Korg V2 manual Set the recording level, Record, Press the Sequencer REC/WRITE key

Page 15

Then set the “BUS Select” that follows the insert effect you are using to 1/2.

AIn the Sequencer P0: Play/REC, Preference page, set “Track Select” to Audio Track 1.

BSpecify the recording method in “Recording Setup.” “Punch In”: unchecked

“Bounce”: unchecked

“Source BUS”: Indiv. 1/2

In the “Name” field, specify a name for the WAVE file that will be created. If you intend to record several takes for the same track, check “Take.” Routing the input (and associated effects) to the Indiv 1/2 Bus (instead of L/R) allows just the input signal to berecorded to the audio track, and not the entire output of the TRITON STUDIO.

If you had used the “Auto Sampling/HD Audio Setup” page menu command and selected HD Audio Track REC, the settings you have made up to this point would have been made automatically. This command automatically sets “Input,” “Track Select,” “Punch In,” “Bounce,” and “Source BUS.” (☞p.30)

Leave “Punch In” unchecked if you want to record from the beginning of the song or from the measure specified by “Location.”

If “Take” is unchecked, you can enter a file name of up to eight characters. If “Take” is checked, you can enter only six characters.

If you want the metronome to sound while you record, adjust the settings in “Metronome Setup.” (0–8b ☞PG p.58)

■Set the recording level

COpen the Sequencer P0: Play/REC, Sampling/HD Audio page.

DPlay your guitar at the volume you intend to record.

If the display indicates “ADC OVERLOAD!!” (AD con- verter input has overloaded!), turn the rear panel [LEVEL] knob to an appropriate level (toward the MIN position).

You will obtain the highest-quality sound at a point slightly below where the “ADC OVERLOAD!!” indica- tion appears; i.e., the highest level that does not cause an overload.

EPress the SEQUENCER [REC/WRITE] key.

When you play your guitar, the level meter will indicate the volume at which the guitar will be recorded.

If “CLIP!” appears, use the [VALUE] controller to lower the “Recording Level” slider shown in the right of the display from +0.0 to an appropriate level. This will not change the volume that is being output, but will affect the data that is recorded.

Use “WAVE File Play Level” (Global P0: 0–2a ☞PG p.138) to adjust the playback level.

FWhen you have finished making your adjustments, press the SEQUENCER [REC/WRITE] key.

When you press the SEQUENCER [REC/WRITE] key, you will be prevented from using “Track Select” to switch between MIDI tracks and audio tracks.

■Record

GIn the Sequencer P0: Play/REC, Preference page, set “Location” to the point in the song where you want to begin recording.

If you want to record from the beginning of the song, set this to 001:01.000.

HPress the SEQUENCER [REC/WRITE] key.

The TRITON STUDIO will enter the record-ready state. If you have set the metronome to be on, it will begin sound- ing.

10

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Update guide Table of Contents Program mode Global modeSampling mode Combination modeAbout this manual How this manual is organizedConventions in this manual Page Sequencer mode IntroductionNew functions in version Other new functions Updating the Triton Studio operating system Installing the systemPage Sequencer mode HD Audio RecordingAbout the HD Audio Track function About the audio tracks Audio Track 1&2 Erase Measure Create a directory in which to save the files Specify the location where the Wave file will be savedRecording an audio track Preparing to record an audio trackSetup Record the audio trackConnect your guitar Set the recording level RecordPress the Sequencer REC/WRITE key Press the Sequencer START/STOP key to stop recording Using punch-in recordingCheck the recorded content Punch In checked Punch In Mode AutoPerforming bounce recording Compare the recorded contentWhen you have finished setting your levels, stop play- back 1D Delete Song Menu commandsSequencer P0 Play/REC Track Select7c Recording Level dB Sampling/HD Audio7a Input COMBI, PROG, SEQ, S.PLAY, Disk 7b Ctrl ControlMenu Command Auditioning the contents of a Wave file7B Sel Dir/WAVE Audio Track 7D Bounce All Tracks To Song 7C Auto Sampling/HD Audio SetupBounce Off, On Punch In Mode Manual, AutoPreference Punch Off, OnSequencer P1 Cue List Changes to the page menu commands1R Put Wave New page menu commandsSequencer P5 Track Edit Track and Map1S Normalize/Level Normalize/Level Adjust 1T Volume Ramp1U Erase Punch Noise Start End To execute the Time Stretch command, press the OK but- ton1V Time Stretch IndexStereo file 1W Transfer Wave Transfer Wave To Midi Track1C Erase Track 1D Copy Track 1E Bounce TrackIf executing with Track Select set to a Midi track Track Dialog box when executing Erase Measure 1J Copy Measure 1K Move Measure 1Q Set Song Length Resample Auto Sampling/HD Audio SetupInitialize Resample SEQ PlayIn-Track Sampling Performing in-track samplingListen to the sampled data Listen to the Wave file that you created 2ch Mix to DiskHD Audio Track REC Resampling a completed song to create a Wave filePerform bounce-recording Bounce Audio TrackRecording on the audio tracks Check the audio tracks that you recordedParameter Initialize Resample SEQ Play In-Track Sampling Automatically-set parameters and their valuesDisk Support for exclusive events Recording and playing exclusive eventsRecording internal parameter changes Exclusive messages that can be realtime-recorded Recording exclusive messages received from the TRITON-RackMidi system exclusive parameter changes Effect IFX3 Put Effect Setting to TrackBeat.Tick Choose Put Effect Setting to Track to open the dialog boxSequencer P6 Pattern/RPPR 1B Event Edit1F Erase Measure Sequencer P8 Insert Effect Added page menu command1D Put Effect Setting to Track 1C Put Effect Setting to TrackTone Adjust Parameters 123456a Tone Adjust 1-Tone AdjustDestination and Value LFO1 Fade 99...+00...+99 LFO1 Dly LFO1 Delay 99...+00...+99LFO1 Spd LFO1 Speed 199...+00...+199 LFO1 P Int LFO1 Pitch Intensity -12.00...+00.00...+12.001N Quantize Swing 300%...+300% Copy From ProgramSwing Quantize Parameter 1L Copy From ProgramImprovements Auto Song Setup functionOther updates Compare functionEdit Wave Disk mode6b Wave Parameter 6F Insert 6K Volume Ramp6D Clear 6E CopyLoad Akai Volume Advanced Conversion Load Load Akai Program FileLoad Akai Program File 1D Load PCG RAM and Samples Load PCG RAM and SamplesExclusive Off, On Content that will be loaded from the .PCG fileContent loaded from the .SNG file Load Standard Midi FileSave Song as Standard Midi File Optimize Medium3J Optimize Medium Collect the song file and Wave file into a single directory Collect Audio Track file3K Collect Audio Track file Create a directory on the copy-destination mediaGlobal Karma function Global mode parametersRate Convert Loading Karma Music Workstation or Triton Le .PCG SNG filesData compatibility Scsi Mode/SCSI ID Global modeScsi Mode Initiator, Target Scsi Mode TargetScsi Mode Initiator Foot Switch AssignREC Audio Input Sampling modeAuto Sampling Setup 1O Auto Sampling SetupUse the radio buttons to select Auto Resample through IFX Auto Resample through IFXSampling Check the resampled dataIFX Menu commands Insert Mix, Paste Copying data from a Wave file, and inserting it in a sampleFrom, select Disk Page Use the radio buttons to select Resample Combination Play Combination mode5E Auto Sampling Setup Resample Combination PlayStart playing the combination that uses the arpeggiator etc Source Audio*2 Input1 Level 127 Pan L000 BUS Select 1C Copy From Program Program mode 3E Auto Sampling SetupResample Program Play Start playing the program that uses the arpeggiator etc Initialize Resample Program Play REC Audio Input Changed messages Other functionalityTap tempo control Various messagesAdded messages Korg INC
Top Page Image Contents