Texas Instruments TMS3320C5515 manual CPU Domain Clock Gating, Daram

Page 35

www.ti.com

Power Management

There are two distinct methods of clock gating. The first uses the ICR CPU register and the CPU'sIDLE instruction. This method is used for the following domains: CPU, IPORT, DPORT, MPORT, XPORT & HWA. See Figure 1-3for a diagram of these domains. In this method, the ICR is written with a value indicating the desired clock gating configuration and then (possibly much later) the IDLE instruction is executed. The contents of the ICR do not become effective until the IDLE instruction is executed. The second method uses system registers, PCGCR1 & PCGCR2. These registers control most of the peripheral clock domains and writes to this register take effect immediately.

The SYSCLKDIS bit in PCGCR register has global effect and, therefore, is a superset of the two methods. When this bit as asserted the whole device is clock gated with the exceptions of the PLL, the USB PLL, the RTC, and the oscillators.

NOTE: Stopping clocks to a domain or a module within that domain only affects active power consumption; it does not affect leakage power consumption.

NOTE: The on-chip Bootloader idles all peripherals and CPU ports at startup, but it enables some peripherals as it uses them. Application code should not assume all peripherals and CPU ports are disabled. To get the minimum power consumption, make sure to disable all peripherals and CPU ports first and then enable only necessary peripherals and CPU ports before using them.

1.5.3.1CPU Domain Clock Gating

Two registers are provided to individually configure and monitor the clock gating modes of the CPU domain: the idle configuration register (ICR) and the idle status register (ISTR).

ICR lets you configure how the CPU domain will respond the next time the idle instruction is executed. When you execute the idle instruction, the content of ICR is copied to ISTR. Then the ISTR values are propagated to the different portions of the CPU domain.

In the CPU domain, there are five CPU ports.

•IPORT: this port is used by the CPU for fetching instructions from external memory.

•DPORT: this port is used by the CPU when reading and writing data from/to external memory.

•XPORT: this port is used by the CPU when reading and writing from/to IO-space (peripheral) registers.

•MPORT: this port is used by the four DMAs, the USB'sCDMA, and the LCD controller'sDMA when accessing SARAM or DARAM.

•MPORT: this port is used by the four DMAs and the USB'sCDMA when accessing SARAM or

DARAM.

•HWA: this port is the hardware accelerator (FFT coprocessor). It shares all CPU buses.

SPRUFX5A –October 2010 –Revised November 2010

System Control

35

Submit Documentation Feedback

 

 

Copyright © 2010, Texas Instruments Incorporated

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Users Guide Submit Documentation Feedback Contents List of Figures Submit Documentation Feedback List of Tables Submit Documentation Feedback Submit Documentation Feedback Read This First Related Documentation From Texas Instruments Related Documentation From Texas Instruments Submit Documentation Feedback Functional Block Diagram Block DiagramAddress Using FFT Accelerator ROM routinesCPU Core FFT Hardware AcceleratorPeripherals Power ManagementProgram/Data Memory Map System MemoryDaram On-Chip Dual-Access RAM DaramDaram Blocks CPU Byte Address RangeSaram On-Chip Single-Access RAM SaramSaram Blocks Asynchronous Emif Interface On-Chip Single-Access Read-Only Memory SaromSarom Blocks External MemoryOverview 2 I/O Memory MapDevice Clocking DSP Clocking Diagram Clock Domains Multiplier and Dividers PLL Output Frequency ConfigurationPowering Down and Powering Up the System PLL Functional DescriptionBit Field Value Description Clkout PinSRC Clock Generator After Reset ConfigurationDSP Reset Conditions of the System Clock Generator Clock Generator During ResetRegister Bits Used in the PLL Mode Register Bits Used in the Bypass ModeSetting the System Clock Frequency In the Bypass Mode Entering and Exiting the PLL Mode10. PLL Clock Frequency Ranges Setting the Output Frequency for the PLL ModeCV DD = 1.05 CV DD = 1.3 Clock Signal Name Frequency Ranges for Internal Clocks12. Clock Generator Registers Clock Generator RegistersLock Time Software Steps To Modify Multiplier and Divider RatiosClock Generator Control Register 2 CGCR2 1C21h Clock Generator Control Register 1 CGCR1 1C20hInit Clock Generator Control Register 3 CGCR3 1C22hClock Generator Control Register 4 CGCR4 1C23h 18. Clock Configuration Register 2 CCR2 Field Descriptions Clock Configuration Register 1 CCR1 1C1Eh17. Clock Configuration Register 1 CCR1 Field Descriptions Clock Configuration Register 2 CCR2 1C1Fh19. Power Management Features Power DomainsClock Management 20. DSP Power DomainsPower Domains Description Daram CPU Domain Clock GatingHwai 21. Idle Configuration Register ICR Field DescriptionsHwai Iporti Mporti Xporti Dporti Idlecfg Cpui 23. CPU Clock Domain Idle Requirements Valid Idle Configurations22. Idle Status Register Istr Field Descriptions Xport Clock Configuration ProcessPeripheral Domain Clock Gating To Idle the Following Module/PortSysclkdis MMCSD0CG DMA0CG Uartcg Spicg I2S3CGMMCSD0CG Anaregcg Anaregcg DMA3CG DMA2CG DMA1CG Usbcg Sarcg LcdcgUsbclkstpreq UrtclkstpackUrtclkstpreq UsbclkstpackEmfclkstpack Clock Generator Domain Clock GatingUSB Domain Clock Gating Bit FieldUsbpwdn USB System Control Register Usbscr 1C32h27. USB System Control Register Usbscr Field Descriptions Usbpwdn Usbsessend Usbvbusdet UsbpllenUsboscdis RTC Domain Clock GatingUsbdatpol UsboscbiasdisRTC Power Management Register Rtcpmgt 1930h Static Power Management29. RTC Interrupt Flag Register Rtcintfl Field Descriptions RTC Interrupt Flag Register Rtcintfl 1920h30. On-Chip Memory Standby Modes Internal Memory Low Power ModesRAM Sleep Mode Control Register 1 RAMSLPMDCNTLR1 1C28h Mode CV DD Voltage21. RAM Sleep Mode Control Register2 0x1C2A IDLE3 Power Configurations31. Power Configurations DV DDRTC, LdoiIDLE2 Procedure Core Voltage Scaling IDLE3 ProcedureHEX Bytes 32. Interrupt Table33. IFR0 and IER0 Bit Descriptions IFR and IER RegistersRtos Interrupt Timing34. IFR1 and IER1 Bit Descriptions Rtos Dlog Berr I2C Emif Gpio USB SPI RTC RCV3 XMT3DMA Interrupt Enable and Aggregation Flag Registers Timer Interrupt Aggregation Flag Register Tiafr 1C14hGpio Interrupt Enable and Aggregation Flag Registers 35. Die ID Registers Device Identification37. Die ID Register 1 DIEIDR1 Field Descriptions Die ID Register 0 DIEIDR0 1C40h36. Die ID Register 0 DIEIDR0 Field Descriptions Die ID Register 1 DIEIDR1 1C41h40. Die ID Register 4 DIEIDR4 Field Descriptions Die ID Register 3 DIEIDR3150 1C43h39. Die ID Register 3 DIEIDR3150 Field Descriptions Die ID Register 4 DIEIDR4 1C44h43. Die ID Register 7 DIEIDR7 Field Descriptions Die ID Register 6 DIEIDR6 1C46h42. Die ID Register 6 DIEIDR6 Field Descriptions Die ID Register 7 DIEIDR7 1C47hExternal Bus Selection Register Ebsr Device Configuration44. Ebsr Register Bit Descriptions Field Descriptions A16MODE LDO Control Register 7004hLDO Control A17MODE45. Rtcpmgt Register Bit Descriptions Field Descriptions Bgpd Bit Ldopd Bit Usbldoen Bit 46. Ldocntl Register Bit Descriptions Field Descriptions47. LDO Controls Matrix Rtcpmgt Register Ldocntl RegisterEmifsr Output Slew Rate Control Register Osrcr 1C16hClkoutsr S05PD S15PD S14PD S13PD S12PD S11PD S10PDS05PD S04PD S03PD S02PD S01PD S00PD S15PDINT1PU INT1PU INT0PU Resetpu EMU01PU Tdipu Tmspu TckpuA20PD A19PD A18PD A17PD A16PD A15PD PD15PD A20PDDMA Controller Configuration 53. System Registers Related to the DMA Controllers DMA Configuration RegistersDMA Synchronization Events 52. Channel Synchronization Events for DMA Controllers54. DMA Interrupt Flag Register Dmaifr Field Descriptions 55. DMA Interrupt Enable Register Dmaier Field DescriptionsCH3EVT Peripheral ResetCH1EVT CH0EVTPG4RST Peripheral Software Reset Counter Register Psrcr 1C04hPeripheral Reset Control Register Prcr 1C05h CountPG3RST Emif and USB Byte AccessEmif System Control Register Escr 1C33h 60. Effect of Bytemode Bits on Emif Accesses61. Effect of Usbscr Bytemode Bits on USB Access Bytemode Setting CPU Access to USB RegisterEdiv Emif Clock Divider Register Ecdr 1C26h63. Emif Clock Divider Register Ecdr Field Descriptions Rfid Products ApplicationsDSP

TMS3320C5515 specifications

The Texas Instruments TMS3320C5515 is a highly specialized digital signal processor (DSP) designed for a wide range of applications, including telecommunications, audio processing, and other signal-intensive tasks. As part of the TMS320 family of DSPs, the TMS3320C5515 leverages TI's extensive experience in signal processing technology, delivering robust performance and reliability.

One of the main features of the TMS3320C5515 is its 32-bit architecture, which allows for a high level of precision in digital signal computation. The processor is capable of executing complex mathematical algorithms, making it suitable for tasks that require high-speed data processing, such as speech recognition and audio filtering. With a native instruction set optimized for DSP applications, the TMS3320C5515 can perform multiply-accumulate operations in a single cycle, significantly enhancing computational efficiency.

The TMS3320C5515 employs advanced technologies including a Harvard architecture that separates instruction and data memory, enabling simultaneous access and improving performance. Its dual data buses enhance throughput by allowing multi-channel processing, making it particularly effective for real-time applications where timely data manipulation is critical. The device supports a wide range of peripherals, facilitating connections to various sensors and communication systems, which is vital in embedded applications.

In terms of characteristics, the TMS3320C5515 operates at an impressive clock speed, providing the computational power necessary to handle demanding tasks. The device is optimized for low power consumption, making it ideal for battery-operated applications without sacrificing performance. Its flexibility in processing algorithms also allows it to be readily adapted for specific requirements, from audio codecs to modems.

Another noteworthy aspect is the extensive development ecosystem surrounding the TMS3320C5515, which includes software tools, libraries, and support resources designed to accelerate the development process. This allows engineers and developers to bring their projects to market more quickly while minimizing risk.

Overall, the Texas Instruments TMS3320C5515 stands out as a powerful DSP solution, equipped with features that cater to the needs of various industries. Its combination of performance, efficiency, and versatile application makes it an attractive choice for engineers working in signal processing.
Top Page Image Contents