Maytag MD-1 Select Options if desired, Select Dryness Setting, Auto Temp preferred setting

Page 8

Using the Controls - Electronic Controls

STEP 1

Select Temperature

Auto Temp (preferred setting)

When Auto Temp is selected, the dryer will automatically select the most appropriate drying temperature based on the cycle and dryness settings selected.

If you prefer not to use Auto Temp. turn the temperature selector knob to the desired setting.

DRYER TEMPS	LOAD TYPE

Regular	Sturdy cottons or labels marked
	Tumble Dry.

Medium	For wrinkle-free/permanent press
	synthetics, lightweight cottons or
	items labeled Tumble Dry Medium.

Low	For heat sensitive items labeled
	Tumble Dry Low or Tumble Dry
	Medium.

Air Fluff	Items which need freshening.
	Load tumbles with room
	temperature air. Use the Time
	Dry/Air Fluff cycle.

STEP 2

Select Options (if desired)

End of Cycle Chime

When the cycle is complete, an audible chime will sound. The chime will sound intermittently during Wrinkle Prevent. On select models, the volume of the chime can be adjusted. To turn the Chime off, turn the Chime selector knob to Off.

Wrinkle Prevent

Wrinkle Prevent provides approximately 95 minutes of intermittent tumbling in unheated air at the end of the cycle to reduce wrinkling. Set the Wrinkle Prevent switch On to activate this feature (select models). Some models automatically provide 30 minutes of Wrinkle Prevent at the end of the Wrinkle Control cycle only.

STEP 3

Select Dryness Setting

To select the dryness level, turn the Dryness Settings knob to the desired setting.

Most loads will use the Normal dry setting. Loads of larger or bulkier size may require the More dry setting to completely dry the load.

The Less dry setting is best suited for lightweight fabrics or for leaving some moisture in the load at the end of the cycle. Damp dry is designed to partially dry items. Use for items that lay flat or hang to dry.

STEP 4

Select Cycle

To select a cycle, rotate the cycle selector dial to the desired cycle. The indicator light by the cycle name will illuminate.

The dryer cycles are Sensor Dry cycles. Sensor Dry automatically senses the moisture in the load and shuts the dryer off when the selected dryness level (Damp dry to More dry) is reached.

7

Image 8

Contents MD-1 Table of Contents TroubleshootingUse & Care Guide Auto Dry Models Sensor ModelsImportant Safety Instructions What You Need to Know About Safety InstructionsRecognize Safety Symbols, Words, Labels CanadaImportant Safety Do not sit on top of the clothes dryerSelect Cycle Select TemperatureSelect Options Push the Control Dial in to Start Time Dry/Air FluffDamp Dry select models Minutes of cool-down tumblingExtended Tumble Sensor RegularEnd of Cycle Chime Sensor Wrinkle ControlPush the Control Dial in to Start Select Dryness Setting Auto Temp preferred settingSelect Options if desired End of Cycle ChimeStart the Dryer Features Cycle Status LightsAccessories Clean the Lint FilterLoad the Dryer Properly Optional Drying RackCare & Cleaning Reversing the Door Reinstall four hinge attaching screws removed in StepReversing the Door Dryer Exhaust Tips Let a poor exhaust system Cause slow dryingRestrict your dryer with a poor exhaust system Use longer than necessary duct runs with many elbowsTroubleshooting Service & Warranty Dryer WarrantyFull One Year Warranty Limited WarrantyUtilisation des commandes Conseils pour l’évacuation MD-1Table des matières Importantes consignes Inversion de porte De sécuritéQUE Faire S’IL Y a UNE Odeur DE GAZ Ce qu’il faut savoir à propos des consignes de sécuritéNuméro de modèle Mesures de sécurité importantes Ne pas s’asseoir sur la sécheuseSélection de la température Sélection des optionsSélection du cycle Auto Dry Wrinkle Control antifroissementDamp Dry séchage partiel, certains modèles Pousser sur le sélecteur pour mettre en marcheSéchage minuté/gonflant Sélectionner un cycle Sensor Wrinkle Control AntifroissementExtended Tumble culbutage prolongé Sensor Regular Normal capteurCapteur Utilisation des commandes Commandes Choisissez du degré de séchageÉlectroniques Mise en marche de la sécheuseVoyants de cycle Utilisation des commandes Commandes électroniquesCaractéristiques Accessoires FonctionnementNettoyer le filtre à charpie Charger la sécheuse correctementNettoyage et Entretien Inversion de porte Inversion du sens d’ouverture de la porteConseils pour l’évacuation de l’air Utiliser un conduit trop long avec de nombreux coudesDes pannes Garantie et service après-vente Garantie de la sécheuseGarantie totale d’un an Garantie limitéeSugerencias para la operación Accesorios Cuidado y limpieza MD-1 Tabla de materiasInstrucciones importantes De seguridad Uso de los controles EN Caso DE QUE Perciba Olor a GAS Ahora debe conocer las instrucciones de seguridadSi tiene preguntas llame a Asistencia al Cliente Canadá Instrucciones importantes de seguridad Aviso y advertencia de seguridad importantes‘End of Cycle Signal’ Señal de fin de ciclo Selección de la temperaturaSelección de opciones Selección del cicloAutomático Presione el disco de control para empezar‘Auto Dry Regular’ ‘Auto Dry Wrinkle Control’ SecadoTEMPS, DE Presione el disco de control para empezar ‘Time Dry/Air Fluff’ Secado por tiempo/aire solamenteUso los controles Controles electrónicos Selección de temperaturaSelección de opciones si se desea Ajuste de selección del nivel de secado‘Regular’ Cont‘Refresh’ refrescar, modelos selectos Time Dry/Air Fluff secado por tiempo/aire Solamente‘Power Off’ apagado Encendido de la secadoraCaracterísticas Luces indicadoras de estado del cicloAccesorios Limpie el filtro para pelusaCargue adecuadamente la secadora Rejilla de secado opcionalCuidado y limpieza Inversión de la puerta Inversión de la puertaSugerencias para el escape Sistema de escape anualmenteProduce mucho Inmediatamente de la secadoraRuido Durante el ciclo de secadoGarantía y servicio Garantía de la secadoraUn año de garantía total Garantía limitada