Weider WESY47330 user manual Tighten the M10 Nylon Locknuts 101 used in steps 1-3

Page 10

7.Press a 50mm x 75mm Inner Cap (46) into the Top Frame (9).

Slide the welded tubes on the Top Frame (9) over the upper ends of the Weight Guides (18, 19).

Attach the Top Frame (9) to the Butterfly Upright

(2)with two M10 x 75mm Bolts (82) and two M10 Nylon Locknuts (101). Do not tighten the

Locknuts yet.

Attach the Top Frame (9) to the Weight Guides (18, 19) with four M10 x 45mm Bolts (51) and four M10 Nylon Locknuts (101). Do not tighten the Locknuts yet.

8.Press a 50mm Thick Square Inner Cap (47) into the Sliding Seat Frame (8). Press a 50mm Square Inner Cap (45) into the indicated end of the Seat Adjustment Frame (4). Press the Metal Plate (44) and the 50mm Angled Outer Cap (43) onto the other end of the Seat Adjustment Frame.

Tighten a “T”-handle (59)into the Sliding Seat Frame (8). Turn the “T”-handle counterclockwise to loosen it. Pull out the handle as far as possible and slide the Seat Adjustment Frame (4) into the Sliding Seat Frame. Release the handle and let it engage one of the adjustment holes in the Seat Adjustment Frame. Then, tighten the handle.

9.Attach the Seat Adjustment Frame (4) to the Leg Press Base (3) with four M10 x 65mm Carriage Bolts (88) and four M10 Nylon Locknuts (101).

Tighten the M10 Nylon Locknuts (101) used in steps 1–3 and 7–9.

7
		9
	101		101
		82
		51
		2
46		18
	19
8	47
	47
		8
	59
45
		44	43
	4
9
	88
		88
101
	101	4
		101
	3
			101

10

Image 10

Contents Model No. WESY47330 Serial No QUESTIONS?Customer HOT Line Table of Contents Decal Important Precautions Dimensions Before YOU BeginAssembly Make Assembly Easier for YourselfFrame Assembly Tighten the Locknuts yet Locknuts yetPage Tighten the M10 Nylon Locknuts 101 used in steps 1-3 Lubricate the four 56mm Round Bushings 53 with grease Repeat this step with the Right Butterfly ArmPress Base 3 in the same manner Repeat with the other Seat ArmOvertighten the Locknut the Press Arm must Locknuts yet. Make sure the warining decal isBe between the Leg Press Brackets 16 Tighten the M10 Nylon Locknuts 101 usedPage Page Page Page Identify the Leg Press Cable 65. Attach Trap is oriented to hold the Cable Groove of the Pulley101 100 Large Ball Weight system Sure the Cable Trap is oriented to holdPage Seat Assembly Holes should Be closer to This end 101 Page Repeat this step with the other Butterfly Pin Attaching the Accessories to a Pulley Station AdjustmentsChanging the Weight Setting Using the LEG Lever LockConverting the Butterfly Arms Adjusting the SeatAttaching the Curl PAD Lbs Left Top Weight Resistance ChartWeight LEG High Butter Press LOW Pulley FLY ARM Lever BottomLower Short Stack Cable Cable DiagramsUpper Short Stack Cable Leg Press CableButterfly Cable Lat CableAb Cable Troubleshooting Tightening the CablesFour Basic Types of Workouts Exercise GuidelinesPersonalizing Your Exercise Program Cooling Down Muscle ChartStaying Motivated Aerobic Exercise Exercise Weight Sets RepsDate Thursday Aerobic Exercise DateMonday Part Identification Chart Page Page Part LIST-Model No. WESY47330 Qty DescriptionExploded Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT