Runco SP-60, SP-42, SP-50 manual Component Video Input 4 Connection

Page 32

Installation

Component Video (INPUT 4) Connection: If you have a DVD player or DTV decoder with a component (YPbPr) output, connect it to INPUT 4 as shown in Figure 3-7.

Tip	For best results, use INPUT 4 for 480p and higher-resolution sources
	only. (Use INPUT 3 for standard-definition (480i) sources).

COMPONENT

Figure 3-7. Component Video (INPUT 4) Connection

DVI-D Video (INPUT 5) Connection: The CinemaWall has a DVI-D input for connecting a DVD player, DTV decoder or any other device with a DVI output (computer signals are not supported). Connect such devices to INPUT 5 as shown in Figure 3-8.Use a 24-pin, DVI-D (digital only) cable.

DVI VIDEO

COMPONENT

Figure 3-8. DVI-D (INPUT 5) Connection

22 Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual

Image 32

Contents SP-42 SP-50 SP-60 Page Three Year Limited Warranty For Plasma DisplaysRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions Table of Contents Maintenance and Troubleshooting SpecificationsOperation Serial CommunicationsList of Figures Page Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories CinemaWall at a Glance Controls and IndicatorsControls and Functions Display Stand Connectors SP-42, SP-50 and SP-60 respectivelySP-50 Connector Panel Combination IN/OUT CinemaWall Remote Control Main Power SwitchSET Button Page Installation Remote ControlOther surfaces Quick Setup Step Procedure For Details, refer toInstallation ConsiderationsHigh-Altitude Operation Mounting the CinemaWallAmbient Light VentilationInstallation Connections to the CinemaWall Video ConnectionsStandby mode Analog RGB OUT Input 1 ConnectionComputer/Video Signal Compatibility on Composite or S-Video Input 3 ConnectionComponent Video Input 4 Connection Audio Connections Attaching the Small Ferrite Cores to Audio Cables11. Audio Output Connection RS-232 Controller ConnectionPage Changing the OSD Language Turning on the PowerOperation Selecting an Input Source Viewing Input Signal Information Setting the Computer Display PropertiesChanging the Aspect Ratio Aspect Ratio Settings Aspect Ratio DescriptionPIX by PIX Trained service personnel only Using the On-Screen MenusInstaller Adjust menu is intended for use by authorized CinemaWall OSD Menu Structure Main Menu PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Screen OFF PowerSet-Up DVI Setup Language Refer to Changing the OSD Language on OptionUnder some conditions such as when the input signal consists Option Installer Adjust Mode Installer ADJ InputFAN Speed Auto ISF CCC color mode is pre-set to approximately 3,200K Seamless Switch is not available when using PIP This action is not undoable. Proceed with cautionUsing Picture-In-Picture PIP To use PIP, press the Split buttonSwapping the Main PIP WindowsEnlarging One Part of the Screen Viewing an Enlarged Area of the DisplayPage Maintenance and Troubleshooting CleaningTroubleshooting Tips Cleaning the Display Panel Body and Remote ControlOUT of Range Signal NG Thermal AlertShut Down FAN FailureRS-232 Connection and Port Configuration Serial Command SyntaxSerial Communications ExampleCommand Value Range Description Minimum MaximumInput Select Note Aspect RatioPicture-in-Picture PIP VideoAudio MSTS10 MSTS08MSTS09 SET-UP Menu Commands Sets 2-screen operation to 2 ScreenSide-by-side, full height main screen On leftLOW HighAuto Option Menu CommandsAverage Picture Menu Commands Installer Adjust Mode Option Menu Commands Installer Adjust Mode Screen Menu Commands Installer Adjust ModeSET-UP Menu Commands Installer Adjust Mode FMKS00 FMKS02FMKS03 FMKS044F 53 44 53 30 Sets OSD Display to OFF Minimum Maximum Adjustment Commands DW1DWF UPFSpecifications CinemaWall SpecificationsSpecifications are subject to change without notice Date of delivery to the end userDimensions CinemaWallCinemaWall Model SP-50 Dimensions with Optional Table Stand CinemaWall Model SP-60 Dimensions with Optional Table Stand Computer/Video Signal Compatibility Input Refresh Rate ResolutionRemarks Horiz56.0 45.1 Page Page Runco CL-810 Owner’s Operating Manual