Texas Instruments TMS3320C5515 manual 2 I/O Memory Map, Overview

Page 20

Device Clocking

www.ti.com

pins for the load mode register command. During the mobile SDRAM initialization, the device issues the load mode register initialization command to two different addresses that differ in only the BA0 and BA1 address bits. These registers are the Extended Mode register and the Mode register. The extended mode register exists only in mSDRAM, and not in non-mSDRAM. If a non-mobile SDRAM memory ignores bits BA0 and BA1, the second loaded register value overwrites the first, leaving the desired value in the mode register and the non-mobile SDRAM works with the device.

Some timing parameters are programmable such as the refresh rate and CAS latencies. The EMIF supports up to 100 MHz SDCLK and has the ability to run the SDCLK at half the system clock to meet the EMIF I/O timing requirements and/or at lower power if a slower SDCLK can be used. Detailed information is available in the Clock Control section of the TMS320C5515/14/05/04 DSP External Memory Interface (EMIF) User's Guide (SPRUGU6).

1.2.2 I/O Memory Map

The C5x DSP has a separate memory map for peripheral and system registers, called I/O space. This space is 64K-words in length and is accessed via word read and write instructions dedicated for I/O space.

Separate documentation for I/O space registers related to each peripheral exists and is listed in the preface of this guide. System registers, which provide system-level control and status, are described in detail in other sections throughout this guide. Unused addresses in I/O space should be treated as reserved and should not be accessed. Accessing unused I/O space addresses may stall or hang the DSP.

Each of the four DMA controllers has access to a different set of peripherals and their I/O space registers. This is shown in Section 1.7.4.

NOTE: Writting to I/O space registers incurs in at least 2 CPU cycle latency. Thus, when configuring peripheral devices, wait at least two cycles before accessing data from the peripheral. When more than one peripheral register is updated in a sequence, the CPU only needs to wait following the final register write. For example, if the EMIF is being reconfigured, the CPU must wait until the very last EMIF register update takes effect before trying to access the external memory. The users should consult the respective peripheral user'sguide to determine if a peripheral requires additional initialization time.

Before accessing any peripheral register, make sure the peripheral is not held in reset and its internal clock is enabled. The peripheral reset control register (Section 1.7.5.2) and the peripheral clock gating control registers (Section 1.5.3.2.1) control these functions. Accessing a peripheral whose clocks are gated will either return the value of the last address read from the peripheral (when the clocks were last ON) or it may possibly hang the DSP -- depending on the peripheral.

1.3Device Clocking

1.3.1 Overview

The DSP requires two primary reference clocks: a system reference clock and a USB reference clock. The system clock, which is used by the CPU and most of the DSP peripherals, is controlled by the system clock generator. The system clock generator features a software-programmable PLL multiplier and several dividers. The system clock generator accepts an input reference clock from the CLKIN pin or the output clock of the 32.768-KHz real-time clock (RTC) oscillator. The selection of the input reference clock is based on the state of the CLK_SEL pin. The CLK_SEL pin is required to be statically tied high or low and cannot change dynamically after reset. The system clock generator can be used to modify the system reference clock signal according to software-programmable multiplier and dividers. The resulting clock output, the DSP system clock, is passed to the CPU, peripherals, and other modules inside the DSP. Alternatively, the system clock generator can be fully bypassed and the input reference clock can be passed directly to the DSP system clock. The USB reference clock is generated using a dedicated on-chip oscillator with a 12 MHz external crystal connected to the USB_MXI and USB_MXO pins. This crystal is not required if the USB peripheral is not being used. The USB oscillator cannot be used to provide the system reference clock.

The RTC oscillator generates a clock when a 32.768-KHz crystal is connected to the RTC_XI and

20

System Control

SPRUFX5A –October 2010 –Revised November 2010

 

 

Submit Documentation Feedback

Copyright © 2010, Texas Instruments Incorporated

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Users Guide Submit Documentation Feedback Contents List of Figures Submit Documentation Feedback List of Tables Submit Documentation Feedback Submit Documentation Feedback Read This First Related Documentation From Texas Instruments Related Documentation From Texas Instruments Submit Documentation Feedback Block Diagram Functional Block DiagramUsing FFT Accelerator ROM routines CPU CoreFFT Hardware Accelerator AddressPower Management PeripheralsSystem Memory Program/Data Memory MapOn-Chip Dual-Access RAM Daram Daram BlocksCPU Byte Address Range DaramSaram On-Chip Single-Access RAM SaramSaram Blocks On-Chip Single-Access Read-Only Memory Sarom Sarom BlocksExternal Memory Asynchronous Emif Interface2 I/O Memory Map OverviewDevice Clocking DSP Clocking Diagram Clock Domains PLL Output Frequency Configuration Powering Down and Powering Up the System PLLFunctional Description Multiplier and DividersBit Field Value Description Clkout PinSRC Configuration DSP Reset Conditions of the System Clock GeneratorClock Generator During Reset Clock Generator After ResetRegister Bits Used in the Bypass Mode Setting the System Clock Frequency In the Bypass ModeEntering and Exiting the PLL Mode Register Bits Used in the PLL ModeSetting the Output Frequency for the PLL Mode CV DD = 1.05 CV DD = 1.3 Clock Signal NameFrequency Ranges for Internal Clocks 10. PLL Clock Frequency RangesClock Generator Registers Lock TimeSoftware Steps To Modify Multiplier and Divider Ratios 12. Clock Generator RegistersClock Generator Control Register 1 CGCR1 1C20h Clock Generator Control Register 2 CGCR2 1C21hInit Clock Generator Control Register 3 CGCR3 1C22hClock Generator Control Register 4 CGCR4 1C23h Clock Configuration Register 1 CCR1 1C1Eh 17. Clock Configuration Register 1 CCR1 Field DescriptionsClock Configuration Register 2 CCR2 1C1Fh 18. Clock Configuration Register 2 CCR2 Field DescriptionsPower Domains 19. Power Management FeaturesClock Management 20. DSP Power DomainsPower Domains Description CPU Domain Clock Gating DaramHwai 21. Idle Configuration Register ICR Field DescriptionsHwai Iporti Mporti Xporti Dporti Idlecfg Cpui 23. CPU Clock Domain Idle Requirements Valid Idle Configurations22. Idle Status Register Istr Field Descriptions Clock Configuration Process Peripheral Domain Clock GatingTo Idle the Following Module/Port XportMMCSD0CG DMA0CG Uartcg Spicg I2S3CG SysclkdisMMCSD0CG Anaregcg DMA3CG DMA2CG DMA1CG Usbcg Sarcg Lcdcg AnaregcgUrtclkstpack UrtclkstpreqUsbclkstpack UsbclkstpreqClock Generator Domain Clock Gating USB Domain Clock GatingBit Field EmfclkstpackUSB System Control Register Usbscr 1C32h 27. USB System Control Register Usbscr Field DescriptionsUsbpwdn Usbsessend Usbvbusdet Usbpllen UsbpwdnRTC Domain Clock Gating UsbdatpolUsboscbiasdis UsboscdisStatic Power Management RTC Power Management Register Rtcpmgt 1930hRTC Interrupt Flag Register Rtcintfl 1920h 29. RTC Interrupt Flag Register Rtcintfl Field DescriptionsInternal Memory Low Power Modes RAM Sleep Mode Control Register 1 RAMSLPMDCNTLR1 1C28hMode CV DD Voltage 30. On-Chip Memory Standby Modes21. RAM Sleep Mode Control Register2 0x1C2A Power Configurations 31. Power ConfigurationsDV DDRTC, Ldoi IDLE3IDLE2 Procedure IDLE3 Procedure Core Voltage Scaling32. Interrupt Table HEX BytesIFR and IER Registers 33. IFR0 and IER0 Bit DescriptionsInterrupt Timing 34. IFR1 and IER1 Bit DescriptionsRtos Dlog Berr I2C Emif Gpio USB SPI RTC RCV3 XMT3 RtosDMA Interrupt Enable and Aggregation Flag Registers Timer Interrupt Aggregation Flag Register Tiafr 1C14hGpio Interrupt Enable and Aggregation Flag Registers Device Identification 35. Die ID RegistersDie ID Register 0 DIEIDR0 1C40h 36. Die ID Register 0 DIEIDR0 Field DescriptionsDie ID Register 1 DIEIDR1 1C41h 37. Die ID Register 1 DIEIDR1 Field DescriptionsDie ID Register 3 DIEIDR3150 1C43h 39. Die ID Register 3 DIEIDR3150 Field DescriptionsDie ID Register 4 DIEIDR4 1C44h 40. Die ID Register 4 DIEIDR4 Field DescriptionsDie ID Register 6 DIEIDR6 1C46h 42. Die ID Register 6 DIEIDR6 Field DescriptionsDie ID Register 7 DIEIDR7 1C47h 43. Die ID Register 7 DIEIDR7 Field DescriptionsDevice Configuration External Bus Selection Register Ebsr44. Ebsr Register Bit Descriptions Field Descriptions LDO Control Register 7004h LDO ControlA17MODE A16MODE45. Rtcpmgt Register Bit Descriptions Field Descriptions 46. Ldocntl Register Bit Descriptions Field Descriptions 47. LDO Controls MatrixRtcpmgt Register Ldocntl Register Bgpd Bit Ldopd Bit Usbldoen BitEmifsr Output Slew Rate Control Register Osrcr 1C16hClkoutsr S15PD S14PD S13PD S12PD S11PD S10PD S05PD S04PD S03PD S02PD S01PD S00PDS15PD S05PDINT1PU INT1PU INT0PU Resetpu EMU01PU Tdipu Tmspu TckpuA20PD A19PD A18PD A17PD A16PD A15PD A20PD PD15PDDMA Controller Configuration DMA Configuration Registers DMA Synchronization Events52. Channel Synchronization Events for DMA Controllers 53. System Registers Related to the DMA Controllers55. DMA Interrupt Enable Register Dmaier Field Descriptions 54. DMA Interrupt Flag Register Dmaifr Field DescriptionsPeripheral Reset CH1EVTCH0EVT CH3EVTPeripheral Software Reset Counter Register Psrcr 1C04h Peripheral Reset Control Register Prcr 1C05hCount PG4RSTEmif and USB Byte Access PG3RST60. Effect of Bytemode Bits on Emif Accesses 61. Effect of Usbscr Bytemode Bits on USB AccessBytemode Setting CPU Access to USB Register Emif System Control Register Escr 1C33hEdiv Emif Clock Divider Register Ecdr 1C26h63. Emif Clock Divider Register Ecdr Field Descriptions Rfid Products ApplicationsDSP

TMS3320C5515 specifications

The Texas Instruments TMS3320C5515 is a highly specialized digital signal processor (DSP) designed for a wide range of applications, including telecommunications, audio processing, and other signal-intensive tasks. As part of the TMS320 family of DSPs, the TMS3320C5515 leverages TI's extensive experience in signal processing technology, delivering robust performance and reliability.

One of the main features of the TMS3320C5515 is its 32-bit architecture, which allows for a high level of precision in digital signal computation. The processor is capable of executing complex mathematical algorithms, making it suitable for tasks that require high-speed data processing, such as speech recognition and audio filtering. With a native instruction set optimized for DSP applications, the TMS3320C5515 can perform multiply-accumulate operations in a single cycle, significantly enhancing computational efficiency.

The TMS3320C5515 employs advanced technologies including a Harvard architecture that separates instruction and data memory, enabling simultaneous access and improving performance. Its dual data buses enhance throughput by allowing multi-channel processing, making it particularly effective for real-time applications where timely data manipulation is critical. The device supports a wide range of peripherals, facilitating connections to various sensors and communication systems, which is vital in embedded applications.

In terms of characteristics, the TMS3320C5515 operates at an impressive clock speed, providing the computational power necessary to handle demanding tasks. The device is optimized for low power consumption, making it ideal for battery-operated applications without sacrificing performance. Its flexibility in processing algorithms also allows it to be readily adapted for specific requirements, from audio codecs to modems.

Another noteworthy aspect is the extensive development ecosystem surrounding the TMS3320C5515, which includes software tools, libraries, and support resources designed to accelerate the development process. This allows engineers and developers to bring their projects to market more quickly while minimizing risk.

Overall, the Texas Instruments TMS3320C5515 stands out as a powerful DSP solution, equipped with features that cater to the needs of various industries. Its combination of performance, efficiency, and versatile application makes it an attractive choice for engineers working in signal processing.
Top Page Image Contents