Weider WESY37530 user manual

Page 17

39. Wrap the Low Cable (63) around a “V”-pulley (40).

39

 

 

Attach the “V”-pulley and a Large Cable Trap (39)

 

 

 

 

 

to the Left Fly Pivot (21) with an M10 x 91mm Bolt

91

39

 

(91), an M10 Washer (74), and an M10 Nylon

 

 

 

 

 

 

Locknut (75). Make sure that the Cable Trap is

63

40

 

turned to hold the Cable in the groove of the

 

 

 

 

 

 

“V”-pulley.

 

 

 

 

 

21

 

 

 

74

 

 

 

75

 

40. Wrap the Low Cable (63) around a “V”-pulley (40).

40

 

 

Attach the “V”-pulley and a Large Cable Trap (39)

 

 

 

75

 

to the center bracket on the Left Upright (6) with

 

 

39

 

 

an M10 x 60mm Bolt (82) and an M10 Nylon

40

 

Locknut (75). Make sure that the Cable Trap is

 

 

63

 

 

turned to hold the Cable in the groove of the

 

 

 

 

 

“V”-pulley.

82

 

 

 

 

 

 

 

6

 

41. Wrap the Low Cable (63) around a “V”-pulley (40).

41

 

 

Attach the “V”-pulley and a Large Cable Trap (39)

 

 

91

 

 

to the Right Fly Pivot (22) with an M10 x 91mm

39

 

 

 

Bolt (91), an M10 Washer (74), and an M10 Nylon

 

 

 

40

 

Locknut (75). Make sure that the Cable Trap is

 

 

 

63

 

turned to hold the Cable in the groove of the

 

 

 

 

 

“V”-pulley.

 

 

 

 

74

 

 

 

 

 

22

 

75

 

 

42. Note: The “V”-pulley (40) attached in step 41

42

 

 

is not shown in this step for clarity.

 

 

 

 

 

Wrap the Low Cable (63) over a “V”-pulley (40).

 

 

 

Attach the “V”-pulley and a Large Cable Trap (39)

 

 

 

to the bracket on the Left Upright (6) with an M10

 

 

 

x 60mm Bolt (82) and an M10 Nylon Locknut (75).

40

 

 

Make sure that the Cable Trap is turned to hold

 

 

 

the Cable in the groove of the “V”-pulley.

82

 

 

 

 

 

 

39

 

6

 

63

 

 

17

Image 17
Contents Customer HOT Line QUESTIONS?Model No. WESY37530 Serial No Table of Contents Important Precautions Left Side Before YOU BeginRight Side Make Assembly Easier for Yourself AssemblyTighten the Locknuts yet Frame AssemblyPage Do not tighten the Locknuts yet Pin not shown are on the indicated side Guides 9. Make sure the slots for the WeightOn the bottom of the Weights Tighten the M10 Nylon Locknuts 75 used in steps Locknuts yetOpen the part bag labeled ARM Assembly Arm AssemblyOuter Cap 47. Make sure the teeth on EasilyRings are toward the Cap, as shown Cap onto the axle. Repeat with the Right Fly PivotCable Trap is turned to hold the Cable Groove of the Pulley Cable is over the welded bar insideDo not tighten the Locknut yet Locate the Short Cable 62. Attach the eyeletPage Page Page Page Cable Trap is turned to hold the Cable Place Remove the M10 Nylon Locknut 75 used Step Remove the M10 Nylon Locknut 75 used in step Locate and open the parts bag labeled Seat AssemblyPage Adjusting the Backrests AdjustmentsAdjusting the Curl PAD Store the Curl Pad out of the way of the weight systemChanging the Weight Setting Lbs Weight Resistance ChartWeight High Press LEG Butter LOW Pulley ARM FLY ARM Lever Tightening the Cables TroubleshootingShort Cable Cable DiagramsHigh Cable Low Cable Exercise Guidelines Staying Motivated Muscle ChartCooling Down Date Exercise Weight Sets RepsAerobic Exercise Thursday Aerobic Exercise DateR1003A Part Identification CHART- Model No. WESY37530Page Page Qty Description Part LIST-Model No. WESY37530WESY37530 Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty