Panasonic WV-CU161 operating instructions Setup, Data Switch Setting, Alarm Switch Setting

Page 9

SETUP

The WV-CU161 can be programmed by setting switches or from the interactive Setup menu as described below.

1.DIP Switch Setting (See page 10)

2.Data Switch Setting

For setting the mode of communication between the WV-CU161 and the combination camera.

3.Alarm Switch Setting

For setting up the alarm terminal. Turn off the power before setting this switch.

4.Setup of WV-CU161

Display the Setup menu (see page 17) to setup the WV-CU161.

■Data Switch Setting

Set this switch to specify the mode of communication between the WV-CU161 and a connected combination camera.

•Coaxial Multiplex communication via a coaxial cable

In this mode, control signals transmitted to the combi- nation camera are multiplexed with the video signals. Allows control of a camera installed at a distance of up to 900 m (3 000 ft) from the WV-CU161 via a single coaxial cable (When using RG-59U, BELDEN 9259 or equivalent cable).

•RS-485 site communication

In this mode, control signals transmitted to the combi- nation camera are separated into video signals and control signals.

Allows control of a camera installed at a distance 1 200 m (4 000 ft) or more from the WV-CU161 via an inter- face unit such as an AV Codec.

Note: Keep the power switch in the off position while setting each switch (DATA, TERM, LINE). The switch setting will not take effect if the power is on.

Rear Panel

RS485 DATA

T R TERM LNE

G B A B A ON 4 COAX

OFF 2 RS485

Coaxial Multiplex communication

RS-485 site communication

Set the 4 or 2 position according to the desired data line selection mode.

Set to ON position in case of terminating.

■Alarm Switch Setting

●For Using Alarm Input/Output Terminal and Alarm Recovery Input/Output Terminal

Place the Alarm Switch in the upper position for the following uses:

•Connection with the Time Lapse VCR.

•Transmitting the alarm signal to external devices.

•Resetting the alarm signal from external devices.

●For Using Alarm Input Terminals 1-4

Place the Alarm Switch in the lower position to use alarm input terminals 1-4.

This allows input of up to four alarm signals into the WV- CU161.

Also allows programming the alarm switch to activate four preset positions for a connected combination camera.

Note: Keep the power switch in the off position while setting the alarm switch. The switch setting will not take effect if the power is on.

For using alarm input/output terminal and alarm recovery input/output terminal

For using alarm input terminal 1-4

ALARM

ALARM IN

ALARM OUT

RECOVER IN

RESET OUT

4 3 G 2 1

ALARM IN

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Operating Instructions English Version Contents Preface FeaturesDo not drop metallic parts through slots PrecautionsDo not attempt to disassemble the appliance Handle the appliance with careAlarm Indicator Alarm Operate Indicator OperateJoystick Controller UP/DOWN/L/R Patrol Play/Patrol Learn Button Patrol Play4Alarm Reset/Suspend Button 1Preset/Set/Program Preset Button5Camera Setup/Setup/Program Button Wiper/Auxiliary 1 Button WIPER/AUX1Alarm Output Terminal Alarm OUT Alarm Input Terminal AlarmGround Terminal G Recover Input Terminal Recover 0Data Selection Switch COAX/RS485Setup Data Switch SettingAlarm Switch Setting Connections DIP Switch SettingBasic System Connection System ConnectionData Connection with a Video SwitcherTerm Line Connection with a Time Lapse VCR Cable-loss Compensation SettingRS-485 Terminal Internal DiagramSetup Menu Alarm Setup Key Functions on the Setup MenuSite Alarm Setting Alarm Display SettingTerminal Alarm Setting Alarm Output SettingSystem Setup Cable Compensation SettingSwitch Buzzer Setting Preset Data Load Setting Download SettingError Display Data Title Setting Upload SettingUnit Address Setting Communication SettingBaud Rate Setting Data Bit SettingStop Bit Setting Parity Check SettingWait Time Setting Delay Time SettingOperating Procedures Pan/Tilt ControlLens Control Operation of Combination Camera Changing to Picture at Preset PositionAuto Pan Changing to Picture at Home PositionCamera Functions Camera Patrol FunctionSuper Dynamic Electronic ShutterAutomatic Gain Control Electronic Sensitivity EnhancementCamera Restart External Device Control Camera Housing ControlWiper Control Defroster ControlAlarm Operation Alarm ResetAlarm Suspend Camera Setup Keys Used in Camera Setup MenuCamera SETUP/SETUP/PROGRAM button Camera Patrol Learning for Camera Patrol Operation Preset Position SettingMounting in the Rack InstallationALL Reset Specifications Panasonic Canada Inc Operating Instructions Précaution Version FrançaiseTable DES Matières Caractéristiques Dominantes PréraceMesures DE Précaution Ne jamais chercher à démonter lappareilNe pas manipuler cet appareil brutalement Vue de la face avant Lampe-témoin de cas dalarme AlarmLampe-témoin dalimentation Operate Touche de dégivreur/dappareil auxiliaire 2 DEF/AUX2Touches de ré glage de mise au point Focus NEAR/FAR Touche dessuie-glace/dappareil auxiliaire 1 WIPER/AUX10Touches de pavé numé rique 2Touche de position de dé part/dé chappement HOME/ESCVue de la face arriè re Configuration Ré glage du sé lecteur dalarmeRé glage du commutateur de transmission de donné es Accè s à linterrupteur SW1 BranchementsBranchement de base Branchement DE Systè MERemarques Raccordement à un commutateur cyclique vidé oCâble RS-485 Câble coaxial Ré glage de compensation de pertes dans les câ bles Sché ma interne Borne RS-485Menu DE Configuration Fonctions attribuées aux touches Du menu de configuration Configuration dalarmeAffichage du menu de configuration Ré glage dalarme de site Ré glage daffichage dalarmeRé glage dalarme de borne Ré glage de sortie dalarmeConfiguration de systè me Ré glage de compensation de pertes dans les câ blesRé glage de sonnerie de commutateur Affichage derreur Ré glage de chargement de donné es pré sé lectionné esRé glage de titre de donné es Ré glage de té lé chargementRé glage dadresse dappareil Ré glage de communicationRé glage de vitesse de transmission Ré glage de bit de transmissionRé glage de bit darrê t Ré glage de contrô le de paritéRé glage de duré e dattente Ré glage de temporisationProcé Dures Dutilisation Commande dobjectifChangement des images de position pré sé lectionné e Utilisation dune camé ra vidé o de surveillance combiné eChangement des images à la position de dé part Balayage panoramique automatiqueChangement dune image couleurà une image noir et blanc Fonction de patrouille de camé ra vidé o de surveillanceFonctions de camé ra vidé o de surveillance Fonction Super DynamicAccroissement de la sensibilité é lectronique Commande de gain automatiqueCommande dun appareil exté rieur Commande de compartiment de camé ra vidé oCommande dessuie-glace Commande de dé givreurDé clenchement dalarme Remise à zé ro dalarmeMise en non activité dalarme Touche Camera SETUP/SETUP/PROGRAM Configuration de camé ra vidé o de surveillanceLearning Ré glage de position pré sé lectionné ePanneau latéral Gauche Installation en bâ tiRemise À ZÉ RO GÉ NÉ Rale Caracté Ristiques Techniques Panasonic Canada Inc
Top Page Image Contents