Korg V2 2ch Mix to Disk, HD Audio Track REC, Resampling a completed song to create a Wave file

Page 35

4. 2ch Mix to Disk

As a preparatory step to creating an audio CD from your completed song, you must resample your song to create a two-channel stereo WAVE file on the internal hard drive. (☞BG p.116)

The “2ch Mix to Disk” radio button automatically makes the necessary settings for creating this WAVE file.

■Setup

1Select “Auto Sampling/HD Audio Setup” to open the dialog box.

2Use radio buttons to select 2ch Mix to Disk.

3Press the OK button to execute “Auto Sampling/HD Audio Setup.” If you decide to cancel, press the Cancel button. (For the automatically-set parameters and their values, refer to p.32. For an example of using the auto- matically-set parameters ☞BG p.116)

■Resampling a completed song to create a WAVE file

4Select the song that you want to resample.

5Press the SAMPLING [REC] key.

6Press the SAMPLING [START/STOP] key. (Standby)

7Press the SEQUENCER [START/STOP] key. Song playback and resampling will begin.

8Press the SEQUENCER [START/STOP] key.

Song playback and resampling will end, and a WAVE file will be created.

If a “Buffer overrun error occurred” or “Buffer under- run error occurred” error message is displayed, refer to “What to do if a “Buffer overrun error occurred” or “Buffer underrun error occurred” error message appears during recording or playback” (☞p.13), and execute the Disk mode 0–3: Utility page menu com- mands “Optimize Medium” and “Collect Audio Track file.” If the error message “Buffer overrun error occurred” appeared during recording, the data recorded up to the point where the error occurred will have been recorded correctly, but the data at beyond the point the error appeared may not play back.

■Listen to the WAVE file that you created

•Use the Program mode page menu command “Select Directory” to play back the WAVE file. (Program 0–3D ☞PG p.7)

You can create an audio CD from the WAVE file you created. (☞BG p.118)

The Program mode page menu command “Select Directory” (Program 0–3D ☞PG p.7) specifies the save- destination of the WAVE file created by resampling.

5. HD Audio Track REC

“HD Audio Track REC” automatically adjusts the settings so that you can play back MIDI tracks while you record only an external two-channel audio source on the audio tracks.

(☞p.9)

Use INDIV. 1/2 OUT to monitor the audio signal being recorded. Connect the AUDIO OUTPUT MAIN L, R, INDIV1, and 2 jacks to your mixer so that you can mon- itor the output.

■Setup

1Select “Auto Sampling/HD Audio Setup” to open the dialog box.

2Use the radio buttons to select HD Audio Track REC.

3In “Source Audio,” select the external audio input source.

Analog: Selects the analog audio signal from a musical instrument or other device connected to the AUDIO INPUT 1 and AUDIO INPUT 2 jacks.

S/P DIF: Selects the digital audio signal from an instru- ment or DAT deck etc. connected to the S/P DIF jack. mLAN: Selects the digital audio signal from an instru- ment etc. connected to the mLAN connector (if the optional EXB-mLAN is installed). (☞PG p.4, PG p.56 “Input”)

If “Source Audio” is set to S/P DIF or mLAN, set “Sys- tem Clock” (Global P0: 0–2a☞PG p.138) to the appro- priate system clock setting.

4Use “Mono-1/Mono-2/Stereo”to specify the mono/ste- reo status of the input source. (☞PG p.4, PG p.56) Mono-1:Use Input 1.

Mono-2:Use Input 2.

Stereo: Use Input 1 and 2 in stereo.

5Use “To” to specify the track(s) that will be recorded. You can set this if the “Mono-1/Mono-2/Stereo” field is set to Mono-1 or Mono-2. If “Mono-1/Mono-2/Stereo” is set to Stereo, audio tracks 1 and 2 will be recorded.

6Press the OK button to execute “Auto Sampling/HD Audio Setup.” If you decide not to execute, press the Cancel button. (For the automatically-set parameters and their values, refer to p.32. For an example of using the automatically-set parameters ☞p.9)

30

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Update guide Table of Contents Program mode Global modeSampling mode Combination modeConventions in this manual About this manualHow this manual is organized Page New functions in version Sequencer modeIntroduction Other new functions Updating the Triton Studio operating system Installing the systemPage About the HD Audio Track function Sequencer modeHD Audio Recording About the audio tracks Audio Track 1&2 Erase Measure Create a directory in which to save the files Specify the location where the Wave file will be savedRecording an audio track Preparing to record an audio trackConnect your guitar SetupRecord the audio track Press the Sequencer REC/WRITE key Set the recording levelRecord Press the Sequencer START/STOP key to stop recording Using punch-in recordingCheck the recorded content Punch In checked Punch In Mode AutoPerforming bounce recording Compare the recorded contentWhen you have finished setting your levels, stop play- back 1D Delete Song Menu commandsSequencer P0 Play/REC Track Select7c Recording Level dB Sampling/HD Audio7a Input COMBI, PROG, SEQ, S.PLAY, Disk 7b Ctrl Control7B Sel Dir/WAVE Audio Track Menu CommandAuditioning the contents of a Wave file 7D Bounce All Tracks To Song 7C Auto Sampling/HD Audio SetupBounce Off, On Punch In Mode Manual, AutoPreference Punch Off, OnSequencer P1 Cue List Changes to the page menu commands1R Put Wave New page menu commandsSequencer P5 Track Edit Track and Map1U Erase Punch Noise 1S Normalize/Level Normalize/Level Adjust1T Volume Ramp Start End To execute the Time Stretch command, press the OK but- ton1V Time Stretch IndexStereo file 1W Transfer Wave Transfer Wave To Midi TrackIf executing with Track Select set to a Midi track Track 1C Erase Track1D Copy Track 1E Bounce Track Dialog box when executing Erase Measure 1J Copy Measure 1K Move Measure 1Q Set Song Length Resample Auto Sampling/HD Audio SetupInitialize Resample SEQ PlayListen to the sampled data In-Track SamplingPerforming in-track sampling Listen to the Wave file that you created 2ch Mix to DiskHD Audio Track REC Resampling a completed song to create a Wave filePerform bounce-recording Bounce Audio TrackRecording on the audio tracks Check the audio tracks that you recordedParameter Initialize Resample SEQ Play In-Track Sampling Automatically-set parameters and their valuesDisk Recording internal parameter changes Support for exclusive eventsRecording and playing exclusive events Exclusive messages that can be realtime-recorded Recording exclusive messages received from the TRITON-RackMidi system exclusive parameter changes Effect IFX3 Put Effect Setting to TrackBeat.Tick Choose Put Effect Setting to Track to open the dialog box1F Erase Measure Sequencer P6 Pattern/RPPR1B Event Edit Sequencer P8 Insert Effect Added page menu command1D Put Effect Setting to Track 1C Put Effect Setting to TrackDestination and Value Tone Adjust Parameters123456a Tone Adjust 1-Tone Adjust LFO1 Fade 99...+00...+99 LFO1 Dly LFO1 Delay 99...+00...+99LFO1 Spd LFO1 Speed 199...+00...+199 LFO1 P Int LFO1 Pitch Intensity -12.00...+00.00...+12.001N Quantize Swing 300%...+300% Copy From ProgramSwing Quantize Parameter 1L Copy From ProgramImprovements Auto Song Setup functionOther updates Compare functionEdit Wave Disk mode6b Wave Parameter 6F Insert 6K Volume Ramp6D Clear 6E CopyLoad Akai Program File Load Akai VolumeAdvanced Conversion Load Load Akai Program File 1D Load PCG RAM and Samples Load PCG RAM and SamplesExclusive Off, On Content that will be loaded from the .PCG fileContent loaded from the .SNG file Load Standard Midi File3J Optimize Medium Save Song as Standard Midi FileOptimize Medium Collect the song file and Wave file into a single directory Collect Audio Track file3K Collect Audio Track file Create a directory on the copy-destination mediaGlobal Karma function Global mode parametersRate Convert Loading Karma Music Workstation or Triton Le .PCG SNG filesData compatibility Scsi Mode/SCSI ID Global modeScsi Mode Initiator, Target Scsi Mode TargetScsi Mode Initiator Foot Switch AssignREC Audio Input Sampling modeAuto Sampling Setup 1O Auto Sampling SetupUse the radio buttons to select Auto Resample through IFX Auto Resample through IFXSampling Check the resampled dataIFX From, select Disk Menu commands Insert Mix, PasteCopying data from a Wave file, and inserting it in a sample Page Use the radio buttons to select Resample Combination Play Combination mode5E Auto Sampling Setup Resample Combination PlayStart playing the combination that uses the arpeggiator etc Source Audio*2 Input1 Level 127 Pan L000 BUS Select 1C Copy From Program Resample Program Play Program mode3E Auto Sampling Setup Start playing the program that uses the arpeggiator etc Initialize Resample Program Play REC Audio Input Changed messages Other functionalityTap tempo control Various messagesAdded messages Korg INC
Top Page Image Contents