Weider WESY37530 Easily, Outer Cap 47. Make sure the teeth on, Rings are toward the Cap, as shown

Page 12

18. Press a 50mm Square Inner Cap (43) into a

18

 

 

Press Arm (15). Press two 25mm Round Inner

 

 

 

 

 

Caps (65) into the Press Arm.

 

 

 

Wet the handles on the Press Arm (15) with

 

 

 

soapy water. Slide two Grips (68) onto the han-

 

 

 

dles.

 

68

43

 

 

 

15

 

Attach the Press Arm (15) to the Press Frame

 

 

 

 

 

(14) with two M10 x 70mm Bolts (87) and two

 

 

 

M10 Nylon Locknuts (75).

 

 

65

 

 

 

Attach the other Press Arm (15) to the Press

 

15

 

Frame (14) in the same manner.

 

 

 

75

 

 

 

 

 

87

14

 

 

 

 

19. Press two 50mm Square Inner Caps (43) into the

19

 

 

Leg Lever (18).

 

 

8

43

 

 

 

 

 

 

Lubricate an M10 x 78mm Bolt (86) with grease.

 

75

 

Orient the Leg Lever (18) as shown and attach it

 

 

 

to the Left Leg (8) with the Bolt and an M10

86

18

 

Nylon Locknut (75). Do not overtighten the

 

 

 

Locknut; the Leg Lever must be able to pivot

Lubricate

 

Small

easily.

 

Slot

 

 

43

 

20. Lubricate both axles on the Left Top Frame (11)

20

 

 

with grease.

 

 

 

 

11

 

 

 

Press a 38mm Square Inner Cap (44) into the

 

 

Axle

Left Fly Pivot (21). Slide the Left Fly Pivot onto

 

 

 

 

 

the indicated axle on the Left Top Frame (11). Set

 

 

 

two 25mm Retainer Rings (53) on a 25mm Round

Axle

22

21

Outer Cap (47). Make sure the teeth on the

 

Rings are toward the Cap, as shown in the

53

44

53

inset drawing. Tap the Retainer Rings and Outer

 

Cap onto the axle. Repeat with the Right Fly

47

 

47

Pivot (22).

 

 

 

 

 

 

21. Press a 50mm Square Inner Cap (43) into a

21

 

 

Butterfly Arm (20).

 

 

 

 

 

Wet a Fly Handle (66) and the inside of a Long

 

20

 

 

 

 

Foam Pad (33) with soapy water. Slide the Foam

 

33

66

Pad onto the Handle.

 

 

 

Attach a Fly Handle (66) to the Butterfly Arm (20)

 

 

 

with two M10 x 25mm Button Screws (60) and

 

 

 

two M10 Washers (74).

 

 

 

Repeat this step with the other Butterfly Arm

60

74

 

 

 

(not shown). Make sure that the Fly Handle is

 

43

 

oriented as shown in step 22.

 

 

 

 

12

 

 

Image 12
Contents QUESTIONS? Model No. WESY37530 Serial NoCustomer HOT Line Table of Contents Important Precautions Before YOU Begin Right SideLeft Side Assembly Make Assembly Easier for YourselfFrame Assembly Tighten the Locknuts yetPage Do not tighten the Locknuts yet Guides 9. Make sure the slots for the Weight On the bottom of the WeightsPin not shown are on the indicated side Locknuts yet Tighten the M10 Nylon Locknuts 75 used in stepsArm Assembly Open the part bag labeled ARM AssemblyEasily Outer Cap 47. Make sure the teeth onRings are toward the Cap, as shown Cap onto the axle. Repeat with the Right Fly PivotCable is over the welded bar inside Cable Trap is turned to hold the Cable Groove of the PulleyLocate the Short Cable 62. Attach the eyelet Do not tighten the Locknut yetPage Page Page Page Cable Trap is turned to hold the Cable Place Remove the M10 Nylon Locknut 75 used Step Locate and open the parts bag labeled Seat Assembly Remove the M10 Nylon Locknut 75 used in stepPage Adjustments Adjusting the BackrestsAdjusting the Curl PAD Store the Curl Pad out of the way of the weight systemChanging the Weight Setting Weight Resistance Chart Weight High Press LEG Butter LOW Pulley ARM FLY ARM LeverLbs Troubleshooting Tightening the CablesCable Diagrams High CableShort Cable Low Cable Exercise Guidelines Muscle Chart Cooling DownStaying Motivated Exercise Weight Sets Reps DateAerobic Exercise Thursday Aerobic Exercise DatePart Identification CHART- Model No. WESY37530 R1003APage Page Part LIST-Model No. WESY37530 Qty DescriptionWESY37530 Ordering Replacement Parts Limited WarrantyIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT