Whirlpool W10136970C manual DryingRackOption, ChangingCycles,Options andModifiers

Page 19

The DAMP DRY SIGNAL is useful when drying bedsheets/linens in a mixed load. When the signal goes off, open the door to stop the dryer, rearrange the load inside the dryer, close the door and restart the dryer to finish the drying cycle. Rearranging the load will aid in the drying process.

Press DAMP DRY SIGNAL until the desired volume (Loud, Soft or Off) glows green.

NOTE: The Damp Dry Signal is available only with the Automatic Cycles. The Damp Dry Signal is not a selectable option for the Sanitize cycle.

Cycle Signal

The End of Cycle Signal produces an audible sound when the drying cycle is finished. Promptly removing clothes at the end of the cycle reduces wrinkling.

Press CYCLE SIGNAL until the desired volume (Loud, Soft or Off) glows green.

NOTE: When the WRINKLE SHIELD™ feature is selected and the End of Cycle Signal is on, an audible sound will be emitted every 5 minutes until the clothes are removed, or the WRINKLE SHIELD™ feature is finished.

Button Sound

You can change the volume of the sound of the beeps. Press BUTTON SOUND until the desired volume (Loud, Soft or Off) glows green. The Power and Cancel buttons will still beep softly even when the Button Sound volume is set to Off.

Changing Modifiers and Options after pressing Start

You can change a Modifier or Option anytime before the selected Modifier or Option begins.

1.Press PAUSE/CANCEL once.

2.Select the new Modifier and/or Option.

3.Press and hold START to continue the cycle.

NOTE: If you happen to press Pause/Cancel twice, the program clears and your dryer shuts down. Restart the selection process.

Changing the Preset Dryness Level Settings

If all your loads on all Auto Dry cycles are consistently not as dry as you would like, you may change the preset Dryness Level settings to increase the dryness. This change will affect all of your Auto Dry cycles.

Your Dryness Level settings can be adjusted to adapt to different installations, environmental conditions or personal preference. There are 3 drying settings: 1 (factory preset dryness level),

2 (slightly dryer clothes, approximately 15% more drying time) and 3 (much dryer clothes, approximately 30% more drying time).

1.The Dryness Level settings cannot be changed while the dryer is running.

2.Press and hold the Dryness Level button for 5 seconds. The dryer will beep, and “CF” will be displayed for 1 second followed by the current drying setting.

3.To select a new drying setting, press the Dryness Level key again until the desired drying setting is shown.

NOTE: While cycling through the settings, the current setting will not flash, but the other settings will flash.

4.Press START to save the drying setting.

5.The drying setting you selected will become your new preset drying setting for all Auto Dry cycles.

DryingRackOption

The drying rack is useful for drying items you would not necessarily want to tumble dry or that you would normally line dry (for example, sweaters).

To order, call the dealer from whom you purchased your dryer or refer to the “Assistance or Service” section. Ask for Part Number W10143399.

To use the drying rack

Do not remove the lint screen.

1.Open dryer door.

ChangingCycles,Options andModifiers

You can change Auto Cycles, Timed Cycles, Modifiers and Options anytime before pressing Start.

Three short tones sound if an unavailable combination is selected. The last selection will not be accepted.

Changing Cycles after pressing Start

1.Press PAUSE/CANCEL twice. This ends the current cycle.

2.Select the desired cycle and options.

3.Press and hold START. The dryer starts at the beginning of the new cycle.

NOTE: If you do not press Start within 5 minutes of selecting the cycle, the dryer automatically shuts off.

A

A. Front edge

19

Image 19
Contents W10136970C Electronic GAS DryerTable of Contents Dryer SafetyWhat to do if YOU Smell GAS ToolsandParts Installation InstructionsOptions LocationRequirements Recessed or closet installation Dryer on pedestal Recommended installation spacing for cabinet installationMobile home Additional installation requirements Closet installation Dryer onlyGas supply line Electrical RequirementsGas SupplyRequirements Gas TypeBurner input requirements Gas supply pressure testingIf using an existing vent system VentingRequirementsIf this is a new vent system Vent material PlanVentSystemDetermine vent path Optional exhaust installationsSpecial provisions for mobile home installations Alternate installations for close clearancesMakeGasConnection Install VentSystemInstall LevelingLegs Vent system chartConnectInletHose ConnectVentLevelDryer If the dryer will not start, check the following CompleteInstallationStartingYourDryer Dryer USETo use an Automatic Cycle To pause the dryer at any time PausingorRestartingStoppingYourDryer To stop your dryer at any timeDryingandCycleTips ControlLockedStatusLights Cycles Additional Features ChangingCycles,Options andModifiers DryingRackOptionAs needed cleaning CleaningtheDryerLocationCleaningtheLintScreen Every load cleaningVacation,StorageandMovingCare CleaningtheDryerInteriorRemovingAccumulatedLint WaterInletHosesDryerOperation TroubleshootingLoads are wrinkled Cycle time too shortLint on load Stains on load or drumIntheU.S.A AccessoriesInCanada Call Whirlpool Corporation Major Appliance WarrantyVotre sécurité et celle des autres est très importante Sécurité DE LA SécheuseOutillageetpièces Instructions D’INSTALLATIONPièces fournies Trousse dinversion de porte Pièces nécessairesPiédestal Nécessaire de superpositionDimensions de la sécheuse Exigencesd’emplacementIl vous faudra Installation dans un placard Sécheuse seulement Espacement recommandé pour linstallation dans un placardSpécifications électriques Linstallation dans une maison mobile exigeCanalisation d’arrivée de gaz AlimentationengazType de gaz Exigences concernant le raccordement au gazCanalisation d’arrivée de gaz de la sécheuse ExigencesconcernantlévacuationEn cas dutilisation du système dévacuation existant Évacuation Installations d’évacuation facultativesPlanificationdusystèmed’évacuation Brides de serrageDéterminer litinéraire dacheminement du conduit Autres installations où le dégagement est réduitTableau des systèmes dévacuation Installationdusystèmed’évacuationInstallationdespiedsdenivellement RaccordementaugazRaccordementduconduitd’évacuation Raccordementdes tuyauxdalimentationMiseàniveaudela sécheuse Acheverl’installationSi la sécheuse ne démarre pas, vérifier ce qui suit Miseenmarchedelasécheuse Utilisation DE LA SécheuseUtilisation dun programme automatique Utilisation dun programme manuel Comment fonctionnent les programmes automatiquesUtilisation dun programme Steam vapeur Pauseouremiseenmarche ArrêtdelasécheuseConseils pourleséchageetles programmes Programmes Témoins lumineuxTimed Dry séchage minuté Damp Dry séchage humidePréréglages des programmes automatiques Programmes manuelsCaractéristiquessupplémentaires Changement des programmes après avoir appuyé sur Start Changementdesprogrammes,optionset ModificateursOptiondegrilledeséchage Button Sound son des boutonsChaussures de tennis ou en Séchage sur grille Réglage Temp Durée Chandails en laineJouets rembourrés ou OreillersNettoyagedel’intérieurdelasécheuse Nettoyagedelemplacementde LasécheuseEntretien DE LA Sécheuse NettoyagedufiltreàcharpiePréparation de la sécheuse pour lhiver Réinstallation de la sécheuseTuyauxdalimentationdeau Changementdel’ampouled’éclairage DutambourFonctionnementdelasécheuse DépannageRésultatsdelasécheuse Charges froissées Temps de programme trop courtCharpie sur la charge Taches sur la charge ou sur le tambourAuxÉtats-Unis AccessoiresAuCanada W10136970C Garantie DES Gros Appareils Ménagers Whirlpool Corporation