13.SERVICING - The user should not attempt to service the unit beyond that described in the user operating instructions. All other servicing should be referred to qualified service personnel.
14.CLEANING - Disconnect from mains power supply before cleaning. Do not use liquid or spray cleaners, only use a damp cloth. Follow the care and maintenance instructions in this manual.
15.LIGHTNING - During lightning and longer periods of
16.SAFETY CHECK - After servicing the unit ask the customer service for a safety check.
17.OVERLOAD - To avoid fire and electric shock do not overload wall outlets and convenience receptacles.
18.ELECTROSTATIC DISCHARGE - Disconnect from mains power supply and remove batteries if unit malfunctions. Reconnect after a short time.
CAUTION
THIS CD PLAYER IS A CLASS I LASER PRODUCT. HOWEVER, THIS CD PLAYER USES A VISIBLE/INVISIBLE LASER BEAM, WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE CD PLAYER CORRECTLY AS INSTRUCTED.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR THE DEVICE YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK AND ANNOYING INTERFERENCE USE ONLY THE RECOMMENDED ACCESSORIES.
INSTALLATION
Select the mounting location where the unit will not interfere with the normal driving function of the driver.
Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly.
Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.
Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle.
Install the unit where it does not get in the driver’s way and cannot injure the passengers if there is a sudden stop, like an emergency stop.
WIRING DIAGRAM |
|
|
| |
ANTENNA PLUG |
|
|
| |
| ISO CONNECTOR |
|
| |
MEMORY (B+) YELLOW | FUSED |
|
| |
BLACK (GND) |
| FILTER |
|
|
| BOX 1A |
|
| |
|
| & 7A |
|
|
RED (B+) |
| FUSES | RCA LINE OUT | RED R |
BLUE AUTO ANT |
| 0.5 A | WHITE L | |
| FUSE | |||
FRONT |
|
| FRONT | |
WHITE |
| GRAY | ||
LEFT |
|
|
|
| WHITE / BLACK |
|
|
| GRAY / BLACK |
|
|
|
|
|
| RIGHT | ||
|
|
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
SP |
|
|
|
|
| GREEN |
|
|
| VIOLET |
|
|
|
|
|
| SP | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
REAR |
|
|
|
|
| GREEN / BLACK |
|
|
| VIOLET / BLACK |
|
|
|
|
|
|
| REAR |
|
|
|
|
|
|
|
|
| ||||||||||
DIN front / rear-mount
This unit can be properly installed either from "front" (conventional DIN
For details, refer to the following illustrated installation methods.
| TO BOOST UP THE CAPABILITY OF | |
METAL STRAP | PLEASE FIX THE METAL STRAP ON THE METAL | |
CONNECTED TO THE BOTTOM BRACKET OF THE CAR. | ||
|
SELECT THE PROPER
FIXER FOR FIXING THE
SLIDING METAL HOUSING.
If the installation angle exceeds 30º the unit might not perform well.
30˚
Avoid installing the unit where it is subjected to high temperature, such as from direct sunlight, hot air from the heating ducts, or where subjected to dust, dirt or excessive vibration.
DASH BOARD
SLIDING METAL HOUSING
TO DRAW THE CHASSIS OUT OF THESLIDING METAL HOUSING, INSERTTHE LEFT AND RIGHT KEY PLATESINTO THE RIGHT POSITION OF THE 2 SIDES OF CHASSIS.
UNIT CHASSIS
PLASTIC TRIM OUT
FRONT PANEL
18. |
| 19. |
|
|
|