Screen SET-UP Menu CommandsSide-by-side, full height main screen On leftHigh LOWAverage Option Menu CommandsAuto Picture Menu Commands Installer Adjust Mode SET-UP Menu Commands Installer Adjust Mode Screen Menu Commands Installer Adjust ModeOption Menu Commands Installer Adjust Mode FMKS02 FMKS00FMKS03 FMKS044F 53 44 53 30 Sets OSD Display to OFF DW1 Minimum Maximum Adjustment CommandsDWF UPFCinemaWall Specifications SpecificationsDate of delivery to the end user Specifications are subject to change without noticeCinemaWall DimensionsCinemaWall Model SP-50 Dimensions with Optional Table Stand CinemaWall Model SP-60 Dimensions with Optional Table Stand Input Refresh Rate Resolution Computer/Video Signal CompatibilityRemarks Horiz56.0 45.1 Page Page Runco CL-810 Owner’s Operating Manual
Top Page Image Contents