Maytag MD-1 important safety instructions Select Temperature, Select Options, Select Cycle

Page 4

Using the Controls - Auto Dry Models

STEP 1

Select Temperature

In order to select the correct temperature, turn the Temperature control to one of four choices; Regular, Medium (select models), Delicate or Air Fluff.

DRYER TEMPS	LOAD TYPE

Regular	Sturdy cottons or labels marked
	Tumble Dry.

Medium	For wrinkle-free/permanent press
(select models)	synthetics, lightweight cottons
	labeled Tumble Dry Medium.

Delicate	For heat sensitive items labeled
	Tumble Dry Low or Tumble Dry
	Medium.

Air Fluff	Items which need freshening.
	Load tumbles with room
	temperature air. Use the Time
	Dry/Air Fluff cycle.

STEP 2

Select Options

Extended Tumble (select models)

Extended Tumble is provided to minimize wrinkles in the Auto Dry Wrinkle Control cycle. This feature provides an extra 60 minutes of unheated tumble action at the end of the cycle. Clothes can be removed any time during this portion of the cycle.

The additional 60 minutes of unheated tumbling can be canceled by turning the switch to Off.

End of Cycle Signal

When the cycle is complete, a signal will sound. On select models, the End of Cycle Signal can be turned down or Off.

Remove load immediately to reduce wrinkling.

STEP 3

Select Cycle

To select a cycle, rotate the control dial to the desired setting. When using an Auto Dry cycle, the control dial should point between More Dry and Less Dry for most loads.

Loads of larger or bulkier size may require the More Dry setting to completely dry the load. The Less Dry setting is best suited for lightweight fabrics or for leaving some moisture in the clothing at the end of the cycle.

Auto Dry Regular

The Auto Dry Regular cycle is designed to dry most cottons and linens. At the end of the cycle, the clothes are cooled for approximately 10 minutes to reduce wrinkling.

Auto Dry Wrinkle Control

The Auto Dry Wrinkle Control cycle is designed to dry wrinkle-free cottons, synthetic fabrics, double knits and permanent press fabrics automatically. At the end of the cycle, the clothes are cooled for approximately 25 minutes to reduce wrinkling. If the load is not removed from the dryer and Extended Tumble (select models) has been selected, the cycle will advance to Extended Tumble which provides additional unheated tumbling time. (See Step 2).

3

Image 4

Contents MD-1 Table of Contents TroubleshootingUse & Care Guide Auto Dry Models Sensor ModelsImportant Safety Instructions What You Need to Know About Safety InstructionsRecognize Safety Symbols, Words, Labels CanadaImportant Safety Do not sit on top of the clothes dryerSelect Options Select TemperatureSelect Cycle Push the Control Dial in to Start Time Dry/Air FluffDamp Dry select models Minutes of cool-down tumblingExtended Tumble Sensor RegularEnd of Cycle Chime Sensor Wrinkle ControlPush the Control Dial in to Start Select Dryness Setting Auto Temp preferred settingSelect Options if desired End of Cycle ChimeStart the Dryer Features Cycle Status LightsAccessories Clean the Lint FilterLoad the Dryer Properly Optional Drying RackCare & Cleaning Reversing the Door Reinstall four hinge attaching screws removed in StepReversing the Door Dryer Exhaust Tips Let a poor exhaust system Cause slow dryingRestrict your dryer with a poor exhaust system Use longer than necessary duct runs with many elbowsTroubleshooting Service & Warranty Dryer WarrantyFull One Year Warranty Limited WarrantyUtilisation des commandes Conseils pour l’évacuation MD-1Table des matières Importantes consignes Inversion de porte De sécuritéNuméro de modèle Ce qu’il faut savoir à propos des consignes de sécuritéQUE Faire S’IL Y a UNE Odeur DE GAZ Mesures de sécurité importantes Ne pas s’asseoir sur la sécheuseSélection de la température Sélection des optionsSélection du cycle Auto Dry Wrinkle Control antifroissementSéchage minuté/gonflant Pousser sur le sélecteur pour mettre en marcheDamp Dry séchage partiel, certains modèles Sélectionner un cycle Sensor Wrinkle Control AntifroissementExtended Tumble culbutage prolongé Sensor Regular Normal capteurCapteur Utilisation des commandes Commandes Choisissez du degré de séchageÉlectroniques Mise en marche de la sécheuseCaractéristiques Utilisation des commandes Commandes électroniquesVoyants de cycle Accessoires FonctionnementNettoyer le filtre à charpie Charger la sécheuse correctementNettoyage et Entretien Inversion de porte Inversion du sens d’ouverture de la porteConseils pour l’évacuation de l’air Utiliser un conduit trop long avec de nombreux coudesDes pannes Garantie et service après-vente Garantie de la sécheuseGarantie totale d’un an Garantie limitéeInstrucciones importantes De seguridad Uso de los controles MD-1 Tabla de materiasSugerencias para la operación Accesorios Cuidado y limpieza Si tiene preguntas llame a Asistencia al Cliente Canadá Ahora debe conocer las instrucciones de seguridadEN Caso DE QUE Perciba Olor a GAS Instrucciones importantes de seguridad Aviso y advertencia de seguridad importantes‘End of Cycle Signal’ Señal de fin de ciclo Selección de la temperaturaSelección de opciones Selección del cicloAutomático Presione el disco de control para empezar‘Auto Dry Regular’ ‘Auto Dry Wrinkle Control’ SecadoTEMPS, DE Presione el disco de control para empezar ‘Time Dry/Air Fluff’ Secado por tiempo/aire solamenteUso los controles Controles electrónicos Selección de temperaturaSelección de opciones si se desea Ajuste de selección del nivel de secado‘Regular’ Cont‘Refresh’ refrescar, modelos selectos Time Dry/Air Fluff secado por tiempo/aire Solamente‘Power Off’ apagado Encendido de la secadoraCaracterísticas Luces indicadoras de estado del cicloAccesorios Limpie el filtro para pelusaCargue adecuadamente la secadora Rejilla de secado opcionalCuidado y limpieza Inversión de la puerta Inversión de la puertaSugerencias para el escape Sistema de escape anualmenteProduce mucho Inmediatamente de la secadoraRuido Durante el ciclo de secadoGarantía y servicio Garantía de la secadoraUn año de garantía total Garantía limitada