Runco SP-60, SP-42, SP-50 manual Main Menu, Picture

Page 44

Operation

			Main Menu ➤
				Picture ➤

CINEMAWALL					INPUT 3
	PICTURE	SCREEN SET-UP OPTION
	CONTRAST		: 0
	BRIGHTNESS		: 0
	COLOR		: 0
	TINT		: 0
	TINT		: 0
	SHARPNESS		: 0
	FACTORY
	SET	ENTER			MENU EXIT

INSTALLER ADJUST					INPUT 3
PICTURE	SCREEN	SET-UP		OPTION
CONTRAST		: +128
BRIGHTNESS		: +128
COLOR		:	+64
TINT		:	+30
SHARPNESS		:	+8
WHITE BALANCE
COLOR CHART
GAMMA		:	2.2
FACTORY
SET	ENTER			MENU	EXIT

The Main Menu is the starting point for accessing all CinemaWall functions. Some menu options are available only in “Installer Adjust” mode.

Use the controls in the Picture menu to calibrate your CinemaWall for optimum picture quality.

The CinemaWall has been designed to incorporate setup and calibration standards established by the Imaging Science Foundation (ISF). The ISF has developed carefully crafted, industry-recognized standards for optimal video performance and has implemented a training program for technicians and installers to use these standards to obtain optimal picture quality from Runco video display devices. Accordingly, Runco recommends that setup and calibration be performed by an ISF-certified installation technician.

All signal types require separate processing. Therefore, you need to calibrate each input separately.

Although it may be possible to obtain satisfactory picture quality using the naked eye and regular program material, Runco recommends using the following calibration tools for best results:

•External test pattern source – Ovation Multimedia, Video Essentials or AVIA test DVD (or equivalent).

•A blue filter (provided with many test DVDs), for color level and tint adjustments.

Connect your test pattern source to the input that you are calibrating and proceed as follows. Perform the adjustments in the order listed here.

Brightness: On your external test pattern source, select a PLUGE pattern. (PLUGE is an acronym for “Picture Line-Up Generation Equipment.”) Figure 4-3shows a typical PLUGE pattern.

Below Black

Above Black

Figure 4-3. Typical PLUGE Pattern for Adjusting Brightness

34 Runco CinemaWall SP-42/-50/-60 Owner’s Operating Manual

Image 44

Contents SP-42 SP-50 SP-60 Page Three Year Limited Warranty For Plasma DisplaysRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions Table of Contents Maintenance and Troubleshooting SpecificationsOperation Serial CommunicationsList of Figures Page Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories CinemaWall at a Glance Controls and IndicatorsControls and Functions Display Stand Connectors SP-42, SP-50 and SP-60 respectivelySP-50 Connector Panel Combination IN/OUT CinemaWall Remote Control Main Power SwitchSET Button Page Installation Remote ControlOther surfaces Quick Setup Step Procedure For Details, refer toInstallation ConsiderationsHigh-Altitude Operation Mounting the CinemaWallAmbient Light VentilationInstallation Connections to the CinemaWall Video ConnectionsStandby mode Analog RGB OUT Input 1 ConnectionComputer/Video Signal Compatibility on Composite or S-Video Input 3 ConnectionComponent Video Input 4 Connection Audio Connections Attaching the Small Ferrite Cores to Audio Cables11. Audio Output Connection RS-232 Controller ConnectionPage Changing the OSD Language Turning on the PowerOperation Selecting an Input Source Viewing Input Signal Information Setting the Computer Display PropertiesChanging the Aspect Ratio Aspect Ratio Settings Aspect Ratio DescriptionPIX by PIX Trained service personnel only Using the On-Screen MenusInstaller Adjust menu is intended for use by authorized CinemaWall OSD Menu Structure Main Menu PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Typical Test Pattern for Adjusting Sharpness Screen OFF PowerSet-Up DVI Setup Language Refer to Changing the OSD Language on OptionUnder some conditions such as when the input signal consists Option Installer Adjust Mode Installer ADJ InputFAN Speed Auto ISF CCC color mode is pre-set to approximately 3,200K Seamless Switch is not available when using PIP This action is not undoable. Proceed with cautionUsing Picture-In-Picture PIP To use PIP, press the Split buttonSwapping the Main PIP WindowsEnlarging One Part of the Screen Viewing an Enlarged Area of the DisplayPage Maintenance and Troubleshooting CleaningTroubleshooting Tips Cleaning the Display Panel Body and Remote ControlOUT of Range Signal NG Thermal AlertShut Down FAN FailureRS-232 Connection and Port Configuration Serial Command SyntaxSerial Communications ExampleCommand Value Range Description Minimum MaximumInput Select Note Aspect RatioPicture-in-Picture PIP VideoAudio MSTS10 MSTS08MSTS09 SET-UP Menu Commands Sets 2-screen operation to 2 ScreenSide-by-side, full height main screen On leftLOW HighAuto Option Menu CommandsAverage Picture Menu Commands Installer Adjust Mode Option Menu Commands Installer Adjust Mode Screen Menu Commands Installer Adjust ModeSET-UP Menu Commands Installer Adjust Mode FMKS00 FMKS02FMKS03 FMKS044F 53 44 53 30 Sets OSD Display to OFF Minimum Maximum Adjustment Commands DW1DWF UPFSpecifications CinemaWall SpecificationsSpecifications are subject to change without notice Date of delivery to the end userDimensions CinemaWallCinemaWall Model SP-50 Dimensions with Optional Table Stand CinemaWall Model SP-60 Dimensions with Optional Table Stand Computer/Video Signal Compatibility Input Refresh Rate ResolutionRemarks Horiz56.0 45.1 Page Page Runco CL-810 Owner’s Operating Manual