Panasonic WV-CU161 operating instructions Key Functions on the Setup Menu, Alarm Setup

Page 17

Displaying the Setup Menu

• Joystick Controller

1.

Check that the camera, the monitor and peripherals are

 

connected correctly and securely.

2.

Switch all the system components on.

 

The operate indicator of the WV-CU161 lights up.

 

The picture of the camera appears on the monitor.

3.

Press the SHIFT button, and then press the CAMERA

 

SETUP/SETUP button for 2 seconds or more.

4.

The SETUP MENU appears.

WV-CU161 SETUP MENU *.**

ALARM SETUP

L

R

DOWN

UP

L

R

UP

R

DOWN

UP

L

R

Up: To select modes.

Down: To select modes.

Left: To decrease the parameter.

Right: To increase the parameter.

SYSTEM SETUP

PRESET DATA LOAD

COMMUNICATION

Note: The COMMUNICATION parameter appears when the data switch is set to RS-485 (See page 9).

Key Functions on the Setup Menu

SHIFT button + CAMERA SETUP/SETUP/PROGRAM button:

To display the program menu. Press CAMERA SETUP /SETUP button for 2 seconds or more after pressing the SHIFT button.

 

CAMERA

 

SETUP

SHIFT

SETUP

PROGRAM

PRESET/SET/PROGRAM PRESET button:

To execute modes and parameters.

To enter a submenu for an item marked .

PRESET

SET

PROGRAM

PRESET

HOME/ESC button:

To return to the previous menu.

HOME

ESC

DOWN

Closing Setup Menu

Press the SHIFT button, and then press the PRESET/ SET/PROGRAM PRESET button for 2 seconds or more. The LED next to the button goes off.

Notes:

When the power of the WV-CU161 is turned off before completing the setup, the new values do not become valid. The saved values remain valid until new values are saved.

After parameters have been changed, return to the Setup menu, and then turn the power off.

Alarm Setup

1.Display the Setup menu.

2.Select ALARM SETUP by moving the joystick up or down.

3.Press the PRESET/SET/PROGRAM PRESET button.

The ALARM SETUP menu appears on the monitor as shown below.

For using alarm input/output terminal and alarm recover input/output terminal

ALARM SETUP

ALARM DISPLAY ON

SITE ALARM ON

TERM.ALARM ON

ALARM OUTPUT 10S

ALARM BUZZER ON

ALARM PRESET –

17

Image 17
Contents Operating Instructions English Version Contents Preface FeaturesDo not drop metallic parts through slots PrecautionsDo not attempt to disassemble the appliance Handle the appliance with careAlarm Indicator Alarm Operate Indicator OperateJoystick Controller UP/DOWN/L/R Patrol Play/Patrol Learn Button Patrol Play4Alarm Reset/Suspend Button 1Preset/Set/Program Preset Button5Camera Setup/Setup/Program Button Wiper/Auxiliary 1 Button WIPER/AUX1Alarm Output Terminal Alarm OUT Alarm Input Terminal AlarmGround Terminal G Recover Input Terminal Recover 0Data Selection Switch COAX/RS485Alarm Switch Setting SetupData Switch Setting Connections DIP Switch SettingBasic System Connection System ConnectionData Connection with a Video SwitcherTerm Line Connection with a Time Lapse VCR Cable-loss Compensation SettingRS-485 Terminal Internal DiagramSetup Menu Alarm Setup Key Functions on the Setup MenuSite Alarm Setting Alarm Display SettingTerminal Alarm Setting Alarm Output SettingSwitch Buzzer Setting System SetupCable Compensation Setting Error Display Preset Data Load SettingDownload Setting Data Title Setting Upload SettingUnit Address Setting Communication SettingBaud Rate Setting Data Bit SettingStop Bit Setting Parity Check SettingWait Time Setting Delay Time SettingLens Control Operating ProceduresPan/Tilt Control Operation of Combination Camera Changing to Picture at Preset PositionAuto Pan Changing to Picture at Home PositionCamera Functions Camera Patrol FunctionSuper Dynamic Electronic ShutterCamera Restart Automatic Gain ControlElectronic Sensitivity Enhancement External Device Control Camera Housing ControlWiper Control Defroster ControlAlarm Suspend Alarm OperationAlarm Reset Camera SETUP/SETUP/PROGRAM button Camera SetupKeys Used in Camera Setup Menu Camera Patrol Learning for Camera Patrol Operation Preset Position SettingMounting in the Rack InstallationALL Reset Specifications Panasonic Canada Inc Operating Instructions Précaution Version FrançaiseTable DES Matières Caractéristiques Dominantes PréraceNe pas manipuler cet appareil brutalement Mesures DE PrécautionNe jamais chercher à démonter lappareil Vue de la face avant Lampe-témoin de cas dalarme AlarmLampe-témoin dalimentation Operate Touche de dégivreur/dappareil auxiliaire 2 DEF/AUX2Touches de ré glage de mise au point Focus NEAR/FAR Touche dessuie-glace/dappareil auxiliaire 1 WIPER/AUX10Touches de pavé numé rique 2Touche de position de dé part/dé chappement HOME/ESCVue de la face arriè re Ré glage du commutateur de transmission de donné es ConfigurationRé glage du sé lecteur dalarme Accè s à linterrupteur SW1 BranchementsBranchement de base Branchement DE Systè MERemarques Raccordement à un commutateur cyclique vidé oCâble RS-485 Câble coaxial Ré glage de compensation de pertes dans les câ bles Sché ma interne Borne RS-485Menu DE Configuration Affichage du menu de configuration Fonctions attribuées aux touches Du menu de configurationConfiguration dalarme Ré glage dalarme de site Ré glage daffichage dalarmeRé glage dalarme de borne Ré glage de sortie dalarmeRé glage de sonnerie de commutateur Configuration de systè meRé glage de compensation de pertes dans les câ bles Affichage derreur Ré glage de chargement de donné es pré sé lectionné esRé glage de titre de donné es Ré glage de té lé chargementRé glage dadresse dappareil Ré glage de communicationRé glage de vitesse de transmission Ré glage de bit de transmissionRé glage de bit darrê t Ré glage de contrô le de paritéRé glage de duré e dattente Ré glage de temporisationProcé Dures Dutilisation Commande dobjectifChangement des images de position pré sé lectionné e Utilisation dune camé ra vidé o de surveillance combiné eChangement des images à la position de dé part Balayage panoramique automatiqueChangement dune image couleurà une image noir et blanc Fonction de patrouille de camé ra vidé o de surveillanceFonctions de camé ra vidé o de surveillance Fonction Super DynamicAccroissement de la sensibilité é lectronique Commande de gain automatiqueCommande dun appareil exté rieur Commande de compartiment de camé ra vidé oCommande dessuie-glace Commande de dé givreurMise en non activité dalarme Dé clenchement dalarmeRemise à zé ro dalarme Touche Camera SETUP/SETUP/PROGRAM Configuration de camé ra vidé o de surveillanceLearning Ré glage de position pré sé lectionné ePanneau latéral Gauche Installation en bâ tiRemise À ZÉ RO GÉ NÉ Rale Caracté Ristiques Techniques Panasonic Canada Inc