Runco SP-42, SP-50, SP-60 manual SET Button

Page 21

Controls and Functions

3.MENU

Press this button to show or hide the OSD controls.

4.Directional Buttons ( / / / )

Use these buttons to navigate the OSD menus and adjust various settings.

5.SET BUTTON

Press this button to adjust or enter various settings on the unit.

6.SUB INPUT

When using the Picture-in-Picture (PIP) feature, press this button repeatedly to select a sub-input source.

7.SPLIT

Press this button to change the PIP mode (picture-in-picture, side-by-side or off).

8.MUTE

Press this button to mute the speakers connected to the CinemaWall speaker outputs. Press it again to restore the sound.

9.P-OFF (pin hole)

Using a straightened paper clip or similar object, press this button to program a discrete IR code for powering off the CinemaWall into a control/automation system.

10.RGB SETUP

When using INPUT 1 to display images from a computer, press this button to automatically set the Position, Clock and Phase settings to their optimum values.

11.STANDBY/ON ( )

Press to put the display into operation or standby mode.

12.INFO

Displays currently-selected input, aspect ratio and signal timing information.

13.INSTALLER ADJUST (pin hole)

Used to access the INSTALLER ADJUST menus.

14.MAGNIFY

Press this button to select and enlarge one part of the screen image.

15.SWAP

When using the Picture-in-Picture (PIP) feature, press this button to replace the main screen with the sub-screen or vice versa.

16.PIP SHIFT

Press this button to change the position of the smaller PIP sub-window (lower right, upper right, lower left or upper left).

17.VOLUME + / -

Use these buttons to increase or decrease the volume of sound from the speakers.

18.CLEAR (pin hole)

Using a straightened paper clip or similar object, press this button to clear a screen maintenance program (refer to Program Timer (SP-42) / Screen Maint. (SP-50/SP-60)on page 43).

19.P-ON (pin hole)

Using a straightened paper clip or similar object, press this button to program a discrete IR code for powering on the CinemaWall into a control/automation system.

Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual

11

Image 21

Contents SP-42 SP-50 SP-60 Page For Plasma Displays Three Year Limited WarrantyRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions Table of Contents Specifications Maintenance and TroubleshootingOperation Serial CommunicationsList of Figures Page About This Manual IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories Controls and Indicators Controls and FunctionsCinemaWall at a Glance Display Stand SP-42, SP-50 and SP-60 respectively ConnectorsSP-50 Connector Panel Combination IN/OUT Main Power Switch CinemaWall Remote ControlSET Button Page Remote Control InstallationOther surfaces Step Procedure For Details, refer to Quick SetupConsiderations InstallationHigh-Altitude Operation Mounting the CinemaWallVentilation Ambient LightInstallation Video Connections Connections to the CinemaWallAnalog RGB OUT Input 1 Connection Standby modeComposite or S-Video Input 3 Connection Computer/Video Signal Compatibility onComponent Video Input 4 Connection Attaching the Small Ferrite Cores to Audio Cables Audio Connections11. Audio Output Connection Connection RS-232 ControllerPage Turning on the Power OperationChanging the OSD Language Setting the Computer Display Properties Selecting an Input Source Viewing Input Signal InformationChanging the Aspect Ratio Aspect Ratio Description Aspect Ratio SettingsPIX by PIX Using the On-Screen Menus Installer Adjust menu is intended for use by authorizedTrained service personnel only CinemaWall OSD Menu Structure Picture Main MenuTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Screen Power Set-UpOFF DVI Setup Option Language Refer to Changing the OSD Language onUnder some conditions such as when the input signal consists Installer ADJ Input Option Installer Adjust ModeFAN Speed Auto ISF CCC color mode is pre-set to approximately 3,200K This action is not undoable. Proceed with caution Seamless Switch is not available when using PIPTo use PIP, press the Split button Using Picture-In-Picture PIPPIP Windows Swapping the MainViewing an Enlarged Area of the Display Enlarging One Part of the ScreenPage Cleaning Maintenance and TroubleshootingTroubleshooting Tips Cleaning the Display Panel Body and Remote ControlThermal Alert OUT of Range Signal NGShut Down FAN FailureSerial Command Syntax RS-232 Connection and Port ConfigurationSerial Communications ExampleMinimum Maximum Command Value Range DescriptionInput Select Note Aspect RatioVideo AudioPicture-in-Picture PIP MSTS08 MSTS09MSTS10 Sets 2-screen operation to 2 Screen SET-UP Menu CommandsSide-by-side, full height main screen On leftHigh LOWOption Menu Commands AverageAuto Picture Menu Commands Installer Adjust Mode Screen Menu Commands Installer Adjust Mode SET-UP Menu Commands Installer Adjust ModeOption Menu Commands Installer Adjust Mode FMKS02 FMKS00FMKS03 FMKS044F 53 44 53 30 Sets OSD Display to OFF DW1 Minimum Maximum Adjustment CommandsDWF UPFCinemaWall Specifications SpecificationsDate of delivery to the end user Specifications are subject to change without noticeCinemaWall DimensionsCinemaWall Model SP-50 Dimensions with Optional Table Stand CinemaWall Model SP-60 Dimensions with Optional Table Stand Input Refresh Rate Resolution Computer/Video Signal CompatibilityRemarks Horiz56.0 45.1 Page Page Runco CL-810 Owner’s Operating Manual