Texas Instruments TMS3320C5515 Output Slew Rate Control Register Osrcr 1C16h, Clkoutsr, Emifsr

Page 66

System Configuration and Control

www.ti.com

1.7.3.4Output Slew Rate Control Register (OSRCR) [1C16h]

To provide the lowest power consumption setting, the DSP has configurable slew rate control on the EMIF and CLKOUT output pins. The output slew rate control register (OSRCR) is used to set a subset of the device I/O pins, namely CLKOUT and EMIF pins, to either fast or slow slew rate. The slew rate feature is implemented by staging/delaying turn-on times of the parallel p-channel drive transistors and parallel n-channel drive transistors of the output buffer. In the slow slew rate configuration, the delay is longer, but ultimately the same number of parallel transistors are used to drive the output high or low; therefore, the drive strength is ultimately the same. The slower slew rate control can be used for power savings and has the greatest effect at lower DVDDIO and DVDDEMIF voltages.

The output slew rate control register (OSRCR) is shown in Figure 1-38and described in Table 1-48.

Figure 1-38. Output Slew Rate Control Register (OSRCR) [1C16h]

15

3

2

1

0

Reserved

 

CLKOUTSR

Reserved

EMIFSR

R-0

 

RW-1

R-0

RW-1

LEGEND: R/W = Read/Write; R = Read only; -n= value after reset

Table 1-48. Output Slew Rate Control Register (OSRCR) Field Descriptions

Bit

Field

Value

Description

 

 

 

 

15-3

Reserved

0

Reserved.

 

 

 

 

2

CLKOUTSR

 

CLKOUT pin output slew rate bits. These bits set the slew rate for the CLKOUT pin.

 

 

0

Slow slew rate

 

 

1

Fast slew rate

 

 

 

 

1

Reserved

0

Reserved.

 

 

 

 

0

EMIFSR

 

EMIF pin output slew rate bits. These bits set the slew rate for the EMIF pins.

 

 

0

Slow slew rate

 

 

1

Fast slew rate

 

 

 

 

66

System Control

SPRUFX5A –October 2010 –Revised November 2010

 

 

Submit Documentation Feedback

Copyright © 2010, Texas Instruments Incorporated

Page 65 Page 67
Image 66
Page 65 Page 67
Contents Users Guide Submit Documentation Feedback Contents List of Figures Submit Documentation Feedback List of Tables Submit Documentation Feedback Submit Documentation Feedback Read This First Related Documentation From Texas Instruments Related Documentation From Texas Instruments Submit Documentation Feedback Block Diagram Functional Block DiagramFFT Hardware Accelerator Using FFT Accelerator ROM routinesCPU Core AddressPower Management PeripheralsSystem Memory Program/Data Memory MapCPU Byte Address Range On-Chip Dual-Access RAM DaramDaram Blocks DaramOn-Chip Single-Access RAM Saram Saram BlocksSaram External Memory On-Chip Single-Access Read-Only Memory SaromSarom Blocks Asynchronous Emif Interface2 I/O Memory Map OverviewDevice Clocking DSP Clocking Diagram Clock Domains Functional Description PLL Output Frequency ConfigurationPowering Down and Powering Up the System PLL Multiplier and DividersClkout Pin SRCBit Field Value Description Clock Generator During Reset ConfigurationDSP Reset Conditions of the System Clock Generator Clock Generator After ResetEntering and Exiting the PLL Mode Register Bits Used in the Bypass ModeSetting the System Clock Frequency In the Bypass Mode Register Bits Used in the PLL ModeFrequency Ranges for Internal Clocks Setting the Output Frequency for the PLL ModeCV DD = 1.05 CV DD = 1.3 Clock Signal Name 10. PLL Clock Frequency RangesSoftware Steps To Modify Multiplier and Divider Ratios Clock Generator RegistersLock Time 12. Clock Generator RegistersClock Generator Control Register 1 CGCR1 1C20h Clock Generator Control Register 2 CGCR2 1C21hClock Generator Control Register 3 CGCR3 1C22h Clock Generator Control Register 4 CGCR4 1C23hInit Clock Configuration Register 2 CCR2 1C1Fh Clock Configuration Register 1 CCR1 1C1Eh17. Clock Configuration Register 1 CCR1 Field Descriptions 18. Clock Configuration Register 2 CCR2 Field DescriptionsPower Domains 19. Power Management Features20. DSP Power Domains Power Domains DescriptionClock Management CPU Domain Clock Gating Daram21. Idle Configuration Register ICR Field Descriptions Hwai Iporti Mporti Xporti Dporti Idlecfg CpuiHwai Valid Idle Configurations 22. Idle Status Register Istr Field Descriptions23. CPU Clock Domain Idle Requirements To Idle the Following Module/Port Clock Configuration ProcessPeripheral Domain Clock Gating XportMMCSD0CG DMA0CG Uartcg Spicg I2S3CG SysclkdisMMCSD0CG Anaregcg DMA3CG DMA2CG DMA1CG Usbcg Sarcg Lcdcg AnaregcgUsbclkstpack UrtclkstpackUrtclkstpreq UsbclkstpreqBit Field Clock Generator Domain Clock GatingUSB Domain Clock Gating EmfclkstpackUsbpwdn Usbsessend Usbvbusdet Usbpllen USB System Control Register Usbscr 1C32h27. USB System Control Register Usbscr Field Descriptions UsbpwdnUsboscbiasdis RTC Domain Clock GatingUsbdatpol UsboscdisStatic Power Management RTC Power Management Register Rtcpmgt 1930hRTC Interrupt Flag Register Rtcintfl 1920h 29. RTC Interrupt Flag Register Rtcintfl Field DescriptionsMode CV DD Voltage Internal Memory Low Power ModesRAM Sleep Mode Control Register 1 RAMSLPMDCNTLR1 1C28h 30. On-Chip Memory Standby Modes21. RAM Sleep Mode Control Register2 0x1C2A DV DDRTC, Ldoi Power Configurations31. Power Configurations IDLE3IDLE2 Procedure IDLE3 Procedure Core Voltage Scaling32. Interrupt Table HEX BytesIFR and IER Registers 33. IFR0 and IER0 Bit DescriptionsRtos Dlog Berr I2C Emif Gpio USB SPI RTC RCV3 XMT3 Interrupt Timing34. IFR1 and IER1 Bit Descriptions RtosTimer Interrupt Aggregation Flag Register Tiafr 1C14h Gpio Interrupt Enable and Aggregation Flag RegistersDMA Interrupt Enable and Aggregation Flag Registers Device Identification 35. Die ID RegistersDie ID Register 1 DIEIDR1 1C41h Die ID Register 0 DIEIDR0 1C40h36. Die ID Register 0 DIEIDR0 Field Descriptions 37. Die ID Register 1 DIEIDR1 Field DescriptionsDie ID Register 4 DIEIDR4 1C44h Die ID Register 3 DIEIDR3150 1C43h39. Die ID Register 3 DIEIDR3150 Field Descriptions 40. Die ID Register 4 DIEIDR4 Field DescriptionsDie ID Register 7 DIEIDR7 1C47h Die ID Register 6 DIEIDR6 1C46h42. Die ID Register 6 DIEIDR6 Field Descriptions 43. Die ID Register 7 DIEIDR7 Field DescriptionsDevice Configuration External Bus Selection Register Ebsr44. Ebsr Register Bit Descriptions Field Descriptions A17MODE LDO Control Register 7004hLDO Control A16MODE45. Rtcpmgt Register Bit Descriptions Field Descriptions Rtcpmgt Register Ldocntl Register 46. Ldocntl Register Bit Descriptions Field Descriptions47. LDO Controls Matrix Bgpd Bit Ldopd Bit Usbldoen BitOutput Slew Rate Control Register Osrcr 1C16h ClkoutsrEmifsr S15PD S15PD S14PD S13PD S12PD S11PD S10PDS05PD S04PD S03PD S02PD S01PD S00PD S05PDINT1PU INT0PU Resetpu EMU01PU Tdipu Tmspu Tckpu A20PD A19PD A18PD A17PD A16PD A15PDINT1PU A20PD PD15PDDMA Controller Configuration 52. Channel Synchronization Events for DMA Controllers DMA Configuration RegistersDMA Synchronization Events 53. System Registers Related to the DMA Controllers55. DMA Interrupt Enable Register Dmaier Field Descriptions 54. DMA Interrupt Flag Register Dmaifr Field DescriptionsCH0EVT Peripheral ResetCH1EVT CH3EVTCount Peripheral Software Reset Counter Register Psrcr 1C04hPeripheral Reset Control Register Prcr 1C05h PG4RSTEmif and USB Byte Access PG3RSTBytemode Setting CPU Access to USB Register 60. Effect of Bytemode Bits on Emif Accesses61. Effect of Usbscr Bytemode Bits on USB Access Emif System Control Register Escr 1C33hEmif Clock Divider Register Ecdr 1C26h 63. Emif Clock Divider Register Ecdr Field DescriptionsEdiv Products Applications DSPRfid

TMS3320C5515 specifications

The Texas Instruments TMS3320C5515 is a highly specialized digital signal processor (DSP) designed for a wide range of applications, including telecommunications, audio processing, and other signal-intensive tasks. As part of the TMS320 family of DSPs, the TMS3320C5515 leverages TI's extensive experience in signal processing technology, delivering robust performance and reliability.

One of the main features of the TMS3320C5515 is its 32-bit architecture, which allows for a high level of precision in digital signal computation. The processor is capable of executing complex mathematical algorithms, making it suitable for tasks that require high-speed data processing, such as speech recognition and audio filtering. With a native instruction set optimized for DSP applications, the TMS3320C5515 can perform multiply-accumulate operations in a single cycle, significantly enhancing computational efficiency.

The TMS3320C5515 employs advanced technologies including a Harvard architecture that separates instruction and data memory, enabling simultaneous access and improving performance. Its dual data buses enhance throughput by allowing multi-channel processing, making it particularly effective for real-time applications where timely data manipulation is critical. The device supports a wide range of peripherals, facilitating connections to various sensors and communication systems, which is vital in embedded applications.

In terms of characteristics, the TMS3320C5515 operates at an impressive clock speed, providing the computational power necessary to handle demanding tasks. The device is optimized for low power consumption, making it ideal for battery-operated applications without sacrificing performance. Its flexibility in processing algorithms also allows it to be readily adapted for specific requirements, from audio codecs to modems.

Another noteworthy aspect is the extensive development ecosystem surrounding the TMS3320C5515, which includes software tools, libraries, and support resources designed to accelerate the development process. This allows engineers and developers to bring their projects to market more quickly while minimizing risk.

Overall, the Texas Instruments TMS3320C5515 stands out as a powerful DSP solution, equipped with features that cater to the needs of various industries. Its combination of performance, efficiency, and versatile application makes it an attractive choice for engineers working in signal processing.
Top Page Image Contents