Panasonic WV-CU161 Alarm Display Setting, Site Alarm Setting, Terminal Alarm Setting

Page 18

• For using alarm input terminals 1-4

ALARM SETUP

ALARM DISPLAY ON

SITE ALARM ON

TERM.ALARM ON

ALARM OUTPUT 10S

ALARM BUZZER ON

ALARM TERMINAL

(1) Alarm Display Setting

This item lets you select whether or not the message ALARM on the monitor when the alarm is activated.

1.Display the ALARM SETUP menu.

2.Select ALARM DISPLAY by moving the joystick up or down.

3.To have ALARM displayed, select ON for the ALARM DISPLAY parameter. Otherwise select OFF by moving the joystick to the right or left.

The initial factory setting is ON.

Note: The display time differs depending on (4) Alarm Output Setting.

(2) Site Alarm Setting

This item lets you enable or disable the camera site alarm.

1.Display the ALARM SETUP menu.

2.Select SITE ALARM by moving the joystick up or down.

3.Select SITE ALARM ON or OFF by moving the joystick to the right or left.

The initial factory setting is ON.

(3) Terminal Alarm Setting

This item lets you enable or disable the alarm signal from the alarm connector.

1.Display the ALARM SETUP menu.

2.Select TERM.ALARM by moving the joystick up or down.

3.Select TERM.ALARM ON or OFF by moving the joystick to the right or left.

The initial factory setting is ON.

(4) Alarm Output Setting

This item lets you select an alarm operation duration when the alarm is activated.

It determines the following. (The selected duration applies to each alarm operation.)

The length of time that ALARM is displayed on the mon- itor (ALARM DISPLAY ON mode).

The length of time the alarm is output to external devices (from the ALARM OUTPUT connector).

The length of time the buzzer sounds (ALARM BUZZER ON mode).

1.Display the ALARM SETUP menu.

2.Select ALARM OUTPUT by moving the joystick up or down.

3.Select the desired alarm output duration, 1S-30S, 40S 50S 1MIN 2MIN, 3MIN, 4MIN, 5MIN EXT, or OFF by moving the joystick to the right or left.

The initial factory setting is 10S.

EXT: The alarm signal continues to be output from the alarm output connector till the alarm is reset. The alarm is not automatically reset.

1S-5MIN:The alarm signal is supplied from the alarm output connector only for the set time. The alarm is automatically reset after the set time. (The ALARM indicator changes from blinking to steady light.)

OFF: No alarm output signal is supplied. (The alarm is deactivated.)

(5) Alarm Buzzer Setting

This item lets you select whether or not the alarm buzzer sounds when the alarm is activated.

1.Display the ALARM SETUP menu.

2.Select ALARM BUZZER by moving the joystick up or down.

3.Select ALARM BUZZER ON or OFF by moving the joy- stick to the right or left.

The initial factory setting is ON.

Note: The alarm buzzer time differs depending on (4) alarm output setting.

(6) Alarm Preset Setting

This item lets you select picture preset numbers in preset- ting combination camera positions when the alarm is acti- vated.

For using alarm input/output terminal and alarm recover input/output terminal.

ALARM SETUP

ALARM DISPLAY ON

SITE ALARM ON

TERM.ALARM ON

ALARM OUTPUT 10S

ALARM BUZZER ON

ALARM PRESET –

1.Display the ALARM SETUP menu.

2.Select ALARM PRESET by moving the joystick up or down.

3.Move the joystick to the right or left to select the desired preset numbers of the picture on the moni- tor in the range of 1-64 or [–] if no preset numbers are assigned.

The initial factory setting is – (No assignment).

1-64:Preset numbers

–:No assignment

Note: ALARM PRESET is available only when a combination camera is connected.

18

Image 18
Contents Operating Instructions English Version Contents Features PrefaceDo not attempt to disassemble the appliance PrecautionsDo not drop metallic parts through slots Handle the appliance with careJoystick Controller UP/DOWN/L/R Operate Indicator OperateAlarm Indicator Alarm Patrol Play/Patrol Learn Button Patrol Play5Camera Setup/Setup/Program Button 1Preset/Set/Program Preset Button4Alarm Reset/Suspend Button Wiper/Auxiliary 1 Button WIPER/AUX1Ground Terminal G Recover Input Terminal Recover Alarm Input Terminal AlarmAlarm Output Terminal Alarm OUT 0Data Selection Switch COAX/RS485Setup Data Switch SettingAlarm Switch Setting DIP Switch Setting ConnectionsSystem Connection Basic System ConnectionConnection with a Video Switcher DataTerm Line Cable-loss Compensation Setting Connection with a Time Lapse VCRInternal Diagram RS-485 TerminalSetup Menu Key Functions on the Setup Menu Alarm SetupTerminal Alarm Setting Alarm Display SettingSite Alarm Setting Alarm Output SettingSystem Setup Cable Compensation SettingSwitch Buzzer Setting Preset Data Load Setting Download SettingError Display Upload Setting Data Title SettingBaud Rate Setting Communication SettingUnit Address Setting Data Bit SettingWait Time Setting Parity Check SettingStop Bit Setting Delay Time SettingOperating Procedures Pan/Tilt ControlLens Control Auto Pan Changing to Picture at Preset PositionOperation of Combination Camera Changing to Picture at Home PositionSuper Dynamic Camera Patrol FunctionCamera Functions Electronic ShutterAutomatic Gain Control Electronic Sensitivity EnhancementCamera Restart Wiper Control Camera Housing ControlExternal Device Control Defroster ControlAlarm Operation Alarm ResetAlarm Suspend Camera Setup Keys Used in Camera Setup MenuCamera SETUP/SETUP/PROGRAM button Preset Position Setting Camera Patrol Learning for Camera Patrol OperationInstallation Mounting in the RackALL Reset Specifications Panasonic Canada Inc Operating Instructions Version Française PrécautionTable DES Matières Prérace Caractéristiques DominantesMesures DE Précaution Ne jamais chercher à démonter lappareilNe pas manipuler cet appareil brutalement Lampe-témoin dalimentation Operate Lampe-témoin de cas dalarme AlarmVue de la face avant Touche de dégivreur/dappareil auxiliaire 2 DEF/AUX20Touches de pavé numé rique Touche dessuie-glace/dappareil auxiliaire 1 WIPER/AUX1Touches de ré glage de mise au point Focus NEAR/FAR 2Touche de position de dé part/dé chappement HOME/ESCVue de la face arriè re Configuration Ré glage du sé lecteur dalarmeRé glage du commutateur de transmission de donné es Branchements Accè s à linterrupteur SW1Branchement DE Systè ME Branchement de baseRaccordement à un commutateur cyclique vidé o RemarquesCâble RS-485 Câble coaxial Ré glage de compensation de pertes dans les câ bles Borne RS-485 Sché ma interneMenu DE Configuration Fonctions attribuées aux touches Du menu de configuration Configuration dalarmeAffichage du menu de configuration Ré glage dalarme de borne Ré glage daffichage dalarmeRé glage dalarme de site Ré glage de sortie dalarmeConfiguration de systè me Ré glage de compensation de pertes dans les câ blesRé glage de sonnerie de commutateur Ré glage de chargement de donné es pré sé lectionné es Affichage derreurRé glage de té lé chargement Ré glage de titre de donné esRé glage de vitesse de transmission Ré glage de communicationRé glage dadresse dappareil Ré glage de bit de transmissionRé glage de duré e dattente Ré glage de contrô le de paritéRé glage de bit darrê t Ré glage de temporisationCommande dobjectif Procé Dures DutilisationChangement des images à la position de dé part Utilisation dune camé ra vidé o de surveillance combiné eChangement des images de position pré sé lectionné e Balayage panoramique automatiqueFonctions de camé ra vidé o de surveillance Fonction de patrouille de camé ra vidé o de surveillanceChangement dune image couleurà une image noir et blanc Fonction Super DynamicCommande de gain automatique Accroissement de la sensibilité é lectroniqueCommande dessuie-glace Commande de compartiment de camé ra vidé oCommande dun appareil exté rieur Commande de dé givreurDé clenchement dalarme Remise à zé ro dalarmeMise en non activité dalarme Configuration de camé ra vidé o de surveillance Touche Camera SETUP/SETUP/PROGRAMRé glage de position pré sé lectionné e LearningInstallation en bâ ti Panneau latéral GaucheRemise À ZÉ RO GÉ NÉ Rale Caracté Ristiques Techniques Panasonic Canada Inc