Runco SP-60, SP-42, SP-50 manual Installation, Remote Control

Page 23

3. Installation

To install batteries in the remote control:	While pressing down lightly, slide
1. Remove the battery cover from the	in the direction of the arrow.
1. Remove the battery cover from the
back of the remote control.

2.Insert the batteries included with the remote control. Ensure that the

	polarities correctly match the	and	Two AA (R6)
	polarities correctly match the	and	batteries
	markings inside the battery		batteries
	markings inside the battery
	compartment.

3. Replace the battery cover.

•When installing batteries, make sure that the battery polarities are correct.

•Do not mix an old battery with a new one or different types of batteries.

•If you will not use the remote control for a long time, remove the batteries to avoid damage from battery leakage.

The remote control can be used to control the CinemaWall within the ranges shown in Figure 3-1.

3.1

Remote Control

Notes on Batteries

Notes on Remote Control Operation

7 m

(23 feet)

30°

30°

Remote Sensor

Figure 3-1.Available Range of the Remote Control

Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual

13

Image 23

Contents SP-42 SP-50 SP-60 Page For Plasma Displays Three Year Limited WarrantyRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions Table of Contents Serial Communications Maintenance and TroubleshootingSpecifications OperationList of Figures Page About This Manual IntroductionIf you need Turn to Using This ManualKey Features and Benefits Description, Features and BenefitsOptional Accessories CinemaWall at a Glance Controls and IndicatorsControls and Functions Display Stand SP-42, SP-50 and SP-60 respectively ConnectorsSP-50 Connector Panel Combination IN/OUT Main Power Switch CinemaWall Remote ControlSET Button Page Remote Control InstallationOther surfaces Step Procedure For Details, refer to Quick SetupMounting the CinemaWall InstallationConsiderations High-Altitude OperationVentilation Ambient LightInstallation Video Connections Connections to the CinemaWallAnalog RGB OUT Input 1 Connection Standby modeComposite or S-Video Input 3 Connection Computer/Video Signal Compatibility onComponent Video Input 4 Connection Attaching the Small Ferrite Cores to Audio Cables Audio Connections11. Audio Output Connection Connection RS-232 ControllerPage Changing the OSD Language Turning on the PowerOperation Setting the Computer Display Properties Selecting an Input Source Viewing Input Signal InformationChanging the Aspect Ratio Aspect Ratio Description Aspect Ratio SettingsPIX by PIX Trained service personnel only Using the On-Screen MenusInstaller Adjust menu is intended for use by authorized CinemaWall OSD Menu Structure Picture Main MenuTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Screen OFF PowerSet-Up DVI Setup Option Language Refer to Changing the OSD Language onUnder some conditions such as when the input signal consists Installer ADJ Input Option Installer Adjust ModeFAN Speed Auto ISF CCC color mode is pre-set to approximately 3,200K This action is not undoable. Proceed with caution Seamless Switch is not available when using PIPTo use PIP, press the Split button Using Picture-In-Picture PIPPIP Windows Swapping the MainViewing an Enlarged Area of the Display Enlarging One Part of the ScreenPage Cleaning the Display Panel Body and Remote Control Maintenance and TroubleshootingCleaning Troubleshooting TipsFAN Failure OUT of Range Signal NGThermal Alert Shut DownExample RS-232 Connection and Port ConfigurationSerial Command Syntax Serial CommunicationsAspect Ratio Command Value Range DescriptionMinimum Maximum Input Select NotePicture-in-Picture PIP VideoAudio MSTS10 MSTS08MSTS09 On left SET-UP Menu CommandsSets 2-screen operation to 2 Screen Side-by-side, full height main screenHigh LOWAuto Option Menu CommandsAverage Picture Menu Commands Installer Adjust Mode Option Menu Commands Installer Adjust Mode Screen Menu Commands Installer Adjust ModeSET-UP Menu Commands Installer Adjust Mode FMKS04 FMKS00FMKS02 FMKS034F 53 44 53 30 Sets OSD Display to OFF UPF Minimum Maximum Adjustment CommandsDW1 DWFCinemaWall Specifications SpecificationsDate of delivery to the end user Specifications are subject to change without noticeCinemaWall DimensionsCinemaWall Model SP-50 Dimensions with Optional Table Stand CinemaWall Model SP-60 Dimensions with Optional Table Stand Horiz Computer/Video Signal CompatibilityInput Refresh Rate Resolution Remarks56.0 45.1 Page Page Runco CL-810 Owner’s Operating Manual