Weider WESY37530 user manual Do not tighten the Locknuts yet

Page 8

6.Press a 50mm x 75mm Inner Cap (45) into the Right Seat Frame (3).

Orient the Right Seat Frame (3) as shown. Attach the Right Seat Frame to the Right Leg (7) with two M10 x 78mm Bolts (86), two M10 Washers (74), and two M10 Nylon Locknuts (75). Do not tighten the Locknuts yet.

Attach the Right Seat Frame (3) to the Right Upright (5) with two M10 x 78mm Bolts (86), two M10 Washers (74), and two M10 Nylon Locknuts (75). Do not tighten the Locknuts yet.

7.Press a Square Bushing (55) into the Left Leg

Attach a Leg Bumper (49) to the Left Leg (8) with an M4 x 25mm Self-tapping Screw (77) and an M4 Washer (84).

Attach the Left Leg (8) to the Left Base (2) with the indicated two M10 x 53mm Carriage Bolts

(83)and two M10 Nylon Locknuts (75). Do not tighten the Locknuts yet.

8.Orient the Left Seat Frame (4) as shown. Make sure the brackets are closer to the Left Leg

(8).Attach the Left Seat Frame to the Left Leg with two M10 x 78mm Bolts (86), two M10 Washers (74), and two M10 Nylon Locknuts (75).

Do not tighten the Locknuts yet.

Attach the Left Seat Frame (4) to the Left Upright

(6)with two M10 x 78mm Bolts (86), two M10

Washers (74), and two M10 Nylon Locknuts (75).

Do not tighten the Locknuts yet.

6

 

86

 

 

 

 

 

75

 

 

 

 

74

 

86

3

 

 

 

 

86

 

 

 

 

 

74

 

 

86

 

5

 

 

 

 

 

 

45

 

 

 

74

 

 

 

 

 

7

 

 

75

 

 

 

 

74

 

 

 

7

 

 

 

 

 

 

55

 

 

 

 

49

84

 

 

 

8

 

 

 

 

 

 

77

 

 

75

 

 

 

 

75

 

 

 

2

 

 

 

 

83

 

 

8

 

 

 

 

 

 

86

 

 

75

74

4

 

 

 

 

86

 

 

 

 

 

 

86

 

 

 

74

 

 

 

 

 

Bracket

86

 

 

 

6

 

 

 

 

 

 

74

 

 

 

8

75

 

 

 

 

 

 

 

 

74

8

Image 8
Contents Customer HOT Line QUESTIONS?Model No. WESY37530 Serial No Table of Contents Important Precautions Left Side Before YOU BeginRight Side Assembly Make Assembly Easier for YourselfFrame Assembly Tighten the Locknuts yetPage Do not tighten the Locknuts yet Pin not shown are on the indicated side Guides 9. Make sure the slots for the WeightOn the bottom of the Weights Locknuts yet Tighten the M10 Nylon Locknuts 75 used in stepsArm Assembly Open the part bag labeled ARM AssemblyEasily Outer Cap 47. Make sure the teeth onRings are toward the Cap, as shown Cap onto the axle. Repeat with the Right Fly PivotCable is over the welded bar inside Cable Trap is turned to hold the Cable Groove of the PulleyLocate the Short Cable 62. Attach the eyelet Do not tighten the Locknut yetPage Page Page Page Cable Trap is turned to hold the Cable Place Remove the M10 Nylon Locknut 75 used Step Locate and open the parts bag labeled Seat Assembly Remove the M10 Nylon Locknut 75 used in stepPage Adjustments Adjusting the BackrestsAdjusting the Curl PAD Store the Curl Pad out of the way of the weight systemChanging the Weight Setting Lbs Weight Resistance ChartWeight High Press LEG Butter LOW Pulley ARM FLY ARM Lever Troubleshooting Tightening the CablesShort Cable Cable DiagramsHigh Cable Low Cable Exercise Guidelines Staying Motivated Muscle ChartCooling Down Exercise Weight Sets Reps DateAerobic Exercise Thursday Aerobic Exercise DatePart Identification CHART- Model No. WESY37530 R1003APage Page Part LIST-Model No. WESY37530 Qty DescriptionWESY37530 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty