Weider WESY47330 user manual Tighten the Locknuts yet

Page 8

3. Press a 50mm Thick Square Inner Cap (47) into	3
the Leg Lever Base (5). Press two 50mm x 75mm	3
the Leg Lever Base (5). Press two 50mm x 75mm
Inner Caps (46) into the Foot Plate (6).		2
		2		47
Attach the Leg Lever Base (5) to the Butterfly				47
Attach the Leg Lever Base (5) to the Butterfly
Upright (2) with two M10 x 75mm Bolts (82), an
M10 x 95mm Bolt (105), an M10 Washer (99),
and three M10 Nylon Locknuts (101). Do not				5
tighten the Locknuts yet.		101		5
		105
Attach the Foot Plate (6) to the Leg Lever Base	99
(5) with two M10 x 65mm Carriage Bolts (88) and	99			101	46
two M10 Nylon Locknuts (101). Do not tighten	101			101
two M10 Nylon Locknuts (101). Do not tighten	101
the Locknuts yet.	82
		101
		46			88
					88
				6
4. Insert the two Weight Guides with Rings (19) into	4
the indicated holes in the Base (1). Attach the	4
the indicated holes in the Base (1). Attach the
Weight Guides with Rings to the Base with two
M10 x 65mm Bolts (80), four M10 Washers (99),
four 12.5mm Spacers (69), and two M10 Nylon
Locknuts (101).
Insert the two Weight Guides (18) into the indicat-		19			18
		19

ed holes in the Base (1). Attach the Weight
Guides to the Base with two M10 x 65mm Bolts
(80), four M10 Washers (99), four 12.5mm
Spacers (69), and two M10 Nylon Locknuts (101).
	101	99
		99
					1
		69
	99				69
					99
		69	99		80
			99		80

8

Image 8

Contents Customer HOT Line QUESTIONS?Model No. WESY47330 Serial No Table of Contents Decal Important Precautions Dimensions Before YOU BeginAssembly Make Assembly Easier for YourselfFrame Assembly Tighten the Locknuts yet Locknuts yetPage Tighten the M10 Nylon Locknuts 101 used in steps 1-3 Lubricate the four 56mm Round Bushings 53 with grease Repeat this step with the Right Butterfly ArmRepeat with the other Seat Arm Overtighten the Locknut the Press Arm mustPress Base 3 in the same manner Locknuts yet. Make sure the warining decal isBe between the Leg Press Brackets 16 Tighten the M10 Nylon Locknuts 101 usedPage Page Page Page Identify the Leg Press Cable 65. Attach Trap is oriented to hold the Cable Groove of the Pulley101 100 Large Ball Weight system Sure the Cable Trap is oriented to holdPage Seat Assembly Holes should Be closer to This end 101 Page Repeat this step with the other Butterfly Pin Adjustments Changing the Weight SettingAttaching the Accessories to a Pulley Station Using the LEG Lever LockAttaching the Curl PAD Adjusting the SeatConverting the Butterfly Arms Weight Resistance Chart Weight LEG High Butter Press LOW Pulley FLY ARM LeverLbs Left Top BottomCable Diagrams Upper Short Stack CableLower Short Stack Cable Leg Press CableAb Cable Lat CableButterfly Cable Troubleshooting Tightening the CablesPersonalizing Your Exercise Program Exercise GuidelinesFour Basic Types of Workouts Staying Motivated Muscle ChartCooling Down Exercise Weight Sets Reps DateAerobic Exercise Thursday Aerobic Exercise DateMonday Part Identification Chart Page Page Part LIST-Model No. WESY47330 Qty DescriptionExploded Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty