Runco SP-60, SP-42, SP-50 manual DVI Setup

Page 50

Operation

DVI SETUP

PLUG/PLAY

:

VIDEO

BLACK LEVEL

:

LOW

 

 

 

 

 

 

SET ENTER

MENU

EXIT

 

 

 

Use the left- or right-arrow buttons to select the desired amount of noise reduction, keeping in mind that higher settings (which reduce high frequencies) may also “soften” the image.

MPEG Filter: Use the MPEG Filter to reduce or eliminate so-called “mosquito noise” in MPEG-compressed video signals (digital broadcasts or DVDs). Set it to LOW, MIDDLE or HIGH, as needed to minimize distortion around the edges of moving objects, moving artifacts around edges and/or blotchy noise patterns superimposed over the objects.

Chroma EE: Use the Chroma EE control to correct chroma delay in a Composite, S-Video or Component video source. Chroma delay in an image causes color shifts to occur to the left of the vertical edge transitions, producing artificial shadows or a “halo” effect. If necessary, set Chroma EE to ON to eliminate them.

Film Mode: When you enable Film Mode, the CinemaWall automatically detects and optimizes the display of interlaced video signals that originated from film. To disable Film Mode, set it to OFF.

Film Mode can only be used on input signals with a 60-Hz refresh

Note rate.

Color Space: To ensure proper color reproduction, select Color Space from the Set-Up menu and set it as follows:

Select RGB for RGB input signals from a computer or video deck.

Select COMP. 1 for component input signals less than 720p, such as from a DVD player.

Select COMP. 2 for higher-resolution component input signals (720p or above, such as from an HD tuner).

DVI Setup (Input 2 only): Select DVI Setup from the Set-Up menu to configure Input 2 for “plug-and-play” operation with a computer, and select the appropriate black level.

Plug/Play: If the Input 2 source is a computer, set this to PC. Otherwise, set it to Video.

Black Level: This control compensates for incoming elevated black levels present in certain video signals. Generally, the CinemaWall automatically determines the best setting according to the incoming video signal type. For some types of video, you may want to override the setting. Set it to LOW if blacks appear elevated (dark gray). If blacks appear “crushed” (too dark), set it to HIGH.

Signal: The CinemaWall automatically identifies PC signals and video signals according to the frequency of the input signal, and identifies the resolution of a PC signal.

In most cases, setting Signal to Auto works well. However, if the displayed image is unstable or distorted, select Signal from the Set-Up menu and select a specific signal format. The available choices vary for each input.

Brt. Enhance (Installer Adjust mode): To improve and enhance the brightness of the center of the screen, select Brt. Enhance from the Set-Up menu and set it to ON. This reduces the brightness of the outer areas of the display by about 3 to 5%, relative to the center. For uniform brightness over the entire screen area, set Brt. Enhance to OFF.

40 Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual

Image 50
Contents SP-42 SP-50 SP-60 Page Three Year Limited Warranty For Plasma DisplaysRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation Maintenance and TroubleshootingSpecifications Serial CommunicationsList of Figures Page Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories CinemaWall at a Glance Controls and IndicatorsControls and Functions Display Stand Connectors SP-42, SP-50 and SP-60 respectivelySP-50 Connector Panel Combination IN/OUT CinemaWall Remote Control Main Power SwitchSET Button Page Installation Remote ControlOther surfaces Quick Setup Step Procedure For Details, refer toHigh-Altitude Operation InstallationConsiderations Mounting the CinemaWallAmbient Light VentilationInstallation Connections to the CinemaWall Video ConnectionsStandby mode Analog RGB OUT Input 1 ConnectionComputer/Video Signal Compatibility on Composite or S-Video Input 3 ConnectionComponent Video Input 4 Connection Audio Connections Attaching the Small Ferrite Cores to Audio Cables11. Audio Output Connection RS-232 Controller ConnectionPage Changing the OSD Language Turning on the PowerOperation Selecting an Input Source Viewing Input Signal Information Setting the Computer Display PropertiesChanging the Aspect Ratio Aspect Ratio Settings Aspect Ratio DescriptionPIX by PIX Trained service personnel only Using the On-Screen MenusInstaller Adjust menu is intended for use by authorized CinemaWall OSD Menu Structure Main Menu PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Screen OFF PowerSet-Up DVI Setup Language Refer to Changing the OSD Language on OptionUnder some conditions such as when the input signal consists Option Installer Adjust Mode Installer ADJ InputFAN Speed Auto ISF CCC color mode is pre-set to approximately 3,200K Seamless Switch is not available when using PIP This action is not undoable. Proceed with cautionUsing Picture-In-Picture PIP To use PIP, press the Split buttonSwapping the Main PIP WindowsEnlarging One Part of the Screen Viewing an Enlarged Area of the DisplayPage Troubleshooting Tips Maintenance and TroubleshootingCleaning Cleaning the Display Panel Body and Remote ControlShut Down OUT of Range Signal NGThermal Alert FAN FailureSerial Communications RS-232 Connection and Port ConfigurationSerial Command Syntax ExampleInput Select Note Command Value Range DescriptionMinimum Maximum Aspect RatioPicture-in-Picture PIP VideoAudio MSTS10 MSTS08MSTS09 Side-by-side, full height main screen SET-UP Menu CommandsSets 2-screen operation to 2 Screen On leftLOW HighAuto Option Menu CommandsAverage Picture Menu Commands Installer Adjust Mode Option Menu Commands Installer Adjust Mode Screen Menu Commands Installer Adjust ModeSET-UP Menu Commands Installer Adjust Mode FMKS03 FMKS00FMKS02 FMKS044F 53 44 53 30 Sets OSD Display to OFF DWF Minimum Maximum Adjustment CommandsDW1 UPFSpecifications CinemaWall SpecificationsSpecifications are subject to change without notice Date of delivery to the end userDimensions CinemaWallCinemaWall Model SP-50 Dimensions with Optional Table Stand CinemaWall Model SP-60 Dimensions with Optional Table Stand Remarks Computer/Video Signal CompatibilityInput Refresh Rate Resolution Horiz56.0 45.1 Page Page Runco CL-810 Owner’s Operating Manual