Weider WESY37530 user manual Make Assembly Easier for Yourself

Page 5

ASSEMBLY

Make Assembly Easier for Yourself

Everything in this manual is designed to ensure that the weight system can be assem- bled successfully by anyone. Before begin- ning assembly, make sure to read the information on this page. This brief intro- duction will save you much more time than it takes to read it.

Assembly Requires Two Persons

For your convenience and safety, assemble the weight system with the help of another person.

Set Aside Enough Time

Due to the many features of the weight system, the assembly process will require several hours. By setting aside plenty of time and by deciding to make the task enjoyable, assembly will go smoothly. You may want to assemble the weight system over a couple of evenings.

Select a Location for the Weight System

Because of its weight and size, the weight system should be assembled in the location where it will be used. Make sure that there is enough room to walk around the weight system as you assemble it.

How to Unpack the Box

To make assembly as easy as possible, we have divided the assembly process into four stages. The parts needed for each stage are found in individual bags. Important: Wait until you begin each stage to open the parts bag for that stage. Place all parts of the weight system in a cleared area and remove the packing materials. Do not dispose of the packing materials until assembly is completed.

Make sure you have the following tools:

• Two adjustable wrenches

• One standard screwdriver

• One phillips screwdriver

• One rubber mallet

You will also need grease or petroleum jelly, a small amount of soapy water, and clear tape or masking tape.

Note: Assembly will be more convenient if you have a socket set, a set of open-end or closed-end wrenches, or a set of ratchet wrenches.

How to Identify Parts

To help you identify the small parts used in assembly, we have included a PART IDENTIFICATION CHART in the center of this manual. Place the chart on the floor and use it to easily identify parts during each assembly step. Note: Some small parts may have been pre-attached. If a part is not in the parts bag, check to see if it has been pre-attached.

How to Orient Parts

As you assemble the weight system, make sure that all parts are oriented exactly as shown in the draw- ings.

Tightening Parts

Tighten all parts as you assemble them, unless instructed to do otherwise.

Questions?

If you have questions after reading the assembly instructions, please call our Customer Service Department at 1-800-999-3756.

The Four Stages of the Assembly Process

Frame Assembly—You will begin by assembling

Cable Assembly—During this stage you will

the base and the uprights that form the skeleton of

attach the cables and pulleys that connect the

the weight system.

arms to the weights.

Arm Assembly—During this stage you will

Seat Assembly—During the final stage you will

assemble the arms and the leg lever.

assemble the seats and the backrests.

 

 

5

Image 5
Contents Customer HOT Line QUESTIONS?Model No. WESY37530 Serial No Table of Contents Important Precautions Left Side Before YOU BeginRight Side Make Assembly Easier for Yourself AssemblyTighten the Locknuts yet Frame AssemblyPage Do not tighten the Locknuts yet Pin not shown are on the indicated side Guides 9. Make sure the slots for the WeightOn the bottom of the Weights Tighten the M10 Nylon Locknuts 75 used in steps Locknuts yetOpen the part bag labeled ARM Assembly Arm AssemblyOuter Cap 47. Make sure the teeth on EasilyRings are toward the Cap, as shown Cap onto the axle. Repeat with the Right Fly PivotCable Trap is turned to hold the Cable Groove of the Pulley Cable is over the welded bar insideDo not tighten the Locknut yet Locate the Short Cable 62. Attach the eyeletPage Page Page Page Cable Trap is turned to hold the Cable Place Remove the M10 Nylon Locknut 75 used Step Remove the M10 Nylon Locknut 75 used in step Locate and open the parts bag labeled Seat AssemblyPage Adjusting the Backrests AdjustmentsAdjusting the Curl PAD Store the Curl Pad out of the way of the weight systemChanging the Weight Setting Lbs Weight Resistance ChartWeight High Press LEG Butter LOW Pulley ARM FLY ARM Lever Tightening the Cables TroubleshootingShort Cable Cable DiagramsHigh Cable Low Cable Exercise Guidelines Staying Motivated Muscle ChartCooling Down Date Exercise Weight Sets RepsAerobic Exercise Thursday Aerobic Exercise DateR1003A Part Identification CHART- Model No. WESY37530Page Page Qty Description Part LIST-Model No. WESY37530WESY37530 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty