Runco SP-50, SP-42, SP-60 manual Installation

Page 28

Installation

Other Considerations ➤ Other considerations and tips that can help improve your installation, avoid damage and prolong operating life:

•Keep the ambient temperature constant and below 35°C (95°F). Keep the display away from heating and/or air conditioning vents. Changes in temperature may cause drifts in the display circuitry, which may affect performance.

•Keep the CinemaWall away from devices that radiate electromagnetic energy such as motors and transformers. Common sources of these include slide projectors, speakers, power amplifiers and elevators.

•Handle the unit carefully when installing it. When carrying it, use the built-in handles; DO NOT touch or hold the screen face.

•Set the unit away from heat, excessive dust, and direct sunlight.

•Protect the inside of the unit from liquids and small metal objects. In case of accident, unplug the power cord and have it serviced by an authorized Runco Service Center.

•Do not hit or scratch the panel surface as this causes flaws on the surface of the screen.

•For correct installation and mounting it is strongly recommended to use a trained, authorized dealer.

•To avoid sulfurization, it is strongly recommended not to place the unit in a dressing room in a public bath or hot spring bath.

18 Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual

Image 28

Contents SP-42 SP-50 SP-60 Page Three Year Limited Warranty For Plasma DisplaysRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions Table of Contents Maintenance and Troubleshooting SpecificationsOperation Serial CommunicationsList of Figures Page Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Functions Controls and IndicatorsCinemaWall at a Glance Display Stand Connectors SP-42, SP-50 and SP-60 respectivelySP-50 Connector Panel Combination IN/OUT CinemaWall Remote Control Main Power SwitchSET Button Page Installation Remote ControlOther surfaces Quick Setup Step Procedure For Details, refer toInstallation ConsiderationsHigh-Altitude Operation Mounting the CinemaWallAmbient Light VentilationInstallation Connections to the CinemaWall Video ConnectionsStandby mode Analog RGB OUT Input 1 ConnectionComputer/Video Signal Compatibility on Composite or S-Video Input 3 ConnectionComponent Video Input 4 Connection Audio Connections Attaching the Small Ferrite Cores to Audio Cables11. Audio Output Connection RS-232 Controller ConnectionPage Operation Turning on the PowerChanging the OSD Language Selecting an Input Source Viewing Input Signal Information Setting the Computer Display PropertiesChanging the Aspect Ratio Aspect Ratio Settings Aspect Ratio DescriptionPIX by PIX Installer Adjust menu is intended for use by authorized Using the On-Screen MenusTrained service personnel only CinemaWall OSD Menu Structure Main Menu PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Screen Set-Up PowerOFF DVI Setup Language Refer to Changing the OSD Language on OptionUnder some conditions such as when the input signal consists Option Installer Adjust Mode Installer ADJ InputFAN Speed Auto ISF CCC color mode is pre-set to approximately 3,200K Seamless Switch is not available when using PIP This action is not undoable. Proceed with cautionUsing Picture-In-Picture PIP To use PIP, press the Split buttonSwapping the Main PIP WindowsEnlarging One Part of the Screen Viewing an Enlarged Area of the DisplayPage Maintenance and Troubleshooting CleaningTroubleshooting Tips Cleaning the Display Panel Body and Remote ControlOUT of Range Signal NG Thermal AlertShut Down FAN FailureRS-232 Connection and Port Configuration Serial Command SyntaxSerial Communications ExampleCommand Value Range Description Minimum MaximumInput Select Note Aspect RatioAudio VideoPicture-in-Picture PIP MSTS09 MSTS08MSTS10 SET-UP Menu Commands Sets 2-screen operation to 2 ScreenSide-by-side, full height main screen On leftLOW HighAverage Option Menu CommandsAuto Picture Menu Commands Installer Adjust Mode SET-UP Menu Commands Installer Adjust Mode Screen Menu Commands Installer Adjust ModeOption Menu Commands Installer Adjust Mode FMKS00 FMKS02FMKS03 FMKS044F 53 44 53 30 Sets OSD Display to OFF Minimum Maximum Adjustment Commands DW1DWF UPFSpecifications CinemaWall SpecificationsSpecifications are subject to change without notice Date of delivery to the end userDimensions CinemaWallCinemaWall Model SP-50 Dimensions with Optional Table Stand CinemaWall Model SP-60 Dimensions with Optional Table Stand Computer/Video Signal Compatibility Input Refresh Rate ResolutionRemarks Horiz56.0 45.1 Page Page Runco CL-810 Owner’s Operating Manual