Panasonic WV-CU161 System Setup, Cable Compensation Setting, Switch Buzzer Setting

Page 19

• For using alarm input terminals 1-4

ALARM SETUP

ALARM DISPLAY ON

SITE ALARM ON

TERM.ALARM ON

ALARM OUTPUT 10S

ALARM BUZZER ON

ALARM TERMINAL

1.Display the ALARM SETUP menu.

2.Select ALARM TERMINAL by moving the joystick up or down.

3.Press the PRESET/SET/PROGRAM PRESET button. The ALARM TERMINAL screen appears as shown below.

ALARM TERMINAL

ALARM PRESET

1-

2-

3-

4-

4.Select the alarm terminal number by moving the joy- stick up or down.

5.Move the joystick to the right or left to select the desired preset numbers of the picture on the moni- tor in the range of 1-64, or [–] if no preset numbers are assigned.

The initial factory setting is – (No assignment).

1-64:Preset numbers

–:No assignment

6.To return to the previous menu, press the HOME/ESC button.

Notes:

ALARM TERMINAL is available only when a combi- nation camera is connected.

If the camera has the Preset Alarm ON/OFF mode, set it to OFF.

System Setup

1.Display the Setup menu.

2.Select SYSTEM SETUP by moving the joystick up or down.

3.Press the PRESET/SET/PROGRAM PRESET button.

The SYSTEM SETUP menu appears on the monitor as shown below.

SYSTEM SETUP

 

 

CABLE COMP

 

 

S

SWITCH BUZZER

ON

(1) Cable Compensation Setting

This item lets you select the cable length to compensate for transmission loss.

1.Display the SYSTEM SETUP menu.

2.Select CABLE COMP by moving the joystick up or down.

3.Select the most suitable cable length by moving the joy- stick to the right or left.

The initial factory setting is S.

S:Less than 400 m (1 300 ft)

M:400 m (1 300 ft) to 700 m (2 300 ft)

L:700 m (2 300 ft) to 900 m (3 000 ft)

(When using RG-59U, BELDEN 9259 or equivalent cable)

(2)Switch Buzzer Setting

This item lets you select whether or not the switch buzzer sounds when a button is pressed.

1.Display the SYSTEM SETUP menu.

2.Select SWITCH BUZZER by moving the joystick up or down.

3.Select ON or OFF mode by moving the joystick to the right or left.

The initial factory setting is ON.

19

Image 19
Contents Operating Instructions English Version Contents Preface FeaturesHandle the appliance with care PrecautionsDo not drop metallic parts through slots Do not attempt to disassemble the appliancePatrol Play/Patrol Learn Button Patrol Play Operate Indicator OperateAlarm Indicator Alarm Joystick Controller UP/DOWN/L/RWiper/Auxiliary 1 Button WIPER/AUX1 1Preset/Set/Program Preset Button4Alarm Reset/Suspend Button 5Camera Setup/Setup/Program Button0Data Selection Switch COAX/RS485 Alarm Input Terminal AlarmAlarm Output Terminal Alarm OUT Ground Terminal G Recover Input Terminal RecoverData Switch Setting SetupAlarm Switch Setting Connections DIP Switch SettingBasic System Connection System ConnectionData Connection with a Video SwitcherTerm Line Connection with a Time Lapse VCR Cable-loss Compensation SettingRS-485 Terminal Internal DiagramSetup Menu Alarm Setup Key Functions on the Setup MenuAlarm Output Setting Alarm Display SettingSite Alarm Setting Terminal Alarm SettingCable Compensation Setting System SetupSwitch Buzzer Setting Download Setting Preset Data Load SettingError Display Data Title Setting Upload SettingData Bit Setting Communication SettingUnit Address Setting Baud Rate SettingDelay Time Setting Parity Check SettingStop Bit Setting Wait Time SettingPan/Tilt Control Operating ProceduresLens Control Changing to Picture at Home Position Changing to Picture at Preset PositionOperation of Combination Camera Auto PanElectronic Shutter Camera Patrol FunctionCamera Functions Super DynamicElectronic Sensitivity Enhancement Automatic Gain ControlCamera Restart Defroster Control Camera Housing ControlExternal Device Control Wiper ControlAlarm Reset Alarm OperationAlarm Suspend Keys Used in Camera Setup Menu Camera SetupCamera SETUP/SETUP/PROGRAM button Camera Patrol Learning for Camera Patrol Operation Preset Position SettingMounting in the Rack InstallationALL Reset Specifications Panasonic Canada Inc Operating Instructions Précaution Version FrançaiseTable DES Matières Caractéristiques Dominantes PréraceNe jamais chercher à démonter lappareil Mesures DE PrécautionNe pas manipuler cet appareil brutalement Touche de dégivreur/dappareil auxiliaire 2 DEF/AUX2 Lampe-témoin de cas dalarme AlarmVue de la face avant Lampe-témoin dalimentation Operate2Touche de position de dé part/dé chappement HOME/ESC Touche dessuie-glace/dappareil auxiliaire 1 WIPER/AUX1Touches de ré glage de mise au point Focus NEAR/FAR 0Touches de pavé numé riqueVue de la face arriè re Ré glage du sé lecteur dalarme ConfigurationRé glage du commutateur de transmission de donné es Accè s à linterrupteur SW1 BranchementsBranchement de base Branchement DE Systè MERemarques Raccordement à un commutateur cyclique vidé oCâble RS-485 Câble coaxial Ré glage de compensation de pertes dans les câ bles Sché ma interne Borne RS-485Menu DE Configuration Configuration dalarme Fonctions attribuées aux touches Du menu de configurationAffichage du menu de configuration Ré glage de sortie dalarme Ré glage daffichage dalarmeRé glage dalarme de site Ré glage dalarme de borneRé glage de compensation de pertes dans les câ bles Configuration de systè meRé glage de sonnerie de commutateur Affichage derreur Ré glage de chargement de donné es pré sé lectionné esRé glage de titre de donné es Ré glage de té lé chargementRé glage de bit de transmission Ré glage de communicationRé glage dadresse dappareil Ré glage de vitesse de transmissionRé glage de temporisation Ré glage de contrô le de paritéRé glage de bit darrê t Ré glage de duré e dattenteProcé Dures Dutilisation Commande dobjectifBalayage panoramique automatique Utilisation dune camé ra vidé o de surveillance combiné eChangement des images de position pré sé lectionné e Changement des images à la position de dé partFonction Super Dynamic Fonction de patrouille de camé ra vidé o de surveillanceChangement dune image couleurà une image noir et blanc Fonctions de camé ra vidé o de surveillanceAccroissement de la sensibilité é lectronique Commande de gain automatiqueCommande de dé givreur Commande de compartiment de camé ra vidé oCommande dun appareil exté rieur Commande dessuie-glaceRemise à zé ro dalarme Dé clenchement dalarmeMise en non activité dalarme Touche Camera SETUP/SETUP/PROGRAM Configuration de camé ra vidé o de surveillanceLearning Ré glage de position pré sé lectionné ePanneau latéral Gauche Installation en bâ tiRemise À ZÉ RO GÉ NÉ Rale Caracté Ristiques Techniques Panasonic Canada Inc