Panasonic WV-CU161 Camera Patrol Learning for Camera Patrol Operation, Preset Position Setting

Page 31

●Camera Patrol Learning for Camera Patrol Operation

The camera patrol learning function can be setup either from the Camera Setup menu or while operating the cam- era.

Follow the procedures below to setup the function for a connecting combination camera.

1.Press the PATROL PLAY/PATROL LEARN button within approx. 2 seconds while holding down the CAM- ERA SETUP/SETUP/PROGRAM button.

Note: Unless the PATROL PLAY/PATROL LEARN but- ton is pressed within approx. 2 seconds or more after holding down the CAMERA SETUP/SETUP/ PROGRAM button, the screen returns to the Setup menu of the WV-CU161 or the Camera Setup menu.

PATROL

CAMERA

PLAY

SETUP

 

 

SETUP

PATROL LEARN

PROGRAM

[LEARNING] appears on the monitor.

LEARNING

2.Run the camera through a patrol by using the joystick, zoom buttons etc. This combination camera will learn (memorize) the patrol. Maximum learning time is 30 seconds.

3.To stop the learning process, press the AUTO/B/W/ PATROL STOP button while holding down the CAM- ERA SETUP/ SETUP/PROGRAM button.

CAMERA

AUTO

SETUP

SETUP

B/W

PROGRAM

PATROL STOP

[LEARNING] disappears from the monitor. Learning program

•Pan/Tilt (Joystick)

•Iris (Open/Close)

•Focus (Far/Near)

•Zoom (Tele/Wide)

•Preset Position

Note: The learning program differs depending on the camera. For further information, refer to the Operating Instructions for the camera to check the operations covered by the learning program before operating the camera.

●Preset Position Setting

Preset positions can be programmed either from the Camera Setup menu or from the System Controller.

The following functions are available with the respective functions.

1.Move the combination camera to the desired preset position by using the joystick.

UP

LR

DOWN

2.Press the numeric button for the preset position to be learned.

1

2

3

4

5

6

7

8

9

HOME

PRESET

 

0

ESC

 

SET

PROGRAM

PRESET

3.Press the PRESET/SET/PROGRAM PRESET button while holding down the CAMERA SETUP/SETUP/PRO- GRAM button.

 

PRESET

CAMERA

 

SETUP

 

SETUP

SET

PROGRAM PROGRAM

PRESET

The actual camera position at the preset number pro- grammed in procedure 3 is learned as preset.

Preset data program

•Pan/Tilt (Joystick)

•Iris (Open/Close)

•Focus (Far/Near)

•Zoom (Tele/Wide)

Note: The preset data program differs depending on the camera. For further information, refer to the Operating Instructions for the camera to check the operations covered by the preset data program before operating the camera.

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Operating Instructions English Version Contents Preface FeaturesHandle the appliance with care PrecautionsDo not drop metallic parts through slots Do not attempt to disassemble the appliancePatrol Play/Patrol Learn Button Patrol Play Operate Indicator OperateAlarm Indicator Alarm Joystick Controller UP/DOWN/L/RWiper/Auxiliary 1 Button WIPER/AUX1 1Preset/Set/Program Preset Button4Alarm Reset/Suspend Button 5Camera Setup/Setup/Program Button0Data Selection Switch COAX/RS485 Alarm Input Terminal AlarmAlarm Output Terminal Alarm OUT Ground Terminal G Recover Input Terminal RecoverData Switch Setting SetupAlarm Switch Setting Connections DIP Switch SettingBasic System Connection System ConnectionData Connection with a Video SwitcherTerm Line Connection with a Time Lapse VCR Cable-loss Compensation SettingRS-485 Terminal Internal DiagramSetup Menu Alarm Setup Key Functions on the Setup MenuAlarm Output Setting Alarm Display SettingSite Alarm Setting Terminal Alarm SettingCable Compensation Setting System SetupSwitch Buzzer Setting Download Setting Preset Data Load SettingError Display Data Title Setting Upload SettingData Bit Setting Communication SettingUnit Address Setting Baud Rate SettingDelay Time Setting Parity Check SettingStop Bit Setting Wait Time SettingPan/Tilt Control Operating ProceduresLens Control Changing to Picture at Home Position Changing to Picture at Preset PositionOperation of Combination Camera Auto PanElectronic Shutter Camera Patrol FunctionCamera Functions Super DynamicElectronic Sensitivity Enhancement Automatic Gain ControlCamera Restart Defroster Control Camera Housing ControlExternal Device Control Wiper ControlAlarm Reset Alarm OperationAlarm Suspend Keys Used in Camera Setup Menu Camera SetupCamera SETUP/SETUP/PROGRAM button Camera Patrol Learning for Camera Patrol Operation Preset Position SettingMounting in the Rack InstallationALL Reset Specifications Panasonic Canada Inc Operating Instructions Précaution Version FrançaiseTable DES Matières Caractéristiques Dominantes PréraceNe jamais chercher à démonter lappareil Mesures DE PrécautionNe pas manipuler cet appareil brutalement Touche de dégivreur/dappareil auxiliaire 2 DEF/AUX2 Lampe-témoin de cas dalarme AlarmVue de la face avant Lampe-témoin dalimentation Operate2Touche de position de dé part/dé chappement HOME/ESC Touche dessuie-glace/dappareil auxiliaire 1 WIPER/AUX1Touches de ré glage de mise au point Focus NEAR/FAR 0Touches de pavé numé riqueVue de la face arriè re Ré glage du sé lecteur dalarme ConfigurationRé glage du commutateur de transmission de donné es Accè s à linterrupteur SW1 BranchementsBranchement de base Branchement DE Systè MERemarques Raccordement à un commutateur cyclique vidé oCâble RS-485 Câble coaxial Ré glage de compensation de pertes dans les câ bles Sché ma interne Borne RS-485Menu DE Configuration Configuration dalarme Fonctions attribuées aux touches Du menu de configurationAffichage du menu de configuration Ré glage de sortie dalarme Ré glage daffichage dalarmeRé glage dalarme de site Ré glage dalarme de borneRé glage de compensation de pertes dans les câ bles Configuration de systè meRé glage de sonnerie de commutateur Affichage derreur Ré glage de chargement de donné es pré sé lectionné esRé glage de titre de donné es Ré glage de té lé chargementRé glage de bit de transmission Ré glage de communicationRé glage dadresse dappareil Ré glage de vitesse de transmissionRé glage de temporisation Ré glage de contrô le de paritéRé glage de bit darrê t Ré glage de duré e dattenteProcé Dures Dutilisation Commande dobjectifBalayage panoramique automatique Utilisation dune camé ra vidé o de surveillance combiné eChangement des images de position pré sé lectionné e Changement des images à la position de dé partFonction Super Dynamic Fonction de patrouille de camé ra vidé o de surveillanceChangement dune image couleurà une image noir et blanc Fonctions de camé ra vidé o de surveillanceAccroissement de la sensibilité é lectronique Commande de gain automatiqueCommande de dé givreur Commande de compartiment de camé ra vidé oCommande dun appareil exté rieur Commande dessuie-glaceRemise à zé ro dalarme Dé clenchement dalarmeMise en non activité dalarme Touche Camera SETUP/SETUP/PROGRAM Configuration de camé ra vidé o de surveillanceLearning Ré glage de position pré sé lectionné ePanneau latéral Gauche Installation en bâ tiRemise À ZÉ RO GÉ NÉ Rale Caracté Ristiques Techniques Panasonic Canada Inc
Top Page Image Contents