Texas Instruments TMS3320C5515 manual Urtclkstpack, Urtclkstpreq, Usbclkstpack, Usbclkstpreq

Page 42

Power Management

www.ti.com

1.5.3.2.2 Peripheral Clock Stop Request/Acknowledge Register (CLKSTOP) [1C3Ah]

You must execute a handshaking procedure before stopping the clock to the EMIF, USB, and UART. This handshake procedure ensures that current bus transactions are completed before the clock is stopped. The peripheral clock stop request/acknowledge register (CLKSTOP) enables this handshaking mechanism.

To stop the clock to the EMIF, USB, or UART, set the corresponding clock stop request bit in the CLKSTOP register, then wait for the peripheral to set the corresponding clock stop acknowledge bit. Once this bit is set, you can idle the corresponding clock in the PCGCR1 and PCGCR2.

To enable the clock to the EMIF, USB, or UART, first enable the clock the peripheral through PCGCR1 or PCGCR2, then clear the corresponding clock stop request bit in the CLKSTOP register.

The peripheral clock stop request/acknowledge register (CLKSTOP) is shown in Figure 1-16and described in Table 1-26.

Figure 1-16. Peripheral Clock Stop Request/Acknowledge Register (CLKSTOP) [1C3Ah]

15

 

 

 

 

 

 

8

 

 

 

 

Reserved

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

R-0

 

 

 

7

6

5

4

3

2

1

0

Reserved

URTCLKSTPACK URTCLKSTPREQ USBCLKSTPACK USBCLKSTPREQ EMFCLKSTPACK EMFCLKSTPREQ

R-0

R-1

R/W-1

R-1

R/W-1

R-1

R/W-1

LEGEND: R/W = Read/Write; R = Read only;

-n= value after reset

 

 

 

 

Table 1-26. Peripheral Clock Stop Request/Acknowledge Register (CLKSTOP) Field Descriptions

Bit

Field

Value

Description

 

 

 

 

15-6

Reserved

0

Reserved.

 

 

 

 

5

URTCLKSTPACK

 

UART clock stop acknowledge bit. This bit is set to 1 when the UART has acknowledged

 

 

 

a request for its clock to be stopped. The UART clock should not be stopped until this bit

 

 

 

is set to 1.

 

 

0

The request to stop the peripheral clock has not been acknowledged.

 

 

1

The request to stop the peripheral clock has been acknowledged, the clock can be

 

 

 

stopped.

 

 

 

 

4

URTCLKSTPREQ

 

UART peripheral clock stop request bit. When disabling the UART internal peripheral

 

 

 

clock, you must set this bit to 1 to request permission to stop the clock. After the UART

 

 

 

acknowledges the request (URTCLKSTPACK = 1) you can stop the clock through the

 

 

 

peripheral clock gating control register 1 (PCGCR1). When enabling the UART internal

 

 

 

clock, enable the clock through PCGCR1, then set URTCKLSTPREQ to 0.

 

 

0

Normal operating mode.

 

 

1

Request permission to stop the peripheral clock.

 

 

 

 

3

USBCLKSTPACK

 

USB clock stop acknowledge bit. This bit is set to 1 when the USB has acknowledged a

 

 

 

request for its clock to be stopped. The USB clock should not be stopped until this bit is

 

 

 

set to 1.

 

 

0

The request to stop the peripheral clock has not been acknowledged.

 

 

1

The request to stop the peripheral clock has been acknowledged, the clock can be

 

 

 

stopped.

 

 

 

 

2

USBCLKSTPREQ

 

USB peripheral clock stop request bit. When disabling the USB internal peripheral clock,

 

 

 

you must set this bit to 1 to request permission to stop the clock. After the USB

 

 

 

acknowledges the request (USBCLKSTPACK = 1) you can stop the clock through the

 

 

 

peripheral clock gating control register 2 (PCGCR2). When enabling the USB internal

 

 

 

clock, enable the clock through PCGCR2, then set USBCKLSTPREQ to 0.

 

 

0

Normal operating mode.

 

 

1

Request permission to stop the peripheral clock.

 

 

 

 

42

System Control

SPRUFX5A –October 2010 –Revised November 2010

 

 

Submit Documentation Feedback

Copyright © 2010, Texas Instruments Incorporated

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Users Guide Submit Documentation Feedback Contents List of Figures Submit Documentation Feedback List of Tables Submit Documentation Feedback Submit Documentation Feedback Read This First Related Documentation From Texas Instruments Related Documentation From Texas Instruments Submit Documentation Feedback Block Diagram Functional Block DiagramFFT Hardware Accelerator Using FFT Accelerator ROM routinesCPU Core AddressPower Management PeripheralsSystem Memory Program/Data Memory MapCPU Byte Address Range On-Chip Dual-Access RAM DaramDaram Blocks DaramOn-Chip Single-Access RAM Saram Saram BlocksSaram External Memory On-Chip Single-Access Read-Only Memory SaromSarom Blocks Asynchronous Emif Interface2 I/O Memory Map OverviewDevice Clocking DSP Clocking Diagram Clock Domains Functional Description PLL Output Frequency ConfigurationPowering Down and Powering Up the System PLL Multiplier and DividersClkout Pin SRCBit Field Value Description Clock Generator During Reset ConfigurationDSP Reset Conditions of the System Clock Generator Clock Generator After ResetEntering and Exiting the PLL Mode Register Bits Used in the Bypass ModeSetting the System Clock Frequency In the Bypass Mode Register Bits Used in the PLL ModeFrequency Ranges for Internal Clocks Setting the Output Frequency for the PLL ModeCV DD = 1.05 CV DD = 1.3 Clock Signal Name 10. PLL Clock Frequency RangesSoftware Steps To Modify Multiplier and Divider Ratios Clock Generator RegistersLock Time 12. Clock Generator RegistersClock Generator Control Register 1 CGCR1 1C20h Clock Generator Control Register 2 CGCR2 1C21hClock Generator Control Register 3 CGCR3 1C22h Clock Generator Control Register 4 CGCR4 1C23hInit Clock Configuration Register 2 CCR2 1C1Fh Clock Configuration Register 1 CCR1 1C1Eh17. Clock Configuration Register 1 CCR1 Field Descriptions 18. Clock Configuration Register 2 CCR2 Field DescriptionsPower Domains 19. Power Management Features20. DSP Power Domains Power Domains DescriptionClock Management CPU Domain Clock Gating Daram21. Idle Configuration Register ICR Field Descriptions Hwai Iporti Mporti Xporti Dporti Idlecfg CpuiHwai Valid Idle Configurations 22. Idle Status Register Istr Field Descriptions23. CPU Clock Domain Idle Requirements To Idle the Following Module/Port Clock Configuration ProcessPeripheral Domain Clock Gating XportMMCSD0CG DMA0CG Uartcg Spicg I2S3CG SysclkdisMMCSD0CG Anaregcg DMA3CG DMA2CG DMA1CG Usbcg Sarcg Lcdcg AnaregcgUsbclkstpack UrtclkstpackUrtclkstpreq UsbclkstpreqBit Field Clock Generator Domain Clock GatingUSB Domain Clock Gating EmfclkstpackUsbpwdn Usbsessend Usbvbusdet Usbpllen USB System Control Register Usbscr 1C32h27. USB System Control Register Usbscr Field Descriptions UsbpwdnUsboscbiasdis RTC Domain Clock GatingUsbdatpol UsboscdisStatic Power Management RTC Power Management Register Rtcpmgt 1930hRTC Interrupt Flag Register Rtcintfl 1920h 29. RTC Interrupt Flag Register Rtcintfl Field DescriptionsMode CV DD Voltage Internal Memory Low Power ModesRAM Sleep Mode Control Register 1 RAMSLPMDCNTLR1 1C28h 30. On-Chip Memory Standby Modes21. RAM Sleep Mode Control Register2 0x1C2A DV DDRTC, Ldoi Power Configurations31. Power Configurations IDLE3IDLE2 Procedure IDLE3 Procedure Core Voltage Scaling32. Interrupt Table HEX BytesIFR and IER Registers 33. IFR0 and IER0 Bit DescriptionsRtos Dlog Berr I2C Emif Gpio USB SPI RTC RCV3 XMT3 Interrupt Timing34. IFR1 and IER1 Bit Descriptions RtosTimer Interrupt Aggregation Flag Register Tiafr 1C14h Gpio Interrupt Enable and Aggregation Flag RegistersDMA Interrupt Enable and Aggregation Flag Registers Device Identification 35. Die ID RegistersDie ID Register 1 DIEIDR1 1C41h Die ID Register 0 DIEIDR0 1C40h36. Die ID Register 0 DIEIDR0 Field Descriptions 37. Die ID Register 1 DIEIDR1 Field DescriptionsDie ID Register 4 DIEIDR4 1C44h Die ID Register 3 DIEIDR3150 1C43h39. Die ID Register 3 DIEIDR3150 Field Descriptions 40. Die ID Register 4 DIEIDR4 Field DescriptionsDie ID Register 7 DIEIDR7 1C47h Die ID Register 6 DIEIDR6 1C46h42. Die ID Register 6 DIEIDR6 Field Descriptions 43. Die ID Register 7 DIEIDR7 Field DescriptionsDevice Configuration External Bus Selection Register Ebsr44. Ebsr Register Bit Descriptions Field Descriptions A17MODE LDO Control Register 7004hLDO Control A16MODE45. Rtcpmgt Register Bit Descriptions Field Descriptions Rtcpmgt Register Ldocntl Register 46. Ldocntl Register Bit Descriptions Field Descriptions47. LDO Controls Matrix Bgpd Bit Ldopd Bit Usbldoen BitOutput Slew Rate Control Register Osrcr 1C16h ClkoutsrEmifsr S15PD S15PD S14PD S13PD S12PD S11PD S10PDS05PD S04PD S03PD S02PD S01PD S00PD S05PDINT1PU INT0PU Resetpu EMU01PU Tdipu Tmspu Tckpu A20PD A19PD A18PD A17PD A16PD A15PDINT1PU A20PD PD15PDDMA Controller Configuration 52. Channel Synchronization Events for DMA Controllers DMA Configuration RegistersDMA Synchronization Events 53. System Registers Related to the DMA Controllers55. DMA Interrupt Enable Register Dmaier Field Descriptions 54. DMA Interrupt Flag Register Dmaifr Field DescriptionsCH0EVT Peripheral ResetCH1EVT CH3EVTCount Peripheral Software Reset Counter Register Psrcr 1C04hPeripheral Reset Control Register Prcr 1C05h PG4RSTEmif and USB Byte Access PG3RSTBytemode Setting CPU Access to USB Register 60. Effect of Bytemode Bits on Emif Accesses61. Effect of Usbscr Bytemode Bits on USB Access Emif System Control Register Escr 1C33hEmif Clock Divider Register Ecdr 1C26h 63. Emif Clock Divider Register Ecdr Field DescriptionsEdiv Products Applications DSPRfid

TMS3320C5515 specifications

The Texas Instruments TMS3320C5515 is a highly specialized digital signal processor (DSP) designed for a wide range of applications, including telecommunications, audio processing, and other signal-intensive tasks. As part of the TMS320 family of DSPs, the TMS3320C5515 leverages TI's extensive experience in signal processing technology, delivering robust performance and reliability.

One of the main features of the TMS3320C5515 is its 32-bit architecture, which allows for a high level of precision in digital signal computation. The processor is capable of executing complex mathematical algorithms, making it suitable for tasks that require high-speed data processing, such as speech recognition and audio filtering. With a native instruction set optimized for DSP applications, the TMS3320C5515 can perform multiply-accumulate operations in a single cycle, significantly enhancing computational efficiency.

The TMS3320C5515 employs advanced technologies including a Harvard architecture that separates instruction and data memory, enabling simultaneous access and improving performance. Its dual data buses enhance throughput by allowing multi-channel processing, making it particularly effective for real-time applications where timely data manipulation is critical. The device supports a wide range of peripherals, facilitating connections to various sensors and communication systems, which is vital in embedded applications.

In terms of characteristics, the TMS3320C5515 operates at an impressive clock speed, providing the computational power necessary to handle demanding tasks. The device is optimized for low power consumption, making it ideal for battery-operated applications without sacrificing performance. Its flexibility in processing algorithms also allows it to be readily adapted for specific requirements, from audio codecs to modems.

Another noteworthy aspect is the extensive development ecosystem surrounding the TMS3320C5515, which includes software tools, libraries, and support resources designed to accelerate the development process. This allows engineers and developers to bring their projects to market more quickly while minimizing risk.

Overall, the Texas Instruments TMS3320C5515 stands out as a powerful DSP solution, equipped with features that cater to the needs of various industries. Its combination of performance, efficiency, and versatile application makes it an attractive choice for engineers working in signal processing.
Top Page Image Contents