Weider WESY37530 user manual Remove the M10 Nylon Locknut 75 used in step

Page 21

58.Remove the M10 Nylon Locknut (75) used in step 50.

Attach the Low Cable (63) to the M10 x 110mm Bolt (90) in the Right Upright (5) with two M10 Washer (74), and the M10 Nylon Locknut (75).

Seat Assembly

59.Locate and open the parts bag labeled “SEAT ASSEMBLY.”

Attach the Seat (26) with the serial number decal to the Left Seat Frame (4) with four M6 x 16mm Screws (79).

Attach the other Seat (26) to the Right Seat Frame (not shown) in the same manner.

60.Press a 38mm Square Inner Cap (44) into a Backrest Frame (16). Attach a Backrest (27) to the Backrest Frame with four M6 x 20mm Screws (64).

Pull the Backrest Knob (48) on the Left Upright

(6)out as far as it will go and insert the Backrest Frame (16) into the Upright. Engage the Knob into one of the holes in the Backrest Frame, and turn the Knob clockwise until it is tight.

Attach the other Backrest to the Right Upright (not shown) in the same manner. Note: The tops of the Backrests should be closer to the Uprights than the bottoms.

61.Press the two 19mm Round Inner Caps (24) into the ends of a Pad Tube (17). Insert the Pad Tube into the tube on the Left Leg (8). Slide the two Foam Pads (25) onto the Pad Tube as shown.

Assemble the other Pad Tube (17) to the Leg Lever (18) in the same manner.

58
	5		74
	90
		63	75
		63
59
			26
	4		Wide
	4		End
		79
Serial Number Decal
60
6 44	64
	64		27
			27
48
		16
61
			17
			18
		8
			25
			24
25		17
		17
	24

21

Image 21

Contents QUESTIONS? Model No. WESY37530 Serial NoCustomer HOT Line Table of Contents Important Precautions Before YOU Begin Right SideLeft Side Make Assembly Easier for Yourself AssemblyTighten the Locknuts yet Frame AssemblyPage Do not tighten the Locknuts yet Guides 9. Make sure the slots for the Weight On the bottom of the WeightsPin not shown are on the indicated side Tighten the M10 Nylon Locknuts 75 used in steps Locknuts yetOpen the part bag labeled ARM Assembly Arm AssemblyOuter Cap 47. Make sure the teeth on EasilyRings are toward the Cap, as shown Cap onto the axle. Repeat with the Right Fly PivotCable Trap is turned to hold the Cable Groove of the Pulley Cable is over the welded bar insideDo not tighten the Locknut yet Locate the Short Cable 62. Attach the eyeletPage Page Page Page Cable Trap is turned to hold the Cable Place Remove the M10 Nylon Locknut 75 used Step Remove the M10 Nylon Locknut 75 used in step Locate and open the parts bag labeled Seat AssemblyPage Adjusting the Backrests AdjustmentsAdjusting the Curl PAD Store the Curl Pad out of the way of the weight systemChanging the Weight Setting Weight Resistance Chart Weight High Press LEG Butter LOW Pulley ARM FLY ARM LeverLbs Tightening the Cables TroubleshootingCable Diagrams High CableShort Cable Low Cable Exercise Guidelines Muscle Chart Cooling DownStaying Motivated Date Exercise Weight Sets RepsAerobic Exercise Thursday Aerobic Exercise DateR1003A Part Identification CHART- Model No. WESY37530Page Page Qty Description Part LIST-Model No. WESY37530WESY37530 Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT