Simrad manual H1000 pilot installation manual

Page 1
ξ
ξ

CAUTION!

Use of solvent based or chemical cleaners on the displays will result in damage and invalidate the warranty

h1000 pilot installation manual

HB-1000I-02 English

WARNING!

An autopilot is a very useful navigational aid, but DOES NOT under any circumstance replace a human navigator.

Do not use automatic steering when:

ξ In heavy traffic areas or in narrow waters ξ In poor visibility or extreme sea conditions

ξ When in areas where use of an autopilot is prohibited by law

When using an autopilot:

ξ Do not leave the helm unattended

ξ Do not place any magnetic material or equipment near magnetic or fluxgate compass used in the autopilot system

Verify at regular intervals course and position of vessel Always switch OFF the autopilot in due time to avoid hazardous situations

Image 1
Contents H1000 pilot installation manual H1000 pilot ContentsH1000 pilot H1000 pilot calibration H1000 pilot display Description/installationDescription Siting the pilot display headPanel mounting Description/installation Mounting procedureSiting the compass unit H1000 compass unit DescriptionKey points when installing the rru Rudder reference unit Description/installation Rudder reference unit Minimum RRU Angle Rudder reference unit Linear feedback unitRam drive unit Rudder drive optionsHydraulic linear drives DescriptionRAM T0 Hydraulic Linear Drive RAM-T0-12V Midstroke Description/installation Rudder drive optionsRAM T1 and T2 Hydraulic Linear Drives RAM-T1-12V Midstroke RAM T3 Split Hydraulic Linear Drive RAM T3-24V MidstrokeHydraulic ram drive dimensions RAM-T0-12V Hydraulic ram drive dimensions T1-12V, T2-12V, T2-24V ‘R’CLIP ROD END AS H E R Tiller Bolt H1000 pilot Description/installation Type 3 ram bolt detail Key points on installation Description/installation Ram drive unit installationDescription/installation Layout of a typical ram drive unit Ram mounted parallel to vessel’s centre-line Mounting a hydraulic linear ram on a vertical bulkhead Description/installation Vertical bulkhead installation Type 0, type 1 and type 2 units Splitting the ram drive unitType 3 units Pump data Hydraulic drive pumpsType Hydraulic drive pump dimensions type 1Hydraulic drive pump installation Single station system example Dual station system example Hydraulic drive pump installation examplesPage Siting the acp unit Advanced control processor unit DescriptionGeneral wiring notes Acp unit installationCable and connection information Emc compliance All rudder drives heavy duty power cables Description/installation Pilot drive unit cablesWire colour coding and abbreviations Acp unit terminal detailsClutch voltage selection Acp dip switch location + + H1000 and alarm connections+ + Hand-held, mob and joystick+ + Description/installation Hydraulic ram drive connectionsPin Blue Wire Ram solenoid wiring detailsDescription/installation Hydraulic pump connections + + Description/installation Continuous drive unit connectionsOUT Direct paddle input connection+ + Description/installation Linear feedback connectionNon B&G Display Paddle Unit Non-B&G paddle connectionFuruno ad10 heading connection + +Intentionally Left Blank Hand-held controller Mounting procedureSiting the hand-held unit Optional devices Man overboard button mob Description Siting the man overboard alarm buttonAcp joystick Description Optional devicesSiting the joystick unit Calibration H1000 pilot calibration Linear feedback unit installation Rudder reference unit installationCompass installation Electronics installationAdjustment auto AdjustmentCalibration Speed calibration UnitsAdjustment ref Sea temperature unitsCalibration Calibration Calibrating the pilotCalibration menu Dockside calibrationCalibration Dockside calibration Hardover time Calibration Dockside calibrationsWaterline length Magnetic dip angle for boats faster than 20 knots only Magnetic dip angle compensation chartJoystick control Calibration Seatrial calibration Compass offset Calibration Compass calibrationCompass damping Compass swingH1000 pilot Calibration Seatrial calibration Engaging the h1000 pilot Setting the rudder amidships positionBoat lag Boat lag value table Setting the boat lag valueAutomatic rudder gain Checking the automatic rudder gain learningBoat Type Default Value Typical Values Setting the rudder gain manuallyManual rudder gain Rudder gain value tableTrouble shooting introduction TroubleshootingUncalibrated No rudder positionNo boat speed No drive detectedNo heading data Nmea data unstable No nmea informationPoor wind data Current trip limitPilot not steering a straight course Fault description